Network Working Group M. Greene
Request for Comments: 2677 Contractor
Category: Standards Track J. Cucchiara
IronBridge Networks
J. Luciani
Bay Networks
August 1999
Definitions of Managed Objects for
the NBMA Next Hop Resolution Protocol (NHRP)
Status of this Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (1999). All Rights Reserved.
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes managed objects for the Next Hop
Resolution Protocol (NHRP) as defined in RFC 2332.
Table of Contents
1 Introduction ................................................. 2
2 The SNMP Management Framework ................................ 2
3 Structure of the MIB ......................................... 3
3.1 The NHRP General Group ..................................... 3
3.1.1 The NHRP Cache Table ..................................... 4
3.1.2 The NHRP Purge Request Table ............................. 4
3.2 The NHRP Client Group ...................................... 4
3.2.1 The NHRP Client Table .................................... 4
3.2.2 The NHRP Client Registration Table ....................... 5
3.2.3 The NHRP Client NHS Table ................................ 5
3.2.4 The NHRP Client Statistics Table ......................... 5
3.3 The NHRP Server Group ...................................... 5
3.3.1 The NHRP Server Table .................................... 5
3.3.2 The NHRP Server Cache Table .............................. 5
3.3.3 The NHRP Server NHC Table ................................ 6
Greene, et al. Standards Track [Page 1]RFC 2677 NHRP MIB August 1999
3.3.4 The NHRP Server Statistics Table ......................... 6
4 NBMA Next Hop Resolution Protocol MIB Definitions ............ 6
5 IANA Considerations .......................................... 62
6 Security ..................................................... 62
7 Intellectual Property ........................................ 63
8 Acknowledgments .............................................. 63
9 References ................................................... 64
10 Authors' Addresses .......................................... 66
11 Full Copyright Statement .................................... 67
1. Introduction
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes managed objects for the Next Hop
Resolution Protocol (NHRP) as defined in RFC 2332 [17].
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [21].
2. The SNMP Management Framework
The SNMP Management Framework presently consists of five major
components:
o An overall architecture, described in RFC 2571 [1].
o Mechanisms for describing and naming objects and events for the
purpose of management. The first version of this Structure of
Management Information (SMI) is called SMIv1 and described in
STD 16, RFC 1155 [2], STD 16, RFC 1212 [3] and RFC 1215 [4]. The
second version, called SMIv2, is described in STD 58, RFC 2578
[5], STD 58, RFC 2579 [6] and STD 58, RFC 2580 [7].
o Message protocols for transferring management information. The
first version of the SNMP message protocol is called SNMPv1 and
described in STD 15, RFC 1157 [8]. A second version of the SNMP
message protocol, which is not an Internet standards track
protocol, is called SNMPv2c and described in RFC 1901 [9] and RFC
1906 [10]. The third version of the message protocol is called
SNMPv3 and described in RFC 1906 [10], RFC 2572 [11] and RFC 2574
[12].
Greene, et al. Standards Track [Page 2]RFC 2677 NHRP MIB August 1999
o Protocol operations for accessing management information. The
first set of protocol operations and associated PDU formats is
described in STD 15, RFC 1157 [8]. A second set of protocol
operations and associated PDU formats is described in RFC 1905
[13].
o A set of fundamental applications described in RFC 2573 [14] and
the view-based access control mechanism described in RFC 2575
[15].
A more detailed introduction to the current SNMP Management Framework
can be found in RFC 2570 [16].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. Objects in the MIB are
defined using the mechanisms defined in the SMI.
This memo specifies a MIB module that is compliant to the SMIv2. A
MIB conforming to the SMIv1 can be produced through the appropriate
translations. The resulting translated MIB must be semantically
equivalent, except where objects or events are omitted because no
translation is possible (use of Counter64). Some machine readable
information in SMIv2 will be converted into textual descriptions in
SMIv1 during the translation process. However, this loss of machine
readable information is not considered to change the semantics of the
MIB.
3. Structure of the MIB
The NHRP MIB contains three groups: the General Group, the Client
Group, and the Server Group.
3.1. The NHRP General Group
The General Group contains objects that apply to both clients and
servers -- in particular the nhrpNextIndex scalar object, the NHRP
Cache Table and the NHRP Purge Request Table.
The nhrpNextIndex scalar object is used to provide unique indices for
the nhprClientIndex in the nhrpClientTable and the nhrpServerIndex in
the nhrpServerTable. If used consistently, this object may prevent
conflicts when multiple managers attempt to create rows
simultaneously in the same table.
Greene, et al. Standards Track [Page 3]RFC 2677 NHRP MIB August 1999
3.1.1. The NHRP Cache Table
The NHRP Cache Table represents the internetwork layer address to
NBMA address cache that is maintained by both NHRP clients and NHRP
servers.
The NHRP Cache Table contains an ifIndex as part of the Index Clause.
This ifIndex represents the use of a generic ifIndex, such that the
value of this ifIndex SHOULD reflect a specific NBMA subnetwork
related interface as determined by an implementation. For example,
assuming that the NBMA subnetwork is ATM, then it is up to the
implementors of this MIB to determine their own ATM interface
layering (assuming compliance with the IF-MIB, RFC 2233 [18] and the
ATM-MIB, RFC 2515 [19]). In other words, assuming that the NBMA
subnetwork is ATM, the ifIndex in the NHRP Cache Table would
represent the ifIndex containing or consisting of the VC (or
shortcut) denoted by this Table entry.
The indexing scheme for the NHRP Cache Table is very similar to the
MPC Ingress Cache Table and the MPS Ingress Cache Table in the
Multiprotocol Over ATM (MPOA) MIB [23]. This MIB and the MPOA MIB
were designed to be complementary and non-overlapping. The MPOA MIB
should also support this MIB. The MPOA MIB was designed prior to
this MIB, and was designed by the LANE/MPOA Working Group in the ATM
FORUM. The indexing scheme of the NHRP Cache Table (and the NHRP
Server Cache Table) reflect the indexing scheme of the MPC Ingress
Cache Table and the MPS Ingress Cache Table. Although, other
indexing schemes could have been used for the NHRP Cache Table, a
consistent indexing scheme between these tables was thought to be
more advantageous from an implementation standpoint.
3.1.2. The NHRP Purge Request Table
The NHRP Purge Request Table is a way to track Purge Request
Information.
3.2. The NHRP Client Group
The Client Group contains objects that only apply to NHRP clients
(NHCs).
3.2.1. The NHRP Client Table
The NHRP Client Table contains entries for NHRP Next Hop Clients
(NHCs) associated with this agent. Each row in the table represents
a single NHC. The RequestID used in Registration requests needs to
be saved to non-volatile storage. Depending upon the implementation,
Greene, et al. Standards Track [Page 4]
RFC 2677 NHRP MIB August 1999
this may or may not impact how the StorageType is used. For a
complete description of how the Registration RequestID is used, see
Section 5.2.3 of [17].
3.2.2. The NHRP Client Registration Table
The NHRP Client Registration Table contains information on
registration requests which need to be maintained by the Clients.
Each entry in this table represents a single registration request.
Note: since the NHRP specification does not mandate a refresh
algorithm, this table omits refresh information, however, this table
does contain information for all the registration requests which need
to be maintained by the NHRP Clients.
3.2.3. The NHRP Client NHS Table
The NHRP Client NHS Table contains the NBMA subnetwork addresses of
servers configured for use by the client. By default, the agent will
add an entry to this table which corresponds to the client's default
router.
3.2.4. The NHRP Client Statistics Table
The NHRP Client Statistics Table contains NHRP statistics maintained
by a client. These statistics include counters on requests and
replies, as well as counters for errors which are encountered by the
Clients.
3.3. The NHRP Server Group
The Server Group contains objects that only apply to NHRP servers
(NHSes).
3.3.1. The NHRP Server Table
The NHRP Server Table contains entries for each server associated
with this agent.
3.3.2. The NHRP Server Cache Table
The NHRP Server Cache Table contains additional objects that a server
keeps for each entry in its cache. This table extends the NHRP Cache
Table defined in the General Group.
Greene, et al. Standards Track [Page 5]
RFC 2677 NHRP MIB August 1999
3.3.3. The NHRP Server NHC Table
This table contains information about all the Clients known to the
Servers.
3.3.4. The NHRP Server Statistics Table
The NHRP Server Statistics Table contains NHRP statistics maintained
by a server. These statistics include counters on requests and
replies, as well as counters for errors which are encountered by the
Servers.
4. NBMA Next Hop Resolution Protocol MIB Definitions
NHRP-MIB DEFINITIONS ::= BEGIN
IMPORTS
OBJECT-TYPE, MODULE-IDENTITY, mib-2, Integer32,
Counter32, Unsigned32
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
TEXTUAL-CONVENTION, TruthValue, RowStatus, StorageType,
TimeStamp
FROM SNMPv2-TC
ifIndex
FROM IF-MIB
AddressFamilyNumbers
FROM IANA-ADDRESS-FAMILY-NUMBERS-MIB
;
nhrpMIB MODULE-IDENTITY
LAST-UPDATED "9908260000Z" -- August 26, 1999
ORGANIZATION "Internetworking Over NBMA (ion) Working Group"
CONTACT-INFO
"Maria Greene (maria@xedia.com)
Contractor
Joan Cucchiara (joan@ironbridgenetworks.com)
IronBridge Networks
James V. Luciani (luciani@baynetworks.com)
Bay Networks"
Greene, et al. Standards Track [Page 6]RFC 2677 NHRP MIB August 1999
DESCRIPTION
"This MIB contains managed object definitions for the Next
Hop Resolution Procol, NHRP, as defined in RFC 2332 [17]."
