Network Working Group E. Davies
Request for Comments: 4890 Consultant
Category: Informational J. Mohacsi
NIIF/HUNGARNET
May 2007
Recommendations for Filtering ICMPv6 Messages in Firewalls
Status of This Memo
This memo provides information for the Internet community. It does
not specify an Internet standard of any kind. Distribution of this
memo is unlimited.
Copyright Notice
Copyright (C) The IETF Trust (2007).
Abstract
In networks supporting IPv6, the Internet Control Message Protocol
version 6 (ICMPv6) plays a fundamental role with a large number of
functions, and a correspondingly large number of message types and
options. ICMPv6 is essential to the functioning of IPv6, but there
are a number of security risks associated with uncontrolled
forwarding of ICMPv6 messages. Filtering strategies designed for the
corresponding protocol, ICMP, in IPv4 networks are not directly
applicable, because these strategies are intended to accommodate a
useful auxiliary protocol that may not be required for correct
functioning.
This document provides some recommendations for ICMPv6 firewall
filter configuration that will allow propagation of ICMPv6 messages
that are needed to maintain the functioning of the network but drop
messages that are potential security risks.
Davies & Mohacsi Informational [Page 1]RFC 4890 ICMPv6 Filtering Recommendations May 2007
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Classifying ICMPv6 Messages . . . . . . . . . . . . . . . . . 6
2.1. Error and Informational ICMPv6 Messages . . . . . . . . . 6
2.2. Addressing of ICMPv6 . . . . . . . . . . . . . . . . . . . 6
2.3. Network Topology and Address Scopes . . . . . . . . . . . 7
2.4. Role in Establishing and Maintaining Communication . . . . 7
3. Security Considerations . . . . . . . . . . . . . . . . . . . 8
3.1. Denial-of-Service Attacks . . . . . . . . . . . . . . . . 9
3.2. Probing . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.3. Redirection Attacks . . . . . . . . . . . . . . . . . . . . 9
3.4. Renumbering Attacks . . . . . . . . . . . . . . . . . . . 10
3.5. Problems Resulting from ICMPv6 Transparency . . . . . . . 10
4. Filtering Recommendations . . . . . . . . . . . . . . . . . . 10
4.1. Common Considerations . . . . . . . . . . . . . . . . . . 11
4.2. Interaction of Link-Local Messages with
Firewall/Routers and Firewall/Bridges . . . . . . . . . . 12
4.3. Recommendations for ICMPv6 Transit Traffic . . . . . . . . 13
4.3.1. Traffic That Must Not Be Dropped . . . . . . . . . . . 14
4.3.2. Traffic That Normally Should Not Be Dropped . . . . . 14
4.3.3. Traffic That Will Be Dropped Anyway -- No Special
Attention Needed . . . . . . . . . . . . . . . . . . . 15
4.3.4. Traffic for Which a Policy Should Be Defined . . . . . 16
4.3.5. Traffic That Should Be Dropped Unless a Good Case
Can Be Made . . . . . . . . . . . . . . . . . . . . . 17
4.4. Recommendations for ICMPv6 Local Configuration Traffic . . 18
4.4.1. Traffic That Must Not Be Dropped . . . . . . . . . . . 18
4.4.2. Traffic That Normally Should Not Be Dropped . . . . . 19
4.4.3. Traffic That Will Be Dropped Anyway -- No Special
Attention Needed . . . . . . . . . . . . . . . . . . . 19
4.4.4. Traffic for Which a Policy Should Be Defined . . . . . 20
4.4.5. Traffic That Should Be Dropped Unless a Good Case
Can Be Made . . . . . . . . . . . . . . . . . . . . . 21
5. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 21
6. References . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6.1. Normative References . . . . . . . . . . . . . . . . . . . 21
6.2. Informative References . . . . . . . . . . . . . . . . . . 22
Appendix A. Notes on Individual ICMPv6 Messages . . . . . . . . . 24
A.1. Destination Unreachable Error Message . . . . . . . . . . 24
A.2. Packet Too Big Error Message . . . . . . . . . . . . . . . 24
A.3. Time Exceeded Error Message . . . . . . . . . . . . . . . 25
A.4. Parameter Problem Error Message . . . . . . . . . . . . . 25
A.5. ICMPv6 Echo Request and Echo Response . . . . . . . . . . 26
A.6. Neighbor Solicitation and Neighbor Advertisement
Messages . . . . . . . . . . . . . . . . . . . . . . . . . 26
A.7. Router Solicitation and Router Advertisement Messages . . 27
A.8. Redirect Messages . . . . . . . . . . . . . . . . . . . . 27
Davies & Mohacsi Informational [Page 2]RFC 4890 ICMPv6 Filtering Recommendations May 2007
A.9. SEND Certificate Path Messages . . . . . . . . . . . . . . 27
A.10. Multicast Listener Discovery Messages . . . . . . . . . . 27
A.11. Multicast Router Discovery Messages . . . . . . . . . . . 28
A.12. Router Renumbering Messages . . . . . . . . . . . . . . . 28
A.13. Node Information Query and Reply . . . . . . . . . . . . . 28
A.14. Mobile IPv6 Messages . . . . . . . . . . . . . . . . . . . 28
A.15. Unused and Experimental Messages . . . . . . . . . . . . . 29
Appendix B. Example Script to Configure ICMPv6 Firewall Rules . . 30
1. Introduction
When a network supports IPv6 [RFC2460], the Internet Control Message
Protocol version 6 (ICMPv6) [RFC4443] plays a fundamental role
including being an essential component in establishing and
maintaining communications both at the interface level and for
sessions to remote nodes. This means that overly aggressive
filtering of ICMPv6 by firewalls may have a detrimental effect on the
establishment and maintenance of IPv6 communications. On the other
hand, allowing indiscriminate passage of all ICMPv6 messages can be a
major security risk. This document recommends a set of rules that
seek to balance effective IPv6 communication against the needs of
site security.
In a few cases, the appropriate rules will depend on whether the
firewall is protecting
o an individual host,
o an end site where all ICMPv6 messages originate or terminate
within the site, or
o a transit site such as an Internet Service Provider's site where
some ICMPv6 messages will be passing through.
The document suggests alternative rules appropriate to each situation
where it is relevant. It also notes some situations where
alternative rules could be adopted according to the nature of the
work being carried out on the site and consequent security policies.
In general, Internet Service Providers should not filter ICMPv6
messages transiting their sites so that all the necessary
communication elements are available to their customers to decide and
filter according to their policy.
Readers familiar with ICMPv6 can skip to the recommended filtering
rules in Section 4 and an example configuration script for Linux
Netfilter in Appendix B.
Davies & Mohacsi Informational [Page 3]RFC 4890 ICMPv6 Filtering Recommendations May 2007
ICMPv6 has a large number of functions defined in a number of sub-
protocols, and there are a correspondingly large number of messages
and options within these messages. The functions currently defined
fall into a number of categories:
Returning Error Messages
* Returning error messages to the source if a packet could not
be delivered. Four different error messages, each with a
number of sub-types, are specified in [RFC4443].
Connection Checking
* Simple monitoring of connectivity through echo requests and
responses used by the ping and traceroute utilities. The
Echo Request and Echo Response messages are specified in
[RFC4443].
Discovery Functions
* Finding neighbors (both routers and hosts) connected to the
same link and determining their IP and link layer addresses.
These messages are also used to check the uniqueness of any
addresses that an interface proposes to use (Duplicate
Address Detection - DAD). Four messages -- Neighbor
Solicitation (NS), Neighbor Advertisement (NA), Router
Solicitation (RS) and Router Advertisement (RA) -- are
specified in [RFC2461].
* Ensuring that neighbors remain reachable using the same IP
and link layer addresses after initial discovery (Neighbor
Unreachability Discovery - NUD) and notifying neighbors of
changes to link layer addresses. Uses NS and NA [RFC2461].
* Finding routers and determining how to obtain IP addresses
to join the subnets supported by the routers. Uses RS and
RA [RFC2461].