-- revision history
REVISION "9908260000Z" -- August 26, 1999
DESCRIPTION "Initial version, published as RFC 2677."
::= { mib-2 71 }
--****************************************************************
-- NHRP Textual Conventions
--****************************************************************
NhrpGenAddr ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The value of an internetwork layer or NBMA address."
SYNTAX OCTET STRING (SIZE (0..64))
nhrpObjects OBJECT IDENTIFIER ::= { nhrpMIB 1 }
--****************************************************************
-- NHRP General (Client and Server) Objects
--****************************************************************
nhrpGeneralObjects OBJECT IDENTIFIER ::= { nhrpObjects 1 }
--
-- The following scalar is to be used to
-- provided indices for the
-- nhrpClientTable, and/or the nhrpServerTable.
--
nhrpNextIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This scalar is used for creating rows in the
nhrpClientTable and the nhrpServerTable.
The value of this variable is a currently unused value
for nhrpClientIndex and nhrpServerIndex.
Greene, et al. Standards Track [Page 7]RFC 2677 NHRP MIB August 1999
The value returned when reading this variable must be
unique for the NHC's and NHS's indices associated with
this row. Subsequent attempts to read this variable
must return different values.
NOTE: this object exists in the General Group because
it is to be used in establishing rows in the
nhrpClientTable and the nhrpServerTable. In other words,
the value retrieved from this object could become the
value of nhrpClientIndex and nhprServerIndex.
In the situation of an agent re-initialization the value
of this object must be saved in non-volatile storage.
This variable will return the special value 0 if no new
rows can be created."
::= { nhrpGeneralObjects 1 }
--
-- The NHRP Cache Table
--
nhrpCacheTable OBJECT-TYPE
SYNTAX SEQUENCE OF NhrpCacheEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains mappings between internetwork layer
addresses and NBMA subnetwork layer addresses."
::= { nhrpGeneralObjects 2 }
nhrpCacheEntry OBJECT-TYPE
SYNTAX NhrpCacheEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A cached mapping between an internetwork layer address
and an NBMA address. Entries can be created by the
network administrator using the nhrpCacheRowStatus
column, or they may be added dynamically based on
protocol operation (including NHRP, SCSP, and others,
such as ATMARP).
When created based by NHRP protocol operations
this entry is largely based on contents contained in
the Client Information Entry (CIE).
Greene, et al. Standards Track [Page 8]RFC 2677 NHRP MIB August 1999
Zero or more Client Information Entries (CIEs) may be
included in the NHRP Packet. For a complete description
of the CIE, refer to Section 5.2.0.1 of
RFC 2332 [17]."
INDEX {
nhrpCacheInternetworkAddrType,
nhrpCacheInternetworkAddr,
ifIndex,
nhrpCacheIndex
}
::= { nhrpCacheTable 1 }
NhrpCacheEntry ::= SEQUENCE {
nhrpCacheInternetworkAddrType AddressFamilyNumbers,
nhrpCacheInternetworkAddr NhrpGenAddr,
nhrpCacheIndex Unsigned32,
nhrpCachePrefixLength Integer32,
nhrpCacheNextHopInternetworkAddr NhrpGenAddr,
nhrpCacheNbmaAddrType AddressFamilyNumbers,
nhrpCacheNbmaAddr NhrpGenAddr,
nhrpCacheNbmaSubaddr NhrpGenAddr,
nhrpCacheType INTEGER,
nhrpCacheState INTEGER,
nhrpCacheHoldingTimeValid TruthValue,
nhrpCacheHoldingTime Unsigned32,
nhrpCacheNegotiatedMtu Integer32,
nhrpCachePreference Integer32,
nhrpCacheStorageType StorageType,
nhrpCacheRowStatus RowStatus
}
nhrpCacheInternetworkAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The internetwork layer address type of this Next Hop
Resolution Cache entry. The value of this object indicates
how to interpret the values of nhrpCacheInternetworkAddr
and nhrpCacheNextHopInternetworkAddr."
::= { nhrpCacheEntry 1 }
nhrpCacheInternetworkAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS not-accessible
STATUS current
Greene, et al. Standards Track [Page 9]RFC 2677 NHRP MIB August 1999
DESCRIPTION
"The value of the internetwork address of the
destination."
::= { nhrpCacheEntry 2 }
nhrpCacheIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An identifier for this entry that has local
significance within the scope of the General
Group. This identifier is used here to
uniquely identify this row, and also used
in the 'nhrpPurgeTable' for the value of
the 'nhrpPurgeCacheIdentifier'."
::= { nhrpCacheEntry 3 }
nhrpCachePrefixLength OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of bits that define the internetwork layer
prefix associated with the nhrpCacheInternetworkAddr."
::= { nhrpCacheEntry 4 }
nhrpCacheNextHopInternetworkAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the internetwork address of the next hop."
::= { nhrpCacheEntry 5 }
nhrpCacheNbmaAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The NBMA address type. The value of this
object indicates how to interpret
the values of nhrpCacheNbmaAddr and
nhrpCacheNbmaSubaddr."
::= { nhrpCacheEntry 6 }
Greene, et al. Standards Track [Page 10]RFC 2677 NHRP MIB August 1999
nhrpCacheNbmaAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the NBMA subnetwork address of the next
hop."
::= { nhrpCacheEntry 7 }
nhrpCacheNbmaSubaddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the NBMA subaddress of the next hop. If
there is no subaddress concept for the NBMA address
family, this value will be a zero-length OCTET STRING."
::= { nhrpCacheEntry 8 }
nhrpCacheType OBJECT-TYPE
SYNTAX INTEGER {
other(1),
register(2),
resolveAuthoritative(3),
resoveNonauthoritative(4),
transit(5),
administrativelyAdded(6),
atmarp(7),
scsp(8)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An indication of how this cache entry
was created. The values are:
'other(1)' The entry was added by some
other means.
'register(2)' In a server, added based on a
client registration.
'resolveAuthoritative(3)' In a client, added based on
receiving an Authoritative
NHRP Resolution Reply.
Greene, et al. Standards Track [Page 11]RFC 2677 NHRP MIB August 1999
'resolveNonauthoritative(4)' In a client, added based on
receiving a Nonauthoritative
NHRP Resolution Reply.
'transit(5)' In a transit server, added by
examining a forwarded NHRP
packet.
'administrativelyAdded(6)' In a client or server,
manually added by the
administrator. The
StorageType of this entry is
reflected in
'nhrpCacheStorageType'.
'atmarp(7)' The entry was added due to an
ATMARP.
'scsp(8)' The entry was added due to
SCSP.
When the entry is under creation using the
nhrpCacheRowStatus column, the only value that can be
specified by the administrator is 'administrativelyAdded'.
Attempting to set any other value will cause an
'inconsistentValue' error.
The value cannot be modified once the entry is active."
::= { nhrpCacheEntry 9 }
nhrpCacheState OBJECT-TYPE
SYNTAX INTEGER {
incomplete(1),
ackReply(2),
nakReply(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An indication of the state of this entry. The values are:
'incomplete(1)' The client has sent a NHRP Resolution
Request but has not yet received the
NHRP Resolution Reply.
Greene, et al. Standards Track [Page 12]RFC 2677 NHRP MIB August 1999
'ackReply(2)' For a client or server, this is a
cached valid mapping.
'nakReply(3)' For a client or server, this is a
cached NAK mapping."
::= { nhrpCacheEntry 10 }
nhrpCacheHoldingTimeValid OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"True(1) is returned if the value of
'nhrpCacheType' is not
'administrativelyAdded'. Since the
value of 'nhrpCacheType' was not
configured by a user, the value of
'nhrpCacheHoldingTime' is
considered valid. In other words, the value of
'nhrpCacheHoldingTime' represents
the Holding Time for the cache Entry.
If 'nhrpCacheType has been configured by a
user, (i.e. the value of 'nhrpCacheType' is
'administrativelyAdded') then false(2) will be returned.
This indicates that the value of
'nhrpCacheHoldingTime' is undefined because this row
could possibly be backed up in nonvolatile storage."
::= { nhrpCacheEntry 11 }
nhrpCacheHoldingTime OBJECT-TYPE
SYNTAX Unsigned32(0..65535)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the value of 'nhrpCacheHoldingTimeValid is
true(1) then this object represents the number
of seconds that the cache entry will remain in this
table. When this value reaches 0 (zero) the row should
be deleted.
If the value of 'nhrpCacheHoldingTimeValid is
false(2) then this object is undefined."
::= { nhrpCacheEntry 12 }
Greene, et al. Standards Track [Page 13]RFC 2677 NHRP MIB August 1999
nhrpCacheNegotiatedMtu OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum transmission unit (MTU) that was negotiated
or registered for this entity. In other words, this is the
actual MTU being used."
::= { nhrpCacheEntry 13 }
nhrpCachePreference OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object which reflects the Preference value of the
Client Information Entry (CIE).
Zero or more Client Information Entries (CIEs) may be
included in the NHRP Packet. One of the fields in the
CIE is the Preference. For a complete description of
the CIE, refer to Section 5.2.0.1 of RFC 2332 [17]."
REFERENCE
"Section 5.2.0.1 Mandatory Part Format, RFC 2332 [17]."
::= { nhrpCacheEntry 14 }
nhrpCacheStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This value only has meaning when the 'nhrpCacheType'
has the value of 'administrativelyAdded'.
When the row is created due to being
'administrativelyAdded', this object reflects whether
this row is kept in volatile storage
and lost upon reboot or if this row is backed up by
non-volatile or permanent storage.
If the value of 'nhrpCacheType' has a value which
is not 'administrativelyAdded, then the value of this
object is 'other(1)'."
DEFVAL { nonVolatile }
::= { nhrpCacheEntry 15 }
Greene, et al. Standards Track [Page 14]RFC 2677 NHRP MIB August 1999
nhrpCacheRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be
created and deleted using the RowStatus convention."
::= { nhrpCacheEntry 16 }
--
-- The NHRP Purge Request Table
--
nhrpPurgeReqTable OBJECT-TYPE
SYNTAX SEQUENCE OF NhrpPurgeReqEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table will track Purge Request Information."
::= { nhrpGeneralObjects 3 }
nhrpPurgeReqEntry OBJECT-TYPE
SYNTAX NhrpPurgeReqEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information regarding a Purge Request."
INDEX { nhrpPurgeIndex }
::= { nhrpPurgeReqTable 1 }
NhrpPurgeReqEntry ::= SEQUENCE {
nhrpPurgeIndex Unsigned32,
nhrpPurgeCacheIdentifier Unsigned32,
nhrpPurgePrefixLength Integer32,
nhrpPurgeRequestID Unsigned32,
nhrpPurgeReplyExpected TruthValue,
nhrpPurgeRowStatus RowStatus
}
nhrpPurgeIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index for this entry that has local significance
within the scope of this table."
::= { nhrpPurgeReqEntry 1 }
Greene, et al. Standards Track [Page 15]RFC 2677 NHRP MIB August 1999
nhrpPurgeCacheIdentifier OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object identifies which row in
'nhrpCacheTable' is being purged. This object
should have the same value as the 'nhrpCacheIndex'
in the 'nhrpCacheTable'."
::= { nhrpPurgeReqEntry 2 }
nhrpPurgePrefixLength OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"In the case of NHRP Purge Requests, this specifies the
equivalence class of addresses which match the first
'Prefix Length' bit positions of the Client Protocol
Address specified in the Client Information Entry (CIE)."
::= { nhrpPurgeReqEntry 3 }
nhrpPurgeRequestID OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Request ID used in the purge request."
::= { nhrpPurgeReqEntry 4 }
nhrpPurgeReplyExpected OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An indication of whether this Purge Request has the
'N' Bit cleared (off)."
::= { nhrpPurgeReqEntry 5 }
nhrpPurgeRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be
created and deleted using the RowStatus convention."
::= { nhrpPurgeReqEntry 6 }
Greene, et al. Standards Track [Page 16]RFC 2677 NHRP MIB August 1999
--****************************************************************
-- NHRP Client Objects
--****************************************************************
nhrpClientObjects OBJECT IDENTIFIER ::= { nhrpObjects 2 }
--
-- The NHRP Client Table
--
nhrpClientTable OBJECT-TYPE
SYNTAX SEQUENCE OF NhrpClientEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about NHRP clients (NHCs) managed by this
agent."
::= { nhrpClientObjects 1 }
nhrpClientEntry OBJECT-TYPE
SYNTAX NhrpClientEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a single NHC."
INDEX { nhrpClientIndex }
::= { nhrpClientTable 1 }
NhrpClientEntry ::= SEQUENCE {
nhrpClientIndex Unsigned32,
nhrpClientInternetworkAddrType AddressFamilyNumbers,
nhrpClientInternetworkAddr NhrpGenAddr,
nhrpClientNbmaAddrType AddressFamilyNumbers,
nhrpClientNbmaAddr NhrpGenAddr,
nhrpClientNbmaSubaddr NhrpGenAddr,
nhrpClientInitialRequestTimeout Integer32,
nhrpClientRegistrationRequestRetries Integer32,
nhrpClientResolutionRequestRetries Integer32,
nhrpClientPurgeRequestRetries Integer32,
nhrpClientDefaultMtu Unsigned32,
nhrpClientHoldTime Unsigned32,
nhrpClientRequestID Unsigned32,
nhrpClientStorageType StorageType,
nhrpClientRowStatus RowStatus
}
Greene, et al. Standards Track [Page 17]RFC 2677 NHRP MIB August 1999
nhrpClientIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An identifier for the NHRP client that is unique within
the scope of this agent. The 'nhrpNextIndex' value
should be consulted (read), prior to creating a row in
this table, and the value returned from reading
'nhrpNextIndex' should be used as this object's value."
::= { nhrpClientEntry 1 }
nhrpClientInternetworkAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the internetwork layer address of this
client. This object indicates how the value of
nhrpClientInternetworkAddr is to be interpreted."
::= { nhrpClientEntry 2 }
nhrpClientInternetworkAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the internetwork layer address of this
client."
::= { nhrpClientEntry 3 }
nhrpClientNbmaAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the NBMA subnetwork address of this client.
This object indicates how the values of
nhrpClientNbmaAddr and nhrpClientNbmaSubaddr are to be
interpreted."
::= { nhrpClientEntry 4 }
nhrpClientNbmaAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
Greene, et al. Standards Track [Page 18]RFC 2677 NHRP MIB August 1999
DESCRIPTION
"The NBMA subnetwork address of this client."
::= { nhrpClientEntry 5 }
nhrpClientNbmaSubaddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The NBMA subaddress of this client. For NBMA address
families without a subaddress concept, this will be a
zero-length OCTET STRING."
::= { nhrpClientEntry 6 }
nhrpClientInitialRequestTimeout OBJECT-TYPE
SYNTAX Integer32 (1..900)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds that the client will wait before
timing out an NHRP initial request. This object only has
meaning for the initial timeout period."
DEFVAL { 10 }
::= { nhrpClientEntry 7 }
nhrpClientRegistrationRequestRetries OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of times the client will retry the
registration request before failure. A value of
0 means don't retry. A value of 65535 means
retry forever."
DEFVAL { 3 }
::= { nhrpClientEntry 8 }
nhrpClientResolutionRequestRetries OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of times the client will retry the resolution
request before failure. A value of 0 means don't retry.
A value of 65535 means retry forever."
DEFVAL { 3 }
::= { nhrpClientEntry 9 }
Greene, et al. Standards Track [Page 19]RFC 2677 NHRP MIB August 1999
nhrpClientPurgeRequestRetries OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of times the client will retry a purge request
before failure. A value of 0 means don't retry. A value of
65535 means retry forever."
DEFVAL { 3 }
::= { nhrpClientEntry 10 }
nhrpClientDefaultMtu OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The default maximum transmission unit (MTU) of the
LIS/LAG which this client should use. This object
will be initialized by the agent to the default MTU
of the LIS/LAG (which is 9180) unless a different MTU
value is specified during creation of this Client."
REFERENCE
"RFC 2225 [25], Classical IP and ARP over ATM, Section 7,
DEFAULT VALUE FOR IP MTU OVER ATM AAL5."
DEFVAL { 9180 }
::= { nhrpClientEntry 11 }
nhrpClientHoldTime OBJECT-TYPE
SYNTAX Unsigned32(0..65535)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The hold time the client will register."
DEFVAL { 900 }
::= { nhrpClientEntry 12 }
nhrpClientRequestID OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Request ID used to register this client with its
server. According to Section 5.2.3 of the NHRP
Specification, RFC 2332 [17], the Request ID must
be kept in non-volatile storage, so that if an NHC
crashes and re-initializes, it will use a different
Greene, et al. Standards Track [Page 20]RFC 2677 NHRP MIB August 1999
Request ID during the registration process
when reregistering with the same NHS."
REFERENCE
"Section 5.2.3 NHRP Registration Request, RFC 2332 [17]."
::= { nhrpClientEntry 13 }
nhrpClientStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object defines whether this row is kept in
volatile storage and lost upon a Client crash or
reboot situation, or if this row is backed up by
nonvolatile or permanent storage."
DEFVAL { nonVolatile }
::= { nhrpClientEntry 14 }
nhrpClientRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be
created and deleted using the RowStatus convention."
::= { nhrpClientEntry 15 }
--
-- The NHRP Client Registration Table
--
nhrpClientRegistrationTable OBJECT-TYPE
SYNTAX SEQUENCE OF NhrpClientRegistrationEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of Registration Request Information that
needs to be maintained by the NHCs (clients)."