* If stateless autoconfiguration of hosts is enabled,
communicating prefixes and other configuration information
(including the link Maximum Transmission Unit (MTU) and
suggested hop limit default) from routers to hosts. Uses RS
and RA [RFC2462].
* When using SEcure Neighbor Discovery (SEND) to authenticate
a router attached to a link, the Certificate Path
Solicitation and Advertisement messages specified in
[RFC3971] are used by hosts to retrieve the certificates
Davies & Mohacsi Informational [Page 4]RFC 4890 ICMPv6 Filtering Recommendations May 2007
documenting the trust chain between a trust anchor and the
router from the router.
* Determining the MTU along a path. The Packet Too Big error
message is essential to this function [RFC1981].
* Providing a means to discover the IPv6 addresses associated
with the link layer address of an interface (the inverse of
Neighbor Discovery, where the link layer address is
discovered given an IPv6 address). Two messages, Inverse
Neighbor Discovery Solicitation and Advertisement messages,
are specified in [RFC3122].
* Communicating which multicast groups have listeners on a
link to the multicast capable routers connected to the link.
Uses messages Multicast Listener Query, Multicast Listener
Report (two versions), and Multicast Listener Done (protocol
version 1 only) as specified in Multicast Listener Discovery
MLDv1 [RFC2710] and MLDv2 [RFC3810].
* Discovering multicast routers attached to the local link.
Uses messages Multicast Router Advertisement, Multicast
Router Solicitation, and Multicast Router Termination as
specified in Multicast Router Discovery [RFC4286].
Reconfiguration Functions
* Redirecting packets to a more appropriate router on the
local link for the destination address or pointing out that
a destination is actually on the local link even if it is
not obvious from the IP address (where a link supports
multiple subnets). The Redirect message is specified in
[RFC2461].
* Supporting renumbering of networks by allowing the prefixes
advertised by routers to be altered. Uses NS, NA, RS and RA
together with the Router Renumbering message specified in
[RFC2894].
Mobile IPv6 Support
* Providing support for some aspects of Mobile IPv6 especially
dealing with the IPv6 Mobile Home Agent functionality
provided in routers and needed to support a Mobile node
homed on the link. The Home Agent Address Discovery Request
and Reply and the Mobile Prefix Solicitation and
Advertisement messages are specified in [RFC3775].
Davies & Mohacsi Informational [Page 5]RFC 4890 ICMPv6 Filtering Recommendations May 2007
Experimental Extensions
* An experimental extension to ICMPv6 specifies the ICMP Node
Information Query and Response messages that can be used to
retrieve some basic information about nodes [RFC4620].
* The SEAmless IP MOBility (SEAMOBY) working group specified a
pair of experimental protocols that use an ICMPv6 message
specified in [RFC4065] to help in locating an access router
and moving the attachment point of a mobile node from one
access router to another.
Many of these messages should only be used in a link-local context
rather than end-to-end, and filters need to be concerned with the
type of addresses in ICMPv6 packets as well as the specific source
and destination addresses.
Compared with the corresponding IPv4 protocol, ICMP, ICMPv6 cannot be
treated as an auxiliary function with packets that can be dropped in
most cases without damaging the functionality of the network. This
means that firewall filters for ICMPv6 have to be more carefully
configured than was the case for ICMP, where typically a small set of
blanket rules could be applied.
2. Classifying ICMPv6 Messages
2.1. Error and Informational ICMPv6 Messages
ICMPv6 messages contain an eight-bit Type field interpreted as an
integer between 0 and 255. Messages with Type values less than or
equal to 127 are Error messages. The remainder are Informational
messages. In general terms, Error messages with well-known
(standardized) Type values would normally be expected to be allowed
to be sent to or pass through firewalls, and may be essential to the
establishment and maintenance of communications (see Section 2.4)
whereas Informational messages will generally be the subject of
policy rules, and those passing through end site firewalls can, in
many but by no means all cases, be dropped without damaging IPv6
communications.
2.2. Addressing of ICMPv6
ICMPv6 messages are sent using various kinds of source and
destination address types and scopes. The source address is usually
a unicast address, but during address autoconfiguration message
exchanges, the unspecified address (::) is also used as a source
address [RFC2462].
Davies & Mohacsi Informational [Page 6]RFC 4890 ICMPv6 Filtering Recommendations May 2007
Multicast Listener Discovery (MLD) Report and Done messages are sent
with a link-local address as the IPv6 source address, if a valid
address is available on the interface. If a valid link-local address
is not available (e.g., one has not been configured), the message is
sent with the unspecified address (::) as the IPv6 source address.
Subsequently, the node will generate new MLD Report messages with
proper link-local source address once it has been configured
[RFC3590].
The destination address can be either a well-known multicast address,
a generated multicast address such as the solicited-node multicast
address, an anycast address, or a unicast address. While many ICMPv6
messages use multicast addresses most of the time, some also use
unicast addresses. For instance, the Router Advertisement messages
are sent to the all-nodes multicast address when unsolicited, but can
also be sent to a unicast address in response to a specific Router
Solicitation, although this is rarely seen in current
implementations.
2.3. Network Topology and Address Scopes
ICMPv6 messages can be classified according to whether they are meant
for end-to-end communications or local communications within a link.
There are also messages that we can classify as 'any-to-end', which
can be sent from any point within a path back to the source;
typically, these are used to announce an error in processing the
original packet. For instance, the address resolution messages are
solely for local communications [RFC2461], whereas the Destination
Unreachable messages are any-to-end in nature. Generally, end-to-end
and any-to-end messages might be expected to pass through firewalls
depending on policies but local communications must not.
Local communications will use link-local addresses in many cases but
may also use global unicast addresses when configuring global
addresses, for example. Also, some ICMPv6 messages used in local
communications may contravene the usual rules requiring compatible
scopes for source and destination addresses.
2.4. Role in Establishing and Maintaining Communication
Many ICMPv6 messages have a role in establishing or maintaining
communications to and from the firewall and such messages have to be
accepted by firewalls for local delivery. Generally, a firewall will
also be acting as a router so that all the messages that might be
used in configuring a router interface need to be accepted and
generated. These messages should not transit through a firewall that
is also acting as a router as they are normally intended for use
within a link.
Davies & Mohacsi Informational [Page 7]
RFC 4890 ICMPv6 Filtering Recommendations May 2007
On the other hand, most ICMPv6 error messages traveling end-to-end or
any-to-end are essential to the establishment and maintenance of
communications. These messages must be passed through firewalls and
might also be sent to and from firewalls to assist with establishment
and maintenance of communications. For example, the Packet Too Big
error message is needed to determine the MTU along a path both when a
communication session is established initially and later if the path
is rerouted during the session.
The remaining ICMPv6 messages that are not associated with
communication establishment or maintenance will normally be
legitimately attempting to pass through a firewall from inside to out
or vice versa, but in most cases decisions as to whether or not to
allow them to pass can be made on the basis of local policy without
interfering with IPv6 communications.
The filtering rules for the various message roles will generally be
different.
3. Security Considerations
This memo recommends filtering configurations for firewalls designed
to minimize the security vulnerabilities that can arise in using the
many different sub-protocols of ICMPv6 in support of IPv6
communication.
A major concern is that it is generally not possible to use IPsec or
other means to authenticate the sender and validate the contents of
many ICMPv6 messages. To a large extent, this is because a site can
legitimately expect to receive certain error and other messages from
almost any location in the wider Internet, and these messages may
occur as a result of the first message sent to a destination.
Establishing security associations with all possible sources of
ICMPv6 messages is therefore impossible.
The inability to establish security associations to protect some
messages that are needed to establish and maintain communications
means that alternative means have to be used to reduce the
vulnerability of sites to ICMPv6-based attacks. The most common way
of doing this is to establish strict filtering policies in site
firewalls to limit the unauthenticated ICMPv6 messages that can pass
between the site and the wider Internet. This makes control of
ICMPv6 filtering a delicate balance between protecting the site by
dropping some of the ICMPv6 traffic passing through the firewall and
allowing enough of the traffic through to make sure that efficient
communication can be established.
Davies & Mohacsi Informational [Page 8]
RFC 4890 ICMPv6 Filtering Recommendations May 2007
SEND [RFC3971] has been specified as a means to improve the security
of local ICMPv6 communications. SEND sidesteps security association
bootstrapping problems that would result if IPsec was used. SEND
affects only link-local messages and does not limit the filtering
that firewalls can apply, and its role in security is therefore not
discussed further in this document.
Firewalls will normally be used to monitor ICMPv6 to control the
following security concerns:
3.1. Denial-of-Service Attacks
ICMPv6 can be used to cause a denial of service (DoS) in a number of
ways, including simply sending excessive numbers of ICMPv6 packets to
destinations in the site and sending error messages that disrupt
established communications by causing sessions to be dropped. Also,
if spurious communication establishment or maintenance messages can
be infiltrated onto a link, it might be possible to invalidate
legitimate addresses or disable interfaces.
3.2. Probing
A major security consideration is preventing attackers from probing
the site to determine the topology and identify hosts that might be
vulnerable to attack. Carefully crafted but, often, malformed
messages can be used to provoke ICMPv6 responses from hosts thereby
informing attackers of potential targets for future attacks.
However, the very large address space of IPv6 makes probing a less
effective weapon as compared with IPv4 provided that addresses are
not allocated in an easily guessable fashion. This subject is
explored in more depth in [SCAN-IMP].
3.3. Redirection Attacks
A redirection attack could be used by a malicious sender to perform
man-in-the-middle attacks or divert packets either to a malicious
monitor or to cause DoS by blackholing the packets. These attacks
would normally have to be carried out locally on a link using the
Redirect message. Administrators need to decide if the improvement
in efficiency from using Redirect messages is worth the risk of
malicious use. Factors to consider include the physical security of
the link and the complexity of addressing on the link. For example,
on an open wireless link, redirection would be a serious hazard due
to the lack of physical security. On the other hand, with a wired
link in a secure building with complex addressing and redundant
routers, the efficiency gains might well outweigh the small risk of a
rogue node being connected.
Davies & Mohacsi Informational [Page 9]
RFC 4890 ICMPv6 Filtering Recommendations May 2007
3.4. Renumbering Attacks
Spurious Renumbering messages can lead to the disruption of a site.
Although Renumbering messages are required to be authenticated with
IPsec, so that it is difficult to carry out such attacks in practice,
they should not be allowed through a site boundary firewall. On the
other hand, a site may employ multiple "layers" of firewalls. In
this case, Renumbering messages might be expected to be allowed to
transit interior firewalls but not pass across the outer boundary.
3.5. Problems Resulting from ICMPv6 Transparency
Because some ICMPv6 error packets need to be passed through a
firewall in both directions, malicious users can potentially use
these messages to communicate between inside and outside, bypassing
administrative inspection. For example, it might be possible to
carry out a covert conversation through the payload of ICMPv6 error
messages or tunnel inappropriate encapsulated IP packets in ICMPv6
error messages. This problem can be alleviated by filtering ICMPv6
errors using a deep packet inspection mechanism to ensure that the
packet carried as a payload is associated with legitimate traffic to
or from the protected network.
4. Filtering Recommendations
When designing firewall filtering rules for ICMPv6, the rules can be
divided into two classes:
o Rules for ICMPv6 traffic transiting the firewall, with some minor
variations for
* firewalls protecting end sites or individual hosts, and
* firewalls protecting transit sites
o Rules for ICMPv6 directed to interfaces on the firewall
Firewalls integrated with an individual host ("end host firewalls")
can be treated as end site firewalls, but the special considerations
discussed in Section 4.2 may be relevant because the firewall is not
a router.
Davies & Mohacsi Informational [Page 10]RFC 4890 ICMPv6 Filtering Recommendations May 2007
This section suggests some common considerations that should be borne
in mind when designing filtering rules and then categorizes the rules
for each class. The categories are:
o Messages that must not be dropped: usually because establishment
or maintenance of communications will be prevented or severely
impacted.
o Messages that should not be dropped: administrators need to have a
very good reason for dropping this category.
o Messages that may be dropped in firewall/routers, but these
messages may already be targeted to drop for other reasons (e.g.,
because they are using link-local addresses) or because the
protocol specification would cause the messages to be rejected if
they had passed through a router. Special considerations apply to
transit traffic if the firewall is not a router as discussed in
Section 4.2.
o Messages that administrators may or may not want to drop depending
on local policy.
o Messages that administrators should consider dropping (e.g., ICMP
node information name lookup queries).
More detailed analysis of each of the message types can be found in
Appendix A.
4.1. Common Considerations
Depending on the classification of the message to be filtered (see
Section 2), ICMPv6 messages should be filtered based on the ICMPv6
type of the message and the type (unicast, multicast, etc.) and scope
(link-local, global unicast, etc.) of source and destination
addresses. In some cases, it may be desirable to filter on the Code
field of ICMPv6 error messages.
Messages that can be authenticated on delivery, probably because they
contain an IPsec AH header or ESP header with authentication, may be
subject to less strict policies than messages that cannot be
authenticated. In the remainder of this section, we are generally
considering what should be configured for unauthenticated messages.
In many cases, it is not realistic to expect more than a tiny
fraction of the messages to be authenticated.
Where messages are not essential to the establishment or maintenance
of communications, local policy can be used to determine whether a
message should be allowed or dropped.
Davies & Mohacsi Informational [Page 11]RFC 4890 ICMPv6 Filtering Recommendations May 2007
Depending on the capabilities of the firewall being configured, it
may be possible for the firewall to maintain state about packets that
may result in error messages being returned or about ICMPv6 packets
(e.g., Echo Requests) that are expected to receive a specific
response. This state may allow the firewall to perform more precise
checks based on this state, and to apply limits on the number of
ICMPv6 packets accepted incoming or outgoing as a result of a packet
traveling in the opposite direction. The capabilities of firewalls
to perform such stateful packet inspection vary from model to model,
and it is not assumed that firewalls are uniformly capable in this
respect.
Firewalls that are able to perform deep packet inspection may be able
to check the header fields in the start of the errored packet that is
carried by ICMPv6 error messages. If the embedded packet has a
source address that does not match the destination of the error
message, the packet can be dropped. This provides a partial defense
against some possible attacks on TCP that use spoofed ICMPv6 error
messages, but the checks can also be carried out at the destination.
For further information on these attacks see [ICMP-ATTACKS].
In general, the scopes of source and destination addresses of ICMPv6
messages should be matched, and packets with mismatched addresses
should be dropped if they attempt to transit a router. However, some
of the address configuration messages carried locally on a link may
legitimately have mismatched addresses. Node implementations must
accept these messages delivered locally on a link, and administrators
should be aware that they can exist.
ICMPv6 messages transiting firewalls inbound to a site may be treated
differently depending on whether they are addressed to a node on the
site or to some other node. For end sites, packets addressed to
nodes not on the site should be dropped, but would generally be
forwarded by firewalls on transit sites.
4.2. Interaction of Link-Local Messages with Firewall/Routers and
Firewall/Bridges
Firewalls can be implemented both as IP routers (firewall/routers)
and as link layer bridges (e.g., Ethernet bridges) that are
transparent to the IP layer although they will actually be inspecting
the IP packets as they pass through (firewall/bridges).
Many of the messages used for establishment and maintenance of
communications on the local link will be sent with link-local
addresses for at least one of their source and destination. Routers
conforming to the IPv6 standards will not forward these packets;
there is no need to configure additional rules to prevent these
Davies & Mohacsi Informational [Page 12]RFC 4890 ICMPv6 Filtering Recommendations May 2007
packets traversing a firewall/router, although administrators may
wish to configure rules that would drop these packets for insurance
and as a means of monitoring for attacks. Also, the specifications
of ICMPv6 messages intended for use only on the local link specify
various measures that would allow receivers to detect if the message
had passed through a router, including:
o Requiring that the hop limit in the IPv6 header is set to 255 on
transmission. Receivers verify that the hop limit is still 255,
to ensure that the packet has not passed through a router.
o Checking that the source address is a link-local unicast address.