REFERENCE
"Section 5.2.3 NHRP Registration Request, RFC 2332 [17]."
::= { nhrpClientObjects 2 }
nhrpClientRegistrationEntry OBJECT-TYPE
SYNTAX NhrpClientRegistrationEntry
MAX-ACCESS not-accessible
STATUS current
Greene, et al. Standards Track [Page 21]RFC 2677 NHRP MIB August 1999
DESCRIPTION
"An NHC needs to maintain registration request information
between the NHC and the NHS. An entry in this table
represents information for a single registration request."
INDEX { nhrpClientIndex,
nhrpClientRegIndex
}
::= { nhrpClientRegistrationTable 1 }
NhrpClientRegistrationEntry ::= SEQUENCE {
nhrpClientRegIndex Unsigned32,
nhrpClientRegUniqueness INTEGER,
nhrpClientRegState INTEGER,
nhrpClientRegRowStatus RowStatus
}
nhrpClientRegIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An identifier for this entry such that it
identifies a specific Registration Request from
the NHC represented by the nhrpClientIndex."
::= { nhrpClientRegistrationEntry 1 }
nhrpClientRegUniqueness OBJECT-TYPE
SYNTAX INTEGER {
requestUnique(1),
requestNotUnique(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Uniqueness indicator for this Registration Request.
If this object has the value of requestUnique(1), then
the Uniqueness bit is set in the the NHRP Registration
Request represented by this row. The value cannot
be changed once the row is created."
::= { nhrpClientRegistrationEntry 2 }
nhrpClientRegState OBJECT-TYPE
SYNTAX INTEGER {
other(1),
registering(2),
ackRegisterReply(3),
nakRegisterReply(4)
Greene, et al. Standards Track [Page 22]RFC 2677 NHRP MIB August 1999
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The registration state of this client. The values are:
'other(1)' The state of the registration
request is not one of
'registering',
'ackRegisterReply' or
'nakRegisterReply'.
'registering(2)' A registration request has
been issued and a registration
reply is expected.
'ackRegisterReply(3)' A positive registration reply
has been received.
'nakRegisterReply(4)' The client has received a
negative registration
reply (NAK)."
::= { nhrpClientRegistrationEntry 3 }
nhrpClientRegRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be
created and deleted using the RowStatus convention."
::= { nhrpClientRegistrationEntry 4 }
--
-- The NHRP Client->Server Table
--
nhrpClientNhsTable OBJECT-TYPE
SYNTAX SEQUENCE OF NhrpClientNhsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of NHSes that are available for use by this NHC
(client). By default, the agent will add an entry to this
table that corresponds to the client's default router."
::= { nhrpClientObjects 3 }
Greene, et al. Standards Track [Page 23]RFC 2677 NHRP MIB August 1999
nhrpClientNhsEntry OBJECT-TYPE
SYNTAX NhrpClientNhsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An NHS that may be used by an NHC."
INDEX { nhrpClientIndex, nhrpClientNhsIndex }
::= { nhrpClientNhsTable 1 }
NhrpClientNhsEntry ::= SEQUENCE {
nhrpClientNhsIndex Unsigned32,
nhrpClientNhsInternetworkAddrType AddressFamilyNumbers,
nhrpClientNhsInternetworkAddr NhrpGenAddr,
nhrpClientNhsNbmaAddrType AddressFamilyNumbers,
nhrpClientNhsNbmaAddr NhrpGenAddr,
nhrpClientNhsNbmaSubaddr NhrpGenAddr,
nhrpClientNhsInUse TruthValue,
nhrpClientNhsRowStatus RowStatus
}
nhrpClientNhsIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An identifier for an NHS available to an NHC."
::= { nhrpClientNhsEntry 1 }
nhrpClientNhsInternetworkAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the internetwork layer address of the
NHRP server represented in this entry. This object
indicates how the value of
nhrpClientNhsInternetworkAddr is to be interpreted."
::= { nhrpClientNhsEntry 2 }
nhrpClientNhsInternetworkAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the destination internetwork layer
address of the NHRP server represented by this
Greene, et al. Standards Track [Page 24]RFC 2677 NHRP MIB August 1999
entry. If this value is not known, this will be
a zero-length OCTET STRING."
::= { nhrpClientNhsEntry 3 }
nhrpClientNhsNbmaAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the NBMA subnetwork address of the NHRP
Server represented by this entry. This object indicates
how the values of nhrpClientNhsNbmaAddr and
nhrpClientNhsNbmaSubaddr are to be interpreted."
::= { nhrpClientNhsEntry 4 }
nhrpClientNhsNbmaAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The NBMA subnetwork address of the NHS. The type of
the address is indicated by the corresponding value of
nhrpClientNhsNbmaAddrType."
::= { nhrpClientNhsEntry 5 }
nhrpClientNhsNbmaSubaddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The NBMA subaddress of the NHS. For NMBA address
families that do not have the concept of subaddress,
this will be a zero-length OCTET STRING."
::= { nhrpClientNhsEntry 6 }
nhrpClientNhsInUse OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An indication of whether this NHS is in use by the NHC."
::= { nhrpClientNhsEntry 7 }
nhrpClientNhsRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
Greene, et al. Standards Track [Page 25]RFC 2677 NHRP MIB August 1999
DESCRIPTION
"An object that allows entries in this table to be
created and deleted using the RowStatus convention."
::= { nhrpClientNhsEntry 8 }
--
-- The NHRP Client StatisticsTable
--
nhrpClientStatTable OBJECT-TYPE
SYNTAX SEQUENCE OF NhrpClientStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains statistics collected by NHRP
clients."
::= { nhrpClientObjects 4 }
nhrpClientStatEntry OBJECT-TYPE
SYNTAX NhrpClientStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Statistics collected by a NHRP client."
INDEX { nhrpClientIndex }
::= { nhrpClientStatTable 1 }
NhrpClientStatEntry ::= SEQUENCE {
nhrpClientStatTxResolveReq Counter32,
nhrpClientStatRxResolveReplyAck Counter32,
nhrpClientStatRxResolveReplyNakProhibited Counter32,
nhrpClientStatRxResolveReplyNakInsufResources Counter32,
nhrpClientStatRxResolveReplyNakNoBinding Counter32,
nhrpClientStatRxResolveReplyNakNotUnique Counter32,
nhrpClientStatTxRegisterReq Counter32,
nhrpClientStatRxRegisterAck Counter32,
nhrpClientStatRxRegisterNakProhibited Counter32,
nhrpClientStatRxRegisterNakInsufResources Counter32,
nhrpClientStatRxRegisterNakAlreadyReg Counter32,
nhrpClientStatRxPurgeReq Counter32,
nhrpClientStatTxPurgeReq Counter32,
nhrpClientStatRxPurgeReply Counter32,
nhrpClientStatTxPurgeReply Counter32,
nhrpClientStatTxErrorIndication Counter32,
nhrpClientStatRxErrUnrecognizedExtension Counter32,
nhrpClientStatRxErrLoopDetected Counter32,
Greene, et al. Standards Track [Page 26]RFC 2677 NHRP MIB August 1999
nhrpClientStatRxErrProtoAddrUnreachable Counter32,
nhrpClientStatRxErrProtoError Counter32,
nhrpClientStatRxErrSduSizeExceeded Counter32,
nhrpClientStatRxErrInvalidExtension Counter32,
nhrpClientStatRxErrAuthenticationFailure Counter32,
nhrpClientStatRxErrHopCountExceeded Counter32,
nhrpClientStatDiscontinuityTime TimeStamp
}
nhrpClientStatTxResolveReq OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Resolution Requests transmitted
by this client.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 1 }
nhrpClientStatRxResolveReplyAck OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of positively acknowledged NHRP Resolution
Replies received by this client.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 2 }
nhrpClientStatRxResolveReplyNakProhibited OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NAKed NHRP Resolution Replies received
by this client that contained the code indicating
'Administratively Prohibited'.
Greene, et al. Standards Track [Page 27]RFC 2677 NHRP MIB August 1999
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 3 }
nhrpClientStatRxResolveReplyNakInsufResources OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NAKed NHRP Resolution Replies received
by this client that contained the code indicating
'Insufficient Resources'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 4 }
nhrpClientStatRxResolveReplyNakNoBinding OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NAKed NHRP Resolution Replies received
by this client that contained the code indicating
'No Internetworking Layer Address to NBMA Address
Binding Exists'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 5 }
nhrpClientStatRxResolveReplyNakNotUnique OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
Greene, et al. Standards Track [Page 28]RFC 2677 NHRP MIB August 1999
DESCRIPTION
"The number of NAKed NHRP Resolution Replies received
by this client that contained the code indicating
'Binding Exists But Is Not Unique'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 6 }
nhrpClientStatTxRegisterReq OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Registration Requests transmitted
by this client.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 7 }
nhrpClientStatRxRegisterAck OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of positively acknowledged NHRP Registration
Replies received by this client.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 8 }
nhrpClientStatRxRegisterNakProhibited OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
Greene, et al. Standards Track [Page 29]RFC 2677 NHRP MIB August 1999
DESCRIPTION
"The number of NAKed NHRP Registration Replies received
by this client that contained the code indicating
'Administratively Prohibited'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 9 }
nhrpClientStatRxRegisterNakInsufResources OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NAKed NHRP Registration Replies received
by this client that contained the code indicating
'Insufficient Resources'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 10 }
nhrpClientStatRxRegisterNakAlreadyReg OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NAKed NHRP Registration Replies received
by this client that contained the code indicating 'Unique
Internetworking Layer Address Already Registered'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 11 }
nhrpClientStatRxPurgeReq OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
Greene, et al. Standards Track [Page 30]RFC 2677 NHRP MIB August 1999
DESCRIPTION
"The number of NHRP Purge Requests received by this
client.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 12 }
nhrpClientStatTxPurgeReq OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Purge Requests transmitted by this
client.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 13 }
nhrpClientStatRxPurgeReply OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Purge Replies received by this
client.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 14 }
nhrpClientStatTxPurgeReply OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Purge Replies transmitted by this
client.
Greene, et al. Standards Track [Page 31]RFC 2677 NHRP MIB August 1999
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 15 }
nhrpClientStatTxErrorIndication OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets transmitted
by this client.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 16 }
nhrpClientStatRxErrUnrecognizedExtension OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets received
by this client with the error code
'Unrecognized Extension'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 17 }
nhrpClientStatRxErrLoopDetected OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
Greene, et al. Standards Track [Page 32]RFC 2677 NHRP MIB August 1999
DESCRIPTION
"The number of NHRP Error Indication packets received
by this client with the error code 'NHRP Loop Detected'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 18 }
nhrpClientStatRxErrProtoAddrUnreachable OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets received
by this client with the error code 'Protocol Address
Unreachable'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 19 }
nhrpClientStatRxErrProtoError OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets received
by this client with the error code 'Protocol Error'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 20 }
Greene, et al. Standards Track [Page 33]RFC 2677 NHRP MIB August 1999
nhrpClientStatRxErrSduSizeExceeded OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets received
by this client with the error code 'NHRP SDU Size
Exceeded'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 21 }
nhrpClientStatRxErrInvalidExtension OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets received
by this client with the error code 'Invalid Extension'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 22 }
nhrpClientStatRxErrAuthenticationFailure OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets received
by this client with the error code 'Authentication
Failure'.
Greene, et al. Standards Track [Page 34]RFC 2677 NHRP MIB August 1999
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 23 }
nhrpClientStatRxErrHopCountExceeded OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets received
by this client with the error code 'Hop Count Exceeded'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 24 }
nhrpClientStatDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion at
which any one or more of this Client's counters
suffered a discontinuity. If no such discontinuities
have occurred since the last re-initialization of the
local management subsystem or the NHRP Client
re-initialization associated with this entry, then
this object contains a zero value."
REFERENCE
"RFC 2233 [18]."
::= { nhrpClientStatEntry 25 }
Greene, et al. Standards Track [Page 35]RFC 2677 NHRP MIB August 1999
--****************************************************************
-- NHRP Server Objects
--****************************************************************
nhrpServerObjects OBJECT IDENTIFIER ::= { nhrpObjects 3 }
--
-- The NHRP Next Hop Server Table
--
nhrpServerTable OBJECT-TYPE
SYNTAX SEQUENCE OF NhrpServerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information for a set of NHSes
associated with this agent."
::= { nhrpServerObjects 1 }
nhrpServerEntry OBJECT-TYPE
SYNTAX NhrpServerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a single NHS."
INDEX { nhrpServerIndex }
::= { nhrpServerTable 1 }
NhrpServerEntry ::= SEQUENCE {
nhrpServerIndex Unsigned32,
nhrpServerInternetworkAddrType AddressFamilyNumbers,
nhrpServerInternetworkAddr NhrpGenAddr,
nhrpServerNbmaAddrType AddressFamilyNumbers,
nhrpServerNbmaAddr NhrpGenAddr,
nhrpServerNbmaSubaddr NhrpGenAddr,
nhrpServerStorageType StorageType,
nhrpServerRowStatus RowStatus
}
nhrpServerIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An identifier for the server that is unique within the
scope of this agent."
::= { nhrpServerEntry 1 }
Greene, et al. Standards Track [Page 36]RFC 2677 NHRP MIB August 1999
nhrpServerInternetworkAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the internetwork layer address of this
server. This object is used to interpret the value of
nhrpServerInternetworkAddr."
::= { nhrpServerEntry 2 }
nhrpServerInternetworkAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the internetwork layer address of this
server."
::= { nhrpServerEntry 3 }
nhrpServerNbmaAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the NBMA subnetwork address of this server.
This object is used to interpret the value of
nhrpServerNbmaAddr."
::= { nhrpServerEntry 4 }
nhrpServerNbmaAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the NBMA subnetwork address of this
server."
::= { nhrpServerEntry 5 }
nhrpServerNbmaSubaddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the NBMA subaddress of this server.
For NBMA address families without a subaddress
concept, this will be a zero-length OCTET STRING."
::= { nhrpServerEntry 6 }
Greene, et al. Standards Track [Page 37]RFC 2677 NHRP MIB August 1999
nhrpServerStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object defines whether this row is kept in
volatile storage and lost upon a Server crash or
reboot situation, or if this row is backed up by
nonvolatile or permanent storage."
DEFVAL { nonVolatile }
::= { nhrpServerEntry 7 }
nhrpServerRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be
created and deleted using the RowStatus convention."
::= { nhrpServerEntry 8 }
--
-- The Server Cache Table
--
nhrpServerCacheTable OBJECT-TYPE
SYNTAX SEQUENCE OF NhrpServerCacheEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table extends the nhrpCacheTable for
NHSes. If the nhrpCacheTable has a row added due to
an NHS or based on information regarding an NHS then
a row is also added in this table.
The rows in this table will be created when rows in
the nhrpCacheTable are created. However, there may
be rows created in the nhrpCacheTable which do not
have corresponding rows in this table. For example,
if the nhrpCacheTable has a row added due to a Next
Hop Client which is co-resident on the same device
as the NHS, a row will not be added to this table."
::= { nhrpServerObjects 2 }
nhrpServerCacheEntry OBJECT-TYPE
SYNTAX NhrpServerCacheEntry
MAX-ACCESS not-accessible
STATUS current
Greene, et al. Standards Track [Page 38]RFC 2677 NHRP MIB August 1999
DESCRIPTION
"Additional information kept by a NHS for a relevant
Next Hop Resolution Cache entry."
INDEX {
nhrpCacheInternetworkAddrType,
nhrpCacheInternetworkAddr,
ifIndex,
nhrpCacheIndex
}
::= { nhrpServerCacheTable 1 }
NhrpServerCacheEntry ::= SEQUENCE {
nhrpServerCacheAuthoritative TruthValue,
nhrpServerCacheUniqueness TruthValue
}
nhrpServerCacheAuthoritative OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An indication of whether this cache entry is
authoritative, which means the entry was added because
of a direct registration request with this server or
by Server Cache Synchronization Protocol (SCSP) from
an authoritative source."
::= { nhrpServerCacheEntry 1 }
nhrpServerCacheUniqueness OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Uniqueness indicator for this cache
entry used in duplicate address detection. This value
cannot be changed after the entry is active."
::= { nhrpServerCacheEntry 2 }
--
-- The NHRP Server->Client Table
--
nhrpServerNhcTable OBJECT-TYPE
SYNTAX SEQUENCE OF NhrpServerNhcEntry
MAX-ACCESS not-accessible
STATUS current
Greene, et al. Standards Track [Page 39]RFC 2677 NHRP MIB August 1999
DESCRIPTION
"A table of NHCs that are available for use by this NHS
(Server)."
REFERENCE
"Section 4 Configuration (Next Hop Servers),
RFC 2332 [17]."
::= { nhrpServerObjects 3 }
nhrpServerNhcEntry OBJECT-TYPE
SYNTAX NhrpServerNhcEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An NHC that may be used by an NHS."
INDEX { nhrpServerIndex, nhrpServerNhcIndex }
::= { nhrpServerNhcTable 1 }
NhrpServerNhcEntry ::= SEQUENCE {
nhrpServerNhcIndex Unsigned32,
nhrpServerNhcPrefixLength Integer32,
nhrpServerNhcInternetworkAddrType AddressFamilyNumbers,
nhrpServerNhcInternetworkAddr NhrpGenAddr,
nhrpServerNhcNbmaAddrType AddressFamilyNumbers,
nhrpServerNhcNbmaAddr NhrpGenAddr,
nhrpServerNhcNbmaSubaddr NhrpGenAddr,
nhrpServerNhcInUse TruthValue,
nhrpServerNhcRowStatus RowStatus
}
nhrpServerNhcIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An identifier for an NHC available to an NHS."
::= { nhrpServerNhcEntry 1 }
nhrpServerNhcPrefixLength OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of bits that define the internetwork
layer prefix associated with the
nhrpServerNhcInternetworkAddr."