Accordingly, it is not essential to configure firewall/router rules
to drop out-of-specification packets of these types. If they have
non-link-local source and destination addresses, allowing them to
traverse the firewall/router, they would be rejected because of the
checks performed at the destination. Again, firewall administrators
may still wish to configure rules to log or drop such out-of-
specification packets.
For firewall/bridges, slightly different considerations apply. The
physical links on either side of the firewall/bridge are treated as a
single logical link for the purposes of IP. Hence, the link local
messages used for discovery functions on the link must be allowed to
transit the transparent bridge. Administrators should ensures that
routers and hosts attached to the link containing the firewall/bridge
are built to the correct specifications so that out-of-specification
packets are actually dropped as described in the earlier part of this
section.
An end host firewall can generally be thought of as a special case of
a firewall/bridge, but the only link-local messages that need to be
allowed through are those directed to the host's interface.
4.3. Recommendations for ICMPv6 Transit Traffic
This section recommends rules that should be applied to ICMPv6
traffic attempting to transit a firewall.
Davies & Mohacsi Informational [Page 13]RFC 4890 ICMPv6 Filtering Recommendations May 2007
4.3.1. Traffic That Must Not Be Dropped
Error messages that are essential to the establishment and
maintenance of communications:
o Destination Unreachable (Type 1) - All codes
o Packet Too Big (Type 2)
o Time Exceeded (Type 3) - Code 0 only
o Parameter Problem (Type 4) - Codes 1 and 2 only
Appendix A.4 suggests some more specific checks that could be
performed on Parameter Problem messages if a firewall has the
necessary packet inspection capabilities.
Connectivity checking messages:
o Echo Request (Type 128)
o Echo Response (Type 129)
For Teredo tunneling [RFC4380] to IPv6 nodes on the site to be
possible, it is essential that the connectivity checking messages are
allowed through the firewall. It has been common practice in IPv4
networks to drop Echo Request messages in firewalls to minimize the
risk of scanning attacks on the protected network. As discussed in
Section 3.2, the risks from port scanning in an IPv6 network are much
less severe, and it is not necessary to filter IPv6 Echo Request
messages.
4.3.2. Traffic That Normally Should Not Be Dropped
Error messages other than those listed in Section 4.3.1:
o Time Exceeded (Type 3) - Code 1
o Parameter Problem (Type 4) - Code 0
Mobile IPv6 messages that are needed to assist mobility:
o Home Agent Address Discovery Request (Type 144)
o Home Agent Address Discovery Reply (Type 145)
o Mobile Prefix Solicitation (Type 146)
o Mobile Prefix Advertisement (Type 147)
Administrators may wish to apply more selective rules as described in
Appendix A.14 depending on whether the site is catering for mobile
nodes that would normally be at home on the site and/or foreign
mobile nodes roaming onto the site.
Davies & Mohacsi Informational [Page 14]
RFC 4890 ICMPv6 Filtering Recommendations May 2007
4.3.3. Traffic That Will Be Dropped Anyway -- No Special Attention
Needed
The messages listed in this section are all involved with local
management of nodes connected to the logical link on which they were
initially transmitted. All these messages should never be propagated
beyond the link on which they were initially transmitted. If the
firewall is a firewall/bridge rather than a firewall/router, these
messages should be allowed to transit the firewall as they would be
intended for establishing communications between the two physical
parts of the link that are bridged into a single logical link.
During normal operations, these messages will have destination
addresses, mostly link local but in some cases global unicast
addresses, of interfaces on the local link. No special action is
needed to filter messages with link-local addresses in a firewall/
router. As discussed in Section 4.1, these messages are specified so
that either the receiver is able to check that the message has not
passed through a router or it will be dropped at the first router it
encounters.
Administrators may also wish to consider providing rules in firewall/
routers to catch illegal packets sent with hop limit = 1 to avoid
ICMPv6 Time Exceeded messages being generated for these packets.
Address Configuration and Router Selection messages (must be received
with hop limit = 255):
o Router Solicitation (Type 133)
o Router Advertisement (Type 134)
o Neighbor Solicitation (Type 135)
o Neighbor Advertisement (Type 136)
o Redirect (Type 137)
o Inverse Neighbor Discovery Solicitation (Type 141)
o Inverse Neighbor Discovery Advertisement (Type 142)
Link-local multicast receiver notification messages (must have link-
local source address):
o Listener Query (Type 130)
o Listener Report (Type 131)
o Listener Done (Type 132)
o Listener Report v2 (Type 143)
Davies & Mohacsi Informational [Page 15]RFC 4890 ICMPv6 Filtering Recommendations May 2007
SEND Certificate Path notification messages (must be received with
hop limit = 255):
o Certificate Path Solicitation (Type 148)
o Certificate Path Advertisement (Type 149)
Multicast Router Discovery messages (must have link-local source
address and hop limit = 1):
o Multicast Router Advertisement (Type 151)
o Multicast Router Solicitation (Type 152)
o Multicast Router Termination (Type 153)
4.3.4. Traffic for Which a Policy Should Be Defined
The message type that the experimental Seamoby protocols are using
will be expected to have to cross site boundaries in normal
operation. Transit sites must allow these messages to transit the
site. End site administrators should determine if they need to
support these experiments and otherwise messages of this type should
be dropped:
o Seamoby Experimental (Type 150)
Error messages not currently defined by IANA:
o Unallocated Error messages (Types 5-99 inclusive and 102-126
inclusive)
The base ICMPv6 specification suggests that error messages that are
not explicitly known to a node should be forwarded and passed to any
higher-level protocol that might be able to interpret them. There is
a small risk that such messages could be used to provide a covert
channel or form part of a DoS attack. Administrators of end sites
should be aware of this and determine whether they wish to allow
these messages through the firewall. Firewalls protecting transit
sites must allow all types of error messages to transit the site but
may adopt different policies for error messages addressed to nodes
within the site.
All informational messages with types not explicitly assigned by
IANA, currently:
o Unallocated Informational messages (Types 154-199 inclusive and
202-254 inclusive).
Note that the base ICMPv6 specification requires that received
informational messages with unknown types must be silently discarded.
Transit sites must allow these messages to transit the site. End
Davies & Mohacsi Informational [Page 16]RFC 4890 ICMPv6 Filtering Recommendations May 2007
site administrators can either adopt a policy of allowing all these
messages through the firewall, relying on end hosts to drop
unrecognized messages, or drop all such messages at the firewall.
Different policies could be adopted for inbound and outbound
messages.
If administrators choose to implement policies that drop currently
unallocated error or informational messages, it is important to
review the set of messages affected in case new message types are
assigned by IANA.
4.3.5. Traffic That Should Be Dropped Unless a Good Case Can Be Made
Node Information enquiry messages should generally not be forwarded
across site boundaries. Some of these messages will be using non-
link-local unicast addresses so that they will not necessarily be
dropped by address scope limiting rules:
o Node Information Query (Type 139)
o Node Information Response (Type 140)
Router Renumbering messages should not be forwarded across site
boundaries. As originally specified, these messages may use a site
scope multicast address or a site local unicast address. They should
be caught by standard rules that are intended to stop any packet with
a multicast site scope or site local destination being forwarded
across a site boundary provided these are correctly configured.
Since site local addresses have now been deprecated, it seems likely
that changes may be made to allow the use of unique local addresses
or global unicast addresses. Should this happen, it will be
essential to explicitly filter these messages at site boundaries. If
a site has internal as well as boundary firewalls, individual
policies should be established for the internal firewalls depending
on whether or not the site wishes to use Router Renumbering:
o Router Renumbering (Type 138)
Messages with types in the experimental allocations:
o Types 100, 101, 200, and 201.
Messages using the extension type numbers until such time as ICMPv6
needs to use such extensions:
o Types 127 and 255.
Davies & Mohacsi Informational [Page 17]
RFC 4890 ICMPv6 Filtering Recommendations May 2007
4.4. Recommendations for ICMPv6 Local Configuration Traffic
This section recommends filtering rules for ICMPv6 traffic addressed
to an interface on a firewall. For a small number of messages, the
desired behavior may differ between interfaces on the site or private
side of the firewall and the those on the public Internet side of the
firewall.
4.4.1. Traffic That Must Not Be Dropped
Error messages that are essential to the establishment and
maintenance of communications:
o Destination Unreachable (Type 1) - All codes
o Packet Too Big (Type 2)
o Time Exceeded (Type 3) - Code 0 only
o Parameter Problem (Type 4) - Codes 1 and 2 only
Connectivity checking messages:
o Echo Request (Type 128)
o Echo Response (Type 129)
As discussed in Section 4.3.1, dropping connectivity checking
messages will prevent the firewall being the destination of a Teredo
tunnel and it is not considered necessary to disable connectivity
checking in IPv6 networks because port scanning is less of a security
risk.
There are a number of other sets of messages that play a role in
configuring the node and maintaining unicast and multicast
communications through the interfaces of a node. These messages must
not be dropped if the node is to successfully participate in an IPv6
network. The exception to this is the Redirect message for which an
explicit policy decision should be taken (see Section 4.4.4).
Address Configuration and Router Selection messages:
o Router Solicitation (Type 133)
o Router Advertisement (Type 134)
o Neighbor Solicitation (Type 135)
o Neighbor Advertisement (Type 136)
o Inverse Neighbor Discovery Solicitation (Type 141)
o Inverse Neighbor Discovery Advertisement (Type 142)
Davies & Mohacsi Informational [Page 18]
RFC 4890 ICMPv6 Filtering Recommendations May 2007
Link-Local Multicast Receiver Notification messages:
o Listener Query (Type 130)
o Listener Report (Type 131)
o Listener Done (Type 132)
o Listener Report v2 (Type 143)
SEND Certificate Path Notification messages:
o Certificate Path Solicitation (Type 148)
o Certificate Path Advertisement (Type 149)
Multicast Router Discovery messages:
o Multicast Router Advertisement (Type 151)
o Multicast Router Solicitation (Type 152)
o Multicast Router Termination (Type 153)
4.4.2. Traffic That Normally Should Not Be Dropped
Error messages other than those listed in Section 4.4.1:
o Time Exceeded (Type 3) - Code 1
o Parameter Problem (Type 4) - Code 0
4.4.3. Traffic That Will Be Dropped Anyway -- No Special Attention
Needed
Router Renumbering messages must be authenticated using IPsec, so it
is not essential to filter these messages even if they are not
allowed at the firewall/router:
o Router Renumbering (Type 138)
Mobile IPv6 messages that are needed to assist mobility:
o Home Agent Address Discovery Request (Type 144)
o Home Agent Address Discovery Reply (Type 145)
o Mobile Prefix Solicitation (Type 146)
o Mobile Prefix Advertisement (Type 147)
It may be desirable to drop these messages, especially on public
interfaces, if the firewall is not also providing mobile home agent
services, but they will be ignored otherwise.
Davies & Mohacsi Informational [Page 19]RFC 4890 ICMPv6 Filtering Recommendations May 2007
The message used by the experimental Seamoby protocols may be dropped
but will be ignored if the service is not implemented:
o Seamoby Experimental (Type 150)
4.4.4. Traffic for Which a Policy Should Be Defined
Redirect messages provide a significant security risk, and
administrators should take a case-by-case approach to whether
firewalls, routers in general, and other nodes should accept these
messages:
o Redirect (Type 137)
Conformant nodes must provide configuration controls that allow nodes
to control their behavior with respect to Redirect messages so that
it should only be necessary to install specific filtering rules under
special circumstances, such as if Redirect messages are accepted on
private interfaces but not public ones.
If a node implements the experimental Node Information service, the
administrator needs to make an explicit decision as to whether the
node should respond to or accept Node Information messages on each
interface:
o Node Information Query (Type 139)
o Node Information Response (Type 140)
It may be possible to disable the service on the node if it is not
wanted, in which case these messages will be ignored and no filtering
is necessary.
Error messages not currently defined by IANA:
o Unallocated Error messages (Types 5-99 inclusive and 102-126
inclusive)
The base ICMPv6 specification suggests that error messages that are
not explicitly known to a node should be forwarded and passed to any
higher-level protocol that might be able to interpret them. There is
a small risk that such messages could be used to provide a covert
channel or form part of a DoS attack. Administrators should be aware
of this and determine whether they wish to allow these messages to be
sent to the firewall.
Davies & Mohacsi Informational [Page 20]RFC 4890 ICMPv6 Filtering Recommendations May 2007
4.4.5. Traffic That Should Be Dropped Unless a Good Case Can Be Made
Messages with types in the experimental allocations:
o Types 100, 101, 200, and 201.
Messages using the extension type numbers until such time as ICMPv6
needs to use such extensions:
o Types 127 and 255.
All informational messages with types not explicitly assigned by
IANA, currently:
o Types 154-199 inclusive and 202-254 inclusive.
Note that the base ICMPv6 specification requires that received
informational messages with unknown types must be silently discarded.
5. Acknowledgements
Pekka Savola created the original IPv6 Security Overview document,
which contained suggestions for ICMPv6 filter setups. This
information has been incorporated into this document. He has also
provided important comments. Some analysis of the classification of
ICMPv6 messages and the term 'any-to-end' were used by Jari Arkko in
a document relating to ICMPv6 and IKE.
The Netfilter configuration script in Appendix B was contributed by
Suresh Krishnan.
6. References
6.1. Normative References
[RFC1981] McCann, J., Deering, S., and J. Mogul, "Path MTU
Discovery for IP version 6", RFC 1981, August 1996.
[RFC2460] Deering, S. and R. Hinden, "Internet Protocol,
Version 6 (IPv6) Specification", RFC 2460,
December 1998.
[RFC2461] Narten, T., Nordmark, E., and W. Simpson, "Neighbor
Discovery for IP Version 6 (IPv6)", RFC 2461,
December 1998.
[RFC2462] Thomson, S. and T. Narten, "IPv6 Stateless Address
Autoconfiguration", RFC 2462, December 1998.
Davies & Mohacsi Informational [Page 21]RFC 4890 ICMPv6 Filtering Recommendations May 2007
[RFC2710] Deering, S., Fenner, W., and B. Haberman, "Multicast
Listener Discovery (MLD) for IPv6", RFC 2710,
October 1999.
[RFC2894] Crawford, M., "Router Renumbering for IPv6",
RFC 2894, August 2000.
[RFC3122] Conta, A., "Extensions to IPv6 Neighbor Discovery for
Inverse Discovery Specification", RFC 3122,
June 2001.
[RFC3590] Haberman, B., "Source Address Selection for the
Multicast Listener Discovery (MLD) Protocol",
RFC 3590, September 2003.
[RFC3775] Johnson, D., Perkins, C., and J. Arkko, "Mobility
Support in IPv6", RFC 3775, June 2004.
[RFC3810] Vida, R. and L. Costa, "Multicast Listener Discovery
Version 2 (MLDv2) for IPv6", RFC 3810, June 2004.
[RFC3971] Arkko, J., Kempf, J., Zill, B., and P. Nikander,
"SEcure Neighbor Discovery (SEND)", RFC 3971,
March 2005.
[RFC4065] Kempf, J., "Instructions for Seamoby and Experimental
Mobility Protocol IANA Allocations", RFC 4065,
July 2005.
[RFC4286] Haberman, B. and J. Martin, "Multicast Router
Discovery", RFC 4286, December 2005.
[RFC4443] Conta, A., Deering, S., and M. Gupta, "Internet
Control Message Protocol (ICMPv6) for the Internet
Protocol Version 6 (IPv6) Specification", RFC 4443,
March 2006.
[RFC4620] Crawford, M. and B. Haberman, "IPv6 Node Information
Queries", RFC 4620, August 2006.