::= { nhrpServerNhcEntry 2 }
Greene, et al. Standards Track [Page 40]RFC 2677 NHRP MIB August 1999
nhrpServerNhcInternetworkAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the internetwork layer address of the
NHRP Client represented in this entry. This object
indicates how the value of nhrpServerNhcInternetworkAddr
is to be interpreted."
::= { nhrpServerNhcEntry 3 }
nhrpServerNhcInternetworkAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the internetwork layer address of
the NHRP Client represented by this entry. If this
value is not known, this will be a zero-length
OCTET STRING."
::= { nhrpServerNhcEntry 4 }
nhrpServerNhcNbmaAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the NBMA subnetwork address of the NHRP
Client represented by this entry. This object indicates
how the values of nhrpServerNhcNbmaAddr and
nhrpServerNhcNbmaSubaddr are to be interpreted."
::= { nhrpServerNhcEntry 5 }
nhrpServerNhcNbmaAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The NBMA subnetwork address of the NHC. The type of the
address is indicated by the corresponding value of
nhrpServerNbmaAddrType."
::= { nhrpServerNhcEntry 6 }
nhrpServerNhcNbmaSubaddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
Greene, et al. Standards Track [Page 41]RFC 2677 NHRP MIB August 1999
DESCRIPTION
"The NBMA subaddress of the NHC. For NMBA address familes
that do not have the concept of subaddress, this will
be a zero-length OCTET STRING."
::= { nhrpServerNhcEntry 7 }
nhrpServerNhcInUse OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An indication of whether this NHC is in use by the NHS."
::= { nhrpServerNhcEntry 8 }
nhrpServerNhcRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be
created and deleted using the RowStatus convention."
::= { nhrpServerNhcEntry 9 }
--
-- The Next Hop Server Statistics Table
--
nhrpServerStatTable OBJECT-TYPE
SYNTAX SEQUENCE OF NhrpServerStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Statistics collected by Next Hop Servers."
::= { nhrpServerObjects 4 }
nhrpServerStatEntry OBJECT-TYPE
SYNTAX NhrpServerStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Statistics for a particular NHS. The statistics are
broken into received (Rx), transmitted (Tx)
and forwarded (Fw). Forwarded (Fw) would be done
by a transit NHS."
INDEX { nhrpServerIndex }
::= { nhrpServerStatTable 1 }
Greene, et al. Standards Track [Page 42]RFC 2677 NHRP MIB August 1999
NhrpServerStatEntry ::= SEQUENCE {
nhrpServerStatRxResolveReq Counter32,
nhrpServerStatTxResolveReplyAck Counter32,
nhrpServerStatTxResolveReplyNakProhibited Counter32,
nhrpServerStatTxResolveReplyNakInsufResources Counter32,
nhrpServerStatTxResolveReplyNakNoBinding Counter32,
nhrpServerStatTxResolveReplyNakNotUnique Counter32,
nhrpServerStatRxRegisterReq Counter32,
nhrpServerStatTxRegisterAck Counter32,
nhrpServerStatTxRegisterNakProhibited Counter32,
nhrpServerStatTxRegisterNakInsufResources Counter32,
nhrpServerStatTxRegisterNakAlreadyReg Counter32,
nhrpServerStatRxPurgeReq Counter32,
nhrpServerStatTxPurgeReq Counter32,
nhrpServerStatRxPurgeReply Counter32,
nhrpServerStatTxPurgeReply Counter32,
-- Error Indications
nhrpServerStatRxErrUnrecognizedExtension Counter32,
nhrpServerStatRxErrLoopDetected Counter32,
nhrpServerStatRxErrProtoAddrUnreachable Counter32,
nhrpServerStatRxErrProtoError Counter32,
nhrpServerStatRxErrSduSizeExceeded Counter32,
nhrpServerStatRxErrInvalidExtension Counter32,
nhrpServerStatRxErrInvalidResReplyReceived Counter32,
nhrpServerStatRxErrAuthenticationFailure Counter32,
nhrpServerStatRxErrHopCountExceeded Counter32,
nhrpServerStatTxErrUnrecognizedExtension Counter32,
nhrpServerStatTxErrLoopDetected Counter32,
nhrpServerStatTxErrProtoAddrUnreachable Counter32,
nhrpServerStatTxErrProtoError Counter32,
nhrpServerStatTxErrSduSizeExceeded Counter32,
nhrpServerStatTxErrInvalidExtension Counter32,
nhrpServerStatTxErrAuthenticationFailure Counter32,
nhrpServerStatTxErrHopCountExceeded Counter32,
-- Transit NHS statistics
nhrpServerStatFwResolveReq Counter32,
nhrpServerStatFwResolveReply Counter32,
nhrpServerStatFwRegisterReq Counter32,
nhrpServerStatFwRegisterReply Counter32,
nhrpServerStatFwPurgeReq Counter32,
nhrpServerStatFwPurgeReply Counter32,
nhrpServerStatFwErrorIndication Counter32,
nhrpServerStatDiscontinuityTime TimeStamp
Greene, et al. Standards Track [Page 43]RFC 2677 NHRP MIB August 1999
}
nhrpServerStatRxResolveReq OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Resolution Requests received by this
server.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 1 }
nhrpServerStatTxResolveReplyAck OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of positively acknowledged NHRP
Resolution Replies transmitted by this server.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 2 }
nhrpServerStatTxResolveReplyNakProhibited OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NAKed NHRP Resolution Replies
transmitted by this server with the code
'Administratively Prohibited'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 3 }
Greene, et al. Standards Track [Page 44]RFC 2677 NHRP MIB August 1999
nhrpServerStatTxResolveReplyNakInsufResources OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NAKed NHRP Resolution Replies
transmitted by this server with the code
'Insufficient Resources'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 4 }
nhrpServerStatTxResolveReplyNakNoBinding OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NAKed NHRP Resolution Replies
transmitted by this server with the code
'No Internetworking Layer Address to NBMA
Address Binding Exists'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 5 }
nhrpServerStatTxResolveReplyNakNotUnique OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NAKed NHRP Resolution Replies
transmitted by this server with the code
'Binding Exists But Is Not Unique'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 6 }
Greene, et al. Standards Track [Page 45]RFC 2677 NHRP MIB August 1999
nhrpServerStatRxRegisterReq OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Registration Requests received
by this server.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 7 }
nhrpServerStatTxRegisterAck OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of positively acknowledged NHRP Registration
Replies transmitted by this server.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 8 }
nhrpServerStatTxRegisterNakProhibited OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NAKed NHRP Registration Replies
transmitted by this server with the code
'Administratively Prohibited'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 9 }
Greene, et al. Standards Track [Page 46]RFC 2677 NHRP MIB August 1999
nhrpServerStatTxRegisterNakInsufResources OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NAKed NHRP Registration Replies
transmitted by this server with the code
'Insufficient Resources'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 10 }
nhrpServerStatTxRegisterNakAlreadyReg OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NAKed NHRP Registration Replies
transmitted by this server with the code
'Unique Internetworking Layer Address Already
Registered'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 11 }
nhrpServerStatRxPurgeReq OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Purge Requests received by
this server.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 12 }
Greene, et al. Standards Track [Page 47]RFC 2677 NHRP MIB August 1999
nhrpServerStatTxPurgeReq OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Purge Requests transmitted by this
server.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 13 }
nhrpServerStatRxPurgeReply OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Purge Replies received by this
server.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 14 }
nhrpServerStatTxPurgeReply OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Purge Replies transmitted by
this server.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 15 }
nhrpServerStatRxErrUnrecognizedExtension OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
Greene, et al. Standards Track [Page 48]RFC 2677 NHRP MIB August 1999
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets received
by this server with the error code
'Unrecognized Extension'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 16 }
nhrpServerStatRxErrLoopDetected OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets received
by this server with the error code 'NHRP Loop Detected'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 17 }
nhrpServerStatRxErrProtoAddrUnreachable OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets received
by this server with the error code 'Protocol Address
Unreachable'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
Greene, et al. Standards Track [Page 49]RFC 2677 NHRP MIB August 1999
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 18 }
nhrpServerStatRxErrProtoError OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets received
by this server with the error code 'Protocol Error'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 19 }
nhrpServerStatRxErrSduSizeExceeded OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets received
by this server with the error code 'NHRP SDU Size
Exceeded'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 20 }
nhrpServerStatRxErrInvalidExtension OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
Greene, et al. Standards Track [Page 50]RFC 2677 NHRP MIB August 1999
DESCRIPTION
"The number of NHRP Error Indication packets received
by this server with the error code 'Invalid Extension'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 21 }
nhrpServerStatRxErrInvalidResReplyReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets received
by this server with the error code 'Invalid Resolution
Reply Received'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 22 }
nhrpServerStatRxErrAuthenticationFailure OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets
received by this server with the error code
'Authentication Failure'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 23 }
Greene, et al. Standards Track [Page 51]RFC 2677 NHRP MIB August 1999
nhrpServerStatRxErrHopCountExceeded OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets
received by this server with the error code
'Hop Count Exceeded'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 24 }
nhrpServerStatTxErrUnrecognizedExtension OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets
transmitted by this server with the error code
'Unrecognized Extension'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 25 }
nhrpServerStatTxErrLoopDetected OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets
transmitted by this server with the error code
'NHRP Loop Detected'.