6.2. Informative References
[ICMP-ATTACKS] Gont, F., "ICMP attacks against TCP", Work
in Progress, October 2006.
[RFC3041] Narten, T. and R. Draves, "Privacy Extensions for
Stateless Address Autoconfiguration in IPv6",
RFC 3041, January 2001.
Davies & Mohacsi Informational [Page 22]RFC 4890 ICMPv6 Filtering Recommendations May 2007
[RFC4380] Huitema, C., "Teredo: Tunneling IPv6 over UDP through
Network Address Translations (NATs)", RFC 4380,
February 2006.
[SCAN-IMP] Chown, T., "IPv6 Implications for Network Scanning",
Work in Progress, March 2007.
[netfilter] netfilter.org, "The netfilter.org project",
Firewalling, NAT and Packet Mangling for Linux ,
2006, <http://www.netfilter.org/>.
Davies & Mohacsi Informational [Page 23]RFC 4890 ICMPv6 Filtering Recommendations May 2007
Appendix A. Notes on Individual ICMPv6 Messages
A.1. Destination Unreachable Error Message
Destination Unreachable (Type 1) error messages [RFC4443] are sent
any-to-end between unicast addresses. The message can be generated
from any node that a packet traverses when the node is unable to
forward the packet for any reason except congestion.
Destination Unreachable messages are useful for debugging, but are
also important to speed up cycling through possible addresses, as
they can avoid the need to wait through timeouts and hence can be
part of the process of establishing or maintaining communications.
It is a common practice in IPv4 to refrain from generating ICMP
Destination Unreachable messages in an attempt to hide the networking
topology and/or service structure. The same idea could be applied to
IPv6, but this can slow down connection if a host has multiple
addresses, some of which are deprecated, as they may be when using
privacy addresses [RFC3041]. If policy allows the generation of
ICMPv6 Destination Unreachable messages, it is important that nodes
provide the correct reason code, one of: no route to destination,
administratively prohibited, beyond scope of source address, address
unreachable, port unreachable, source address failed ingress/egress
policy, or reject route to destination.
A.2. Packet Too Big Error Message
Packet Too Big (Type 2) error messages [RFC4443] are sent any-to-end
between unicast addresses. The message can be generated from any
node that a packet traverses on the path when the node is unable to
forward the packet because the packet is too large for the MTU of the
next link. This message is vital to the correct functioning of Path
MTU Discovery and hence is part of the establishment and maintenance
of communications. Since routers are not allowed to fragment
packets, informing sources of the need to fragment large packets is
more important than for IPv4. If these messages are not generated
when appropriate, hosts will continue to send packets that are too
large or may assume that the route is congested. Effectively, parts
of the Internet will become inaccessible.
If a network chooses to generate packets that are no larger than the
Guaranteed Minimum MTU (1280 octets) and the site's links to the
wider Internet have corresponding MTUs, Packet Too Big messages
should not be expected at the firewall and could be dropped if they
arrive.
Davies & Mohacsi Informational [Page 24]
RFC 4890 ICMPv6 Filtering Recommendations May 2007
A.3. Time Exceeded Error Message
Time Exceeded (Type 3) error messages [RFC4443] can occur in two
contexts:
o Code 0 are generated at any node on the path being taken by the
packet and sent, any-to-end between unicast addresses, if the Hop
Limit value is decremented to zero at that node.
o Code 1 messages are generated at the destination node and sent
end-to-end between unicast addresses if all the segments of a
fragmented message are not received within the reassembly time
limit.
Code 0 messages can be needed as part of the establishment of
communications if the path to a particular destination requires an
unusually large number of hops.
Code 1 messages will generally only result from congestion in the
network, and it is less essential to propagate these messages.
A.4. Parameter Problem Error Message
The great majority of Parameter Problem (Type 4) error messages will
be generated by the destination node when processing destination
options and other extension headers, and hence are sent end-to-end
between unicast addresses. Exceptionally, these messages might be
generated by any node on the path if a faulty or unrecognized hop-by-
hop option is included or from any routing waypoint if there are
faulty or unrecognized destination options associated with a Type 0
routing header. In these cases, the message will be sent any-to-end
using unicast source and destination addresses.
Parameter Problem Code 1 (Unrecognized Next Header) and Code 2
(Unrecognized IPv6 Option) messages may result if a node on the path
(usually the destination) is unable to process a correctly formed
extension header or option. If these messages are not returned to
the source, communication cannot be established, as the source would
need to adapt its choice of options probably because the destination
does not implement these capabilities. Hence, these messages need to
be generated and allowed for effective IPv6 communications.
Code 0 (Erroneous Header) messages indicate a malformed extension
header generally as a result of incorrectly generated packets.
Hence, these messages are useful for debugging purposes, but it is
unlikely that a node generating such packets could establish
communications without human intervention to correct the problem.
Davies & Mohacsi Informational [Page 25]RFC 4890 ICMPv6 Filtering Recommendations May 2007
Code 2 messages, only, can be generated for packets with multicast
destination addresses.
It is possible that attackers may seek to probe or scan a network by
deliberately generating packets with unknown extension headers or
options or with faulty headers. If nodes generate Parameter Problem
error messages in all cases and these outgoing messages are allowed
through firewalls, the attacker may be able to identify active
addresses that can be probed further or learn about the network
topology. The vulnerability could be mitigated whilst helping to
establish communications if the firewall was able to examine such
error messages in depth and was configured to only allow Parameter
Problem messages for headers that had been standardized but were not
supported in the protected network. If the network administrator
believes that all nodes in the network support all legitimate
extension headers, then it would be reasonable to drop all outgoing
Parameter Problem messages. Note that this is not a major
vulnerability in a well-designed IPv6 network because of the
difficulties of performing scanning attacks (see Section 3.2).
A.5. ICMPv6 Echo Request and Echo Response
Echo Request (Type 128) uses unicast addresses as source addresses,
but may be sent to any legal IPv6 address, including multicast and
anycast addresses [RFC4443]. Echo Requests travel end-to-end.
Similarly, Echo Responses (Type 129) travel end-to-end and would have
a unicast address as destination and either a unicast or anycast
address as source. They are mainly used in combination for
monitoring and debugging connectivity. Their only role in
establishing communication is that they are required when verifying
connectivity through Teredo tunnels [RFC4380]: Teredo tunneling to
IPv6 nodes on the site will not be possible if these messages are
blocked. It is not thought that there is a significant risk from
scanning attacks on a well-designed IPv6 network (see Section 3.2),
and so connectivity checks should be allowed by default.
A.6. Neighbor Solicitation and Neighbor Advertisement Messages
ICMPv6 Neighbor Solicitation and Neighbor Advertisement (Type 135 and
136) messages are essential to the establishment and maintenance of
communications on the local link. Firewalls need to generate and
accept these messages to allow them to establish and maintain
interfaces onto their connected links.
Davies & Mohacsi Informational [Page 26]
RFC 4890 ICMPv6 Filtering Recommendations May 2007
Note that the address scopes of the source and destination addresses
on Neighbor Solicitations and Neighbor Advertisements may not match.
The exact functions that these messages will be carrying out depends
on the mechanism being used to configure IPv6 addresses on the link
(Stateless, Stateful, or Static configuration).
A.7. Router Solicitation and Router Advertisement Messages
ICMPv6 Router Solicitation and Router Advertisement (Type 133 and
134) messages are essential to the establishment and maintenance of
communications on the local link. Firewalls need to generate (since
the firewall will generally be behaving as a router) and accept these
messages to allow them to establish and maintain interfaces onto
their connected links.
A.8. Redirect Messages
ICMPv6 Redirect Messages (Type 137) are used on the local link to
indicate that nodes are actually link-local and communications need
not go via a router, or to indicate a more appropriate first-hop
router. Although they can be used to make communications more
efficient, they are not essential to the establishment of
communications and may be a security vulnerability, particularly if a
link is not physically secured. Conformant nodes are required to
provide configuration controls that suppress the generation of
Redirect messages and allow them to be ignored on reception. Using
Redirect messages on, for example, a wireless link without link level
encryption/authentication is particularly hazardous because the link
is open to eavesdropping and packet injection.
A.9. SEND Certificate Path Messages
SEND [RFC3971] uses two messages (Certificate Path Solicitation and
Advertisement - Types 148 and 149) sent from nodes to supposed
routers on the same local link to obtain a certificate path that will
allow the node to authenticate the router's claim to provide routing
services for certain prefixes. If a link connected to a firewall/
router is using SEND, the firewall must be able to exchange these
messages with nodes on the link that will use its routing services.
A.10. Multicast Listener Discovery Messages
Multicast Listener Discovery (MLD) version 1 [RFC2710] (Listener
Query, Listener Report, and Listener Done - Types 130, 131, and 132)
and version 2 [RFC3810] (Listener Query and Listener Report version 2
- Types 130 and 143) messages are sent on the local link to
communicate between multicast-capable routers and nodes that wish to
join or leave specific multicast groups. Firewalls need to be able
Davies & Mohacsi Informational [Page 27]
RFC 4890 ICMPv6 Filtering Recommendations May 2007
to generate Listener messages in order to establish communications
and may generate all the messages if they also provide multicast
routing services.
A.11. Multicast Router Discovery Messages
Multicast Router Discovery [RFC4286] (Router Advertisement, Router
Solicitation, and Router Termination - Types 151, 152, and 153)
messages are sent by nodes on the local link to discover multicast-
capable routers on the link, and by multicast-capable routers to
notify other nodes of their existence or change of state. Firewalls
that also act as multicast routers need to process these messages on
their interfaces.
A.12. Router Renumbering Messages
ICMPv6 Router Renumbering (Type 138) command messages can be received
and results messages sent by routers to change the prefixes that they
advertise as part of Stateless Address Configuration [RFC2461],
[RFC2462]. These messages are sent end-to-end to either the all-
routers multicast address (site or local scope) or specific unicast
addresses from a unicast address.
Router Renumbering messages are required to be protected by IPsec
authentication since they could be readily misused by attackers to
disrupt or divert site communications. Renumbering messages should
generally be confined to sites for this reason.
A.13. Node Information Query and Reply
ICMPv6 Node Information Query and Reply (Type 139 and 140) messages
defined in [RFC4620] are sent end-to-end between unicast addresses,
and they can also be sent to link-local multicast addresses. They
can, in theory, be sent from any node to any other, but it would
generally not be desirable for nodes outside the local site to be
able to send queries to nodes within the site. Also, these messages
are not required to be authenticated.
A.14. Mobile IPv6 Messages
Mobile IPv6 [RFC3775] defines four ICMPv6 messages that are used to
support mobile operations: Home Agent Address Discovery Request, Home
Agent Address Discovery Reply, Mobile Prefix Solicitation, and ICMP
Mobile Prefix Advertisement (Type 144, 145, 146, and 147) messages.
These messages are sent end-to-end between unicast addresses of a
mobile node and its home agent. They must be expected to be sent
from outside a site and must traverse site-boundary firewalls to
reach the home agent in order for Mobile IPv6 to function. The two
Davies & Mohacsi Informational [Page 28]
RFC 4890 ICMPv6 Filtering Recommendations May 2007
Mobile prefix messages should be protected by the use of IPsec
authentication.
o If the site provides home agents for mobile nodes, the firewall
must allow incoming Home Agent Address Discovery Request and
Mobile Prefix Solicitation messages, and outgoing Home Agent
Address Discovery Reply and ICMP Mobile Prefix Advertisement
messages. It may be desirable to limit the destination addresses
for the incoming messages to links that are known to support home
agents.
o If the site is prepared to host roaming mobile nodes, the firewall
must allow outgoing Home Agent Address Discovery Request and
Mobile Prefix Solicitation messages, and incoming Home Agent
Address Discovery Reply and ICMP Mobile Prefix Advertisement
messages.
o Administrators may find it desirable to prevent static nodes that
are normally resident on the site from behaving as mobile nodes by
dropping Mobile IPv6 messages from these nodes.
A.15. Unused and Experimental Messages
A large number of ICMPv6 Type values are currently unused. These
values have not had a specific function registered with IANA. This
section describes how to treat messages that attempt to use these
Type values in a way of which the network administrator (and hence
the firewall) is not aware.
[RFC4443] defines a number of experimental Type values for ICMPv6
Error and Informational messages, which could be used in site-
specific ways. These messages should be dropped by transit networks
and at site edges. They should also not be propagated within sites
unless the network administrator is explicitly made aware of usage.
The codes reserved for future extension of the ICMPv6 Type space
should currently be dropped as this functionality is as yet
undefined.
Any ICMPv6 Informational messages of which the firewall is not aware
should be allowed to transit through the firewall but should not be
accepted for local delivery on any of its interfaces.
Unknown ICMPv6 Error messages should be allowed to pass through
transit networks. At end site boundaries any incoming ICMPv6 Error
messages of which the firewall is not aware may be allowed through
the firewall in line with the specification in [RFC4443], which
requests delivery of unknown error messages to higher-layer protocol
Davies & Mohacsi Informational [Page 29]RFC 4890 ICMPv6 Filtering Recommendations May 2007
processes. However, administrators may wish to disallow forwarding
of these incoming messages as a potential security risk. Unknown
outgoing Error messages should be dropped as the administrator should
be aware of all messages that could be generated on the site.
Also, the SEAMOBY working group has had an ICMPv6 message (Type 150)
allocated for experimental use in two protocols. This message is
sent end-to-end and may need to pass through firewalls on sites that
are supporting the experimental protocols.
Appendix B. Example Script to Configure ICMPv6 Firewall Rules
This appendix contains an example script to implement most of the
rules suggested in this document when using the Netfilter packet
filtering system for Linux [netfilter]. When used with IPv6, the
'ip6tables' command is used to configure packet filtering rules for
the Netfilter system. The script is targeted at a simple enterprise
site that may or may not support Mobile IPv6.
#!/bin/bash
# Set of prefixes on the trusted ("inner") side of the firewall
export INNER_PREFIXES="2001:DB8:85::/60"
# Set of hosts providing services so that they can be made pingable
export PINGABLE_HOSTS="2001:DB8:85::/64"
# Configuration option: Change this to 1 if errors allowed only for
# existing sessions
export STATE_ENABLED=0
# Configuration option: Change this to 1 if messages to/from link
# local addresses should be filtered.
# Do not use this if the firewall is a bridge.
# Optional for firewalls that are routers.
export FILTER_LINK_LOCAL_ADDRS=0
# Configuration option: Change this to 0 if the site does not support
# Mobile IPv6 Home Agents - see Appendix A.14
export HOME_AGENTS_PRESENT=1
# Configuration option: Change this to 0 if the site does not support
# Mobile IPv6 mobile nodes being present on the site -
# see Appendix A.14
export MOBILE_NODES_PRESENT=1
ip6tables -N icmpv6-filter
ip6tables -A FORWARD -p icmpv6 -j icmpv6-filter
# Match scope of src and dest else deny
# This capability is not provided for in base ip6tables functionality
# An extension (agr) exists which may support it.
#@TODO@
Davies & Mohacsi Informational [Page 30]RFC 4890 ICMPv6 Filtering Recommendations May 2007
# ECHO REQUESTS AND RESPONSES
# ===========================
# Allow outbound echo requests from prefixes which belong to the site
for inner_prefix in $INNER_PREFIXES
do
ip6tables -A icmpv6-filter -p icmpv6 -s $inner_prefix \
--icmpv6-type echo-request -j ACCEPT
done
# Allow inbound echo requests towards only predetermined hosts
for pingable_host in $PINGABLE_HOSTS
do
ip6tables -A icmpv6-filter -p icmpv6 -d $pingable_host \
--icmpv6-type echo-request -j ACCEPT
done
if [ "$STATE_ENABLED" -eq "1" ]