Greene, et al. Standards Track [Page 52]RFC 2677 NHRP MIB August 1999
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 26 }
nhrpServerStatTxErrProtoAddrUnreachable OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets
transmitted by this server with the error code
'Protocol Address Unreachable'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 27 }
nhrpServerStatTxErrProtoError OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets
transmitted by this server with the error
code 'Protocol Error'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 28 }
Greene, et al. Standards Track [Page 53]RFC 2677 NHRP MIB August 1999
nhrpServerStatTxErrSduSizeExceeded OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets
transmitted by this server with the error code
'NHRP SDU Size Exceeded'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 29 }
nhrpServerStatTxErrInvalidExtension OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets
transmitted by this server with the error code
'Invalid Extension'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 30 }
nhrpServerStatTxErrAuthenticationFailure OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets
transmitted by this server with the error code
'Authentication Failure'.
Greene, et al. Standards Track [Page 54]RFC 2677 NHRP MIB August 1999
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 31 }
nhrpServerStatTxErrHopCountExceeded OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets
transmitted by this server with the error
code 'Hop Count Exceeded'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 32 }
nhrpServerStatFwResolveReq OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Resolution Requests
forwarded by this server acting as a transit NHS.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 33 }
nhrpServerStatFwResolveReply OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
Greene, et al. Standards Track [Page 55]RFC 2677 NHRP MIB August 1999
DESCRIPTION
"The number of NHRP Resolution Replies forwarded
by this server acting as a transit NHS.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 34 }
nhrpServerStatFwRegisterReq OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Registration Requests forwarded
by this server acting as a transit NHS.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 35 }
nhrpServerStatFwRegisterReply OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Registration Replies forwarded
by this server acting as a transit NHS.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 36 }
nhrpServerStatFwPurgeReq OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Purge Requests forwarded
by this server acting as a transit NHS.
Greene, et al. Standards Track [Page 56]RFC 2677 NHRP MIB August 1999
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 37 }
nhrpServerStatFwPurgeReply OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Purge Replies forwarded by this
server acting as a transit NHS.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 38 }
nhrpServerStatFwErrorIndication OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Error Indication packets forwarded
by this server acting as a transit NHS.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 39 }
nhrpServerStatDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion at
which any one or more of this Server's counters
suffered a discontinuity. If no such discontinuities
have occurred since the last re-initialization of the
Greene, et al. Standards Track [Page 57]RFC 2677 NHRP MIB August 1999
local management subsystem or the NHRP Server
re-initialization associated with this entry, then
this object contains a zero value."
REFERENCE
"RFC 2233 [18]."
::= { nhrpServerStatEntry 40 }
--****************************************************************
-- Module Compliance Statement
--****************************************************************
nhrpConformance OBJECT IDENTIFIER ::= { nhrpMIB 2 }
nhrpCompliances
OBJECT IDENTIFIER ::= { nhrpConformance 1 }
nhrpGroups
OBJECT IDENTIFIER ::= { nhrpConformance 2 }
nhrpModuleCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for the NHRP MIB."
MODULE -- this module
MANDATORY-GROUPS { nhrpGeneralGroup }
GROUP nhrpClientGroup
DESCRIPTION
"This group must be supported only by stations that
are NHRP clients."
GROUP nhrpServerGroup
DESCRIPTION
"This group must be supported only by stations that
are NHRP servers."
::= { nhrpCompliances 1 }
nhrpGeneralGroup OBJECT-GROUP
OBJECTS {
nhrpNextIndex,
nhrpCachePrefixLength,
nhrpCacheNextHopInternetworkAddr,
nhrpCacheNbmaAddrType,
nhrpCacheNbmaAddr,
nhrpCacheNbmaSubaddr,
nhrpCacheType,
nhrpCacheState,
Greene, et al. Standards Track [Page 58]RFC 2677 NHRP MIB August 1999
nhrpCacheHoldingTimeValid,
nhrpCacheHoldingTime,
nhrpCacheNegotiatedMtu,
nhrpCachePreference,
nhrpCacheStorageType,
nhrpCacheRowStatus,
nhrpPurgeCacheIdentifier,
nhrpPurgePrefixLength,
nhrpPurgeRequestID,
nhrpPurgeReplyExpected,
nhrpPurgeRowStatus
}
STATUS current
DESCRIPTION
"Objects that apply to both NHRP clients and NHRP
servers."
::= { nhrpGroups 1 }
nhrpClientGroup OBJECT-GROUP
OBJECTS {
nhrpClientInternetworkAddrType,
nhrpClientInternetworkAddr,
nhrpClientNbmaAddrType,
nhrpClientNbmaAddr,
nhrpClientNbmaSubaddr,
nhrpClientInitialRequestTimeout,
nhrpClientRegistrationRequestRetries,
nhrpClientResolutionRequestRetries,
nhrpClientPurgeRequestRetries,
nhrpClientDefaultMtu,
nhrpClientHoldTime,
nhrpClientRequestID,
nhrpClientStorageType,
nhrpClientRowStatus,
nhrpClientRegUniqueness,
nhrpClientRegState,
nhrpClientRegRowStatus,
nhrpClientNhsInternetworkAddrType,
nhrpClientNhsInternetworkAddr,
nhrpClientNhsNbmaAddrType,
nhrpClientNhsNbmaAddr,
nhrpClientNhsNbmaSubaddr,
nhrpClientNhsInUse,
nhrpClientNhsRowStatus,
nhrpClientStatTxResolveReq,
nhrpClientStatRxResolveReplyAck,
nhrpClientStatRxResolveReplyNakProhibited,
Greene, et al. Standards Track [Page 59]RFC 2677 NHRP MIB August 1999
nhrpClientStatRxResolveReplyNakInsufResources,
nhrpClientStatRxResolveReplyNakNoBinding,
nhrpClientStatRxResolveReplyNakNotUnique,
nhrpClientStatTxRegisterReq,
nhrpClientStatRxRegisterAck,
nhrpClientStatRxRegisterNakProhibited,
nhrpClientStatRxRegisterNakInsufResources,
nhrpClientStatRxRegisterNakAlreadyReg,
nhrpClientStatRxPurgeReq,
nhrpClientStatTxPurgeReq,
nhrpClientStatRxPurgeReply,
nhrpClientStatTxPurgeReply,
nhrpClientStatTxErrorIndication,
nhrpClientStatRxErrUnrecognizedExtension,
nhrpClientStatRxErrLoopDetected,
nhrpClientStatRxErrProtoAddrUnreachable,
nhrpClientStatRxErrProtoError,
nhrpClientStatRxErrSduSizeExceeded,
nhrpClientStatRxErrInvalidExtension,
nhrpClientStatRxErrAuthenticationFailure,
nhrpClientStatRxErrHopCountExceeded,
nhrpClientStatDiscontinuityTime
}
STATUS current
DESCRIPTION
"Objects that apply only to NHRP clients."
::= { nhrpGroups 2 }
nhrpServerGroup OBJECT-GROUP
OBJECTS {
nhrpServerInternetworkAddrType,
nhrpServerInternetworkAddr,
nhrpServerNbmaAddrType,
nhrpServerNbmaAddr,
nhrpServerNbmaSubaddr,
nhrpServerStorageType,
nhrpServerRowStatus,
nhrpServerCacheAuthoritative,
nhrpServerCacheUniqueness,
nhrpServerNhcPrefixLength,
nhrpServerNhcInternetworkAddrType,
nhrpServerNhcInternetworkAddr,
nhrpServerNhcNbmaAddrType,
nhrpServerNhcNbmaAddr,
nhrpServerNhcNbmaSubaddr,
nhrpServerNhcInUse,
nhrpServerNhcRowStatus,
nhrpServerStatRxResolveReq,
Greene, et al. Standards Track [Page 60]RFC 2677 NHRP MIB August 1999
nhrpServerStatTxResolveReplyAck,
nhrpServerStatTxResolveReplyNakProhibited,
nhrpServerStatTxResolveReplyNakInsufResources,
nhrpServerStatTxResolveReplyNakNoBinding,
nhrpServerStatTxResolveReplyNakNotUnique,
nhrpServerStatRxRegisterReq,
nhrpServerStatTxRegisterAck,
nhrpServerStatTxRegisterNakProhibited,
nhrpServerStatTxRegisterNakInsufResources,
nhrpServerStatTxRegisterNakAlreadyReg,
nhrpServerStatRxPurgeReq,
nhrpServerStatTxPurgeReq,
nhrpServerStatRxPurgeReply,
nhrpServerStatTxPurgeReply,
nhrpServerStatRxErrUnrecognizedExtension,
nhrpServerStatRxErrLoopDetected,
nhrpServerStatRxErrProtoAddrUnreachable,
nhrpServerStatRxErrProtoError,
nhrpServerStatRxErrSduSizeExceeded,
nhrpServerStatRxErrInvalidExtension,
nhrpServerStatRxErrInvalidResReplyReceived,
nhrpServerStatRxErrAuthenticationFailure,
nhrpServerStatRxErrHopCountExceeded,
nhrpServerStatTxErrUnrecognizedExtension,
nhrpServerStatTxErrLoopDetected,
nhrpServerStatTxErrProtoAddrUnreachable,
nhrpServerStatTxErrProtoError,
nhrpServerStatTxErrSduSizeExceeded,
nhrpServerStatTxErrInvalidExtension,
nhrpServerStatTxErrAuthenticationFailure,
nhrpServerStatTxErrHopCountExceeded,
nhrpServerStatFwResolveReq,
nhrpServerStatFwResolveReply,
nhrpServerStatFwRegisterReq,
nhrpServerStatFwRegisterReply,
nhrpServerStatFwPurgeReq,
nhrpServerStatFwPurgeReply,
nhrpServerStatFwErrorIndication,
nhrpServerStatDiscontinuityTime
}
STATUS current
DESCRIPTION
"Objects that apply only to NHRP servers."
::= { nhrpGroups 3 }
END
Greene, et al. Standards Track [Page 61]RFC 2677 NHRP MIB August 1999
5. IANA Considerations
The Internet Assigned Numbers Authority (IANA) has been and continues
to be responsible for maintaining the ADDRESS FAMILY NUMBERS
(http://www.isi.edu/in-notes/iana/assignments/address-family-numbers)
name space assignments. The IANA has placed this list in a MIB
module, such that it may be imported into other MIBs. The motivation
for doing this is to allow MIBs to not have to change when a new
assignment is made to the ADDRESS FAMILY NUMBERS. This is very
similar to the motivation behind the IANAifType-MIB.
Any additions or changes to the list of ADDRESS FAMILY NUMBERS
registered via IANA will be done as they have in the past and this
document does not propose any changes to the ADDRESS FAMILY NUMBERS
other than to place them into a MIB, which can be found via anonymous
FTP at: ftp://ftp.isi.edu/mib/ianaaddressfamilynumbers.mib.
6. Security
There are a number of management objects defined in this MIB that
have a MAX-ACCESS clause of read-write and/or read-create. Such
objects may be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure
environment without proper protection can have a negative effect on
network operations.
The NHRP Protocol, RFC 2332 [17], Section 5.2.4.4 discusses security.
There is an authentication option which should be utilized to
authenticate the source and also provide data integrity to the NHRP
payload. This MIB does not contain any managed objects which
configure or expose security information such as that needed for NHRP
authentication or data integrity.
The following items were deemed to jeopardize security and thus, were
NOT added to this MIB. Items denoted as (configurable) are those
which would need values. Items denoted as (read-only) are those
which would provide information. Although the NHRP Protocol [17],
requires or has this information, exposing it in a MIB would
jeopardize the entire NBMA domain where NHRP was being used.
Therefore, these items have been omitted from the MIB.
Greene, et al. Standards Track [Page 62]
RFC 2677 NHRP MIB August 1999
1. (configurable) enable/disable security
2. (configurable) SPI (security parameter index).
Depending upon the implementation,
there may be multiple SPIs, and these would
be configurable also. For example, if the
implementation switched to a different SPI
after a given time.
3. (configurable) algorithm.
The HMAC-MD5-128 is the default hash algorithm.
4. (configurable) lifetime value in seconds.
5. (read-only) key.
6. (read-only) list of users who have access
to the above information.
7. Intellectual Property
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the
IETF's procedures with respect to rights in standards-track and
standards-related documentation can be found in BCP-11. Copies of
claims of rights made available for publication and any assurances of
licenses to be made available, or the result of an attempt made to
obtain a general license or permission for the use of such
proprietary rights by implementors or users of this specification can
be obtained from the IETF Secretariat.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights which may cover technology that may be required to practice
this standard. Please address the information to the IETF Executive
Director.
8. Acknowledgments
This document is a product of the IETF's Internetworking Over NBMA
Networks (ion) Working Group.
The authors would like to thank Avri Doria (Bytex) for the first
draft of the NHRP MIB and Keith McCloghrie (cisco) and David Horton
(CITR) for their feedback and suggestions. Also, we would like to
thank Naganand Doraswamy (Bay Networks) for assistance with the
"Security Considerations" section.
Greene, et al. Standards Track [Page 63]RFC 2677 NHRP MIB August 1999
9. References
[1] Harrington, D., Presuhn, R. and B. Wijnen, "An Architecture for
Describing SNMP Management Frameworks", RFC 2571, April 1999.
[2] Rose, M. and K. McCloghrie, "Structure and Identification of
Management Information for TCP/IP-based Internets", STD 16, RFC
1155, May 1990.
[3] Rose, M. and K. McCloghrie, "Concise MIB Definitions", STD 16,
RFC 1212, March 1991.
[4] Rose, M., "A Convention for Defining Traps for use with the
SNMP", RFC 1215, March 1991.
[5] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose,
M. and S. Waldbusser, "Structure of Management Information
Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.
[6] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose,
M. and S. Waldbusser, "Textual Conventions for SMIv2", STD 58,
RFC 2579, April 1999.
[7] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose,
M. and S. Waldbusser, "Conformance Statements for SMIv2", STD
58, RFC 2580, April 1999.
[8] Case, J., Fedor, M., Schoffstall, M. and J. Davin, "Simple
Network Management Protocol", STD 15, RFC 1157, May 1990.
[9] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
"Introduction to Community-based SNMPv2", RFC 1901, January
1996.
[10] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Transport
Mappings for Version 2 of the Simple Network Management Protocol
(SNMPv2)", RFC 1906, January 1996.
[11] Case, J., Harrington D., Presuhn R. and B. Wijnen, "Message
Processing and Dispatching for the Simple Network Management
Protocol (SNMP)", RFC 2572, April 1999.
[12] Blumenthal, U. and B. Wijnen, "User-based Security Model (USM)
for version 3 of the Simple Network Management Protocol
(SNMPv3)", RFC 2574, April 1999.
Greene, et al. Standards Track [Page 64]RFC 2677 NHRP MIB August 1999
[13] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Protocol
Operations for Version 2 of the Simple Network Management
Protocol (SNMPv2)", RFC 1905, January 1996.
[14] Levi, D., Meyer, P. and B. Stewart, "SNMPv3 Applications", RFC
2573, April 1999.
[15] Wijnen, B., Presuhn, R. and K. McCloghrie, "View-based Access
Control Model (VACM) for the Simple Network Management Protocol
(SNMP)", RFC 2575, April 1999.
[16] Case, J., Mundy, R., Partain, D. and B. Stewart, "Introduction
to Version 3 of the Internet-standard Network Management
Framework", RFC 2570, April 1999.
[17] Luciani, J. V., Katz, D., Piscitello, D. and B. Cole, "NBMA Next
Hop Resolution Protocol (NHRP)", RFC 2332, December 1997.
[18] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB
using SMIv2", RFC 2233, November 1997.
[19] Tesink, K., Editor, "Definitions of Managed Objects for ATM
Management", RFC 2515, February 1999.
[20] Narten, T. and H. Alvestrand, "Guidelines for Writing an IANA
Considerations Section in RFCs", BCP 26, RFC 2434, October 1998.
[21] Bradner, S., "Key words for use in RFCs to Indicate Requirement
Levels", BCP 14, RFC 2119, March 1997.
[22] Bradner, S., "The Internet Standards Process -- Revision 3", BCP
9, RFC 2026, October 1996.
[23] Cucchiara, J., editor, "Multiprotocol Over ATM Version 1.0 MIB",
af-mpoa-0092.000, ATM Forum, July 1998.
[24] Fredette, A., editor, "Multiprotocol Over ATM Version 1.0",
af-mpoa-0087.000, ATM Forum, May 1997.
[25] Laubach, M., and J. Halpern, "Classical IP and ARP over ATM",
RFC 2225, April 1998.
[26] Greene, M., J. Luciani, K. White and T. Kuo, "Definitions of
Managed Objects for Classical IP and ARP Over ATM Using SMIv2",
RFC 2320, April 1998.
Greene, et al. Standards Track [Page 65]RFC 2677 NHRP MIB August 1999
10. Authors' Addresses
James V. Luciani
Bay Networks
3 Federal Street
Mail Stop: BL3-03
Billerica, MA 01821
Phone: (978) 288-4734
EMail: luciani@baynetworks.com
Maria Greene
Contractor
Xedia, Corp.
119 Russell Dr.
Littleton, MA 01460
EMail: maria@xedia.com
Joan Cucchiara
IronBridge Networks
55 Hayden Ave.
Lexington, MA 02421
Phone: (781) 372-8236
EMail: joan@ironbridgenetworks.com
Greene, et al. Standards Track [Page 66]
RFC 2677 NHRP MIB August 1999
12. Full Copyright Statement
Copyright (C) The Internet Society (1999). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Greene, et al. Standards Track [Page 67]