then
# Allow incoming and outgoing echo reply messages
# only for existing sessions
ip6tables -A icmpv6-filter -m state -p icmpv6 \
--state ESTABLISHED,RELATED --icmpv6-type \
echo-reply -j ACCEPT
else
# Allow both incoming and outgoing echo replies
for pingable_host in $PINGABLE_HOSTS
do
# Outgoing echo replies from pingable hosts
ip6tables -A icmpv6-filter -p icmpv6 -s $pingable_host \
--icmpv6-type echo-reply -j ACCEPT
done
# Incoming echo replies to prefixes which belong to the site
for inner_prefix in $INNER_PREFIXES
do
ip6tables -A icmpv6-filter -p icmpv6 -d $inner_prefix \
--icmpv6-type echo-reply -j ACCEPT
done
fi
# Deny icmps to/from link local addresses
# If the firewall is a router:
# These rules should be redundant as routers should not forward
# link local addresses but to be sure...
# DO NOT ENABLE these rules if the firewall is a bridge
if [ "$FILTER_LINK_LOCAL_ADDRS" -eq "1" ]
then
ip6tables -A icmpv6-filter -p icmpv6 -d fe80::/10 -j DROP
Davies & Mohacsi Informational [Page 31]RFC 4890 ICMPv6 Filtering Recommendations May 2007
ip6tables -A icmpv6-filter -p icmpv6 -s fe80::/10 -j DROP
fi
# Drop echo replies which have a multicast address as a
# destination
ip6tables -A icmpv6-filter -p icmpv6 -d ff00::/8 \
--icmpv6-type echo-reply -j DROP
# DESTINATION UNREACHABLE ERROR MESSAGES
# ======================================
if [ "$STATE_ENABLED" -eq "1" ]
then
# Allow incoming destination unreachable messages
# only for existing sessions
for inner_prefix in $INNER_PREFIXES
do
ip6tables -A icmpv6-filter -m state -p icmpv6 \
-d $inner_prefix \
--state ESTABLISHED,RELATED --icmpv6-type \
destination-unreachable -j ACCEPT
done
else
# Allow incoming destination unreachable messages
for inner_prefix in $INNER_PREFIXES
do
ip6tables -A icmpv6-filter -p icmpv6 -d $inner_prefix \
--icmpv6-type destination-unreachable -j ACCEPT
done
fi
# Allow outgoing destination unreachable messages
for inner_prefix in $INNER_PREFIXES
do
ip6tables -A icmpv6-filter -p icmpv6 -s $inner_prefix \
--icmpv6-type destination-unreachable -j ACCEPT
done
# PACKET TOO BIG ERROR MESSAGES
# =============================
if [ "$STATE_ENABLED" -eq "1" ]
then
# Allow incoming Packet Too Big messages
# only for existing sessions
for inner_prefix in $INNER_PREFIXES
do
ip6tables -A icmpv6-filter -m state -p icmpv6 \
Davies & Mohacsi Informational [Page 32]RFC 4890 ICMPv6 Filtering Recommendations May 2007
-d $inner_prefix \
--state ESTABLISHED,RELATED \
--icmpv6-type packet-too-big \
-j ACCEPT
done
else
# Allow incoming Packet Too Big messages
for inner_prefix in $INNER_PREFIXES
do
ip6tables -A icmpv6-filter -p icmpv6 -d $inner_prefix \
--icmpv6-type packet-too-big -j ACCEPT
done
fi
# Allow outgoing Packet Too Big messages
for inner_prefix in $INNER_PREFIXES
do
ip6tables -A icmpv6-filter -p icmpv6 -s $inner_prefix \
--icmpv6-type packet-too-big -j ACCEPT
done
# TIME EXCEEDED ERROR MESSAGES
# ============================
if [ "$STATE_ENABLED" -eq "1" ]
then
# Allow incoming time exceeded code 0 messages
# only for existing sessions
for inner_prefix in $INNER_PREFIXES
do
ip6tables -A icmpv6-filter -m state -p icmpv6 \
-d $inner_prefix \
--state ESTABLISHED,RELATED --icmpv6-type packet-too-big \
-j ACCEPT
done
else
# Allow incoming time exceeded code 0 messages
for inner_prefix in $INNER_PREFIXES
do
ip6tables -A icmpv6-filter -p icmpv6 -d $inner_prefix \
--icmpv6-type ttl-zero-during-transit -j ACCEPT
done
fi
#@POLICY@
# Allow incoming time exceeded code 1 messages
for inner_prefix in $INNER_PREFIXES
do
Davies & Mohacsi Informational [Page 33]RFC 4890 ICMPv6 Filtering Recommendations May 2007
ip6tables -A icmpv6-filter -p icmpv6 -d $inner_prefix \
--icmpv6-type ttl-zero-during-reassembly -j ACCEPT
done
# Allow outgoing time exceeded code 0 messages
for inner_prefix in $INNER_PREFIXES
do
ip6tables -A icmpv6-filter -p icmpv6 -s $inner_prefix \
--icmpv6-type ttl-zero-during-transit -j ACCEPT
done
#@POLICY@
# Allow outgoing time exceeded code 1 messages
for inner_prefix in $INNER_PREFIXES
do
ip6tables -A icmpv6-filter -p icmpv6 -s $inner_prefix \
--icmpv6-type ttl-zero-during-reassembly -j ACCEPT
done
# PARAMETER PROBLEM ERROR MESSAGES
# ================================
if [ "$STATE_ENABLED" -eq "1" ]
then
# Allow incoming parameter problem code 1 and 2 messages
# for an existing session
for inner_prefix in $INNER_PREFIXES
do
ip6tables -A icmpv6-filter -m state -p icmpv6 \
-d $inner_prefix \
--state ESTABLISHED,RELATED --icmpv6-type \
unknown-header-type \
-j ACCEPT
ip6tables -A icmpv6-filter -m state -p icmpv6 \
-d $inner_prefix \
--state ESTABLISHED,RELATED \
--icmpv6-type unknown-option \
-j ACCEPT
done
fi
# Allow outgoing parameter problem code 1 and code 2 messages
for inner_prefix in $INNER_PREFIXES
do
ip6tables -A icmpv6-filter -p icmpv6 -s $inner_prefix \
--icmpv6-type unknown-header-type -j ACCEPT
ip6tables -A icmpv6-filter -p icmpv6 -s $inner_prefix \
Davies & Mohacsi Informational [Page 34]RFC 4890 ICMPv6 Filtering Recommendations May 2007
--icmpv6-type unknown-option -j ACCEPT
done
#@POLICY@
# Allow incoming and outgoing parameter
# problem code 0 messages
for inner_prefix in $INNER_PREFIXES
do
ip6tables -A icmpv6-filter -p icmpv6 \
--icmpv6-type bad-header \
-j ACCEPT
done
# NEIGHBOR DISCOVERY MESSAGES
# ===========================
# Drop NS/NA messages both incoming and outgoing
ip6tables -A icmpv6-filter -p icmpv6 \
--icmpv6-type neighbor-solicitation -j DROP
ip6tables -A icmpv6-filter -p icmpv6 \
--icmpv6-type neighbor-advertisement -j DROP
# Drop RS/RA messages both incoming and outgoing
ip6tables -A icmpv6-filter -p icmpv6 \
--icmpv6-type router-solicitation -j DROP
ip6tables -A icmpv6-filter -p icmpv6 \
--icmpv6-type router-advertisement -j DROP
# Drop Redirect messages both incoming and outgoing
ip6tables -A icmpv6-filter -p icmpv6 --icmpv6-type redirect -j DROP
# MLD MESSAGES
# ============
# Drop incoming and outgoing
# Multicast Listener queries (MLDv1 and MLDv2)
ip6tables -A icmpv6-filter -p icmpv6 --icmpv6-type 130 -j DROP
# Drop incoming and outgoing Multicast Listener reports (MLDv1)
ip6tables -A icmpv6-filter -p icmpv6 --icmpv6-type 131 -j DROP
# Drop incoming and outgoing Multicast Listener Done messages (MLDv1)
ip6tables -A icmpv6-filter -p icmpv6 --icmpv6-type 132 -j DROP
# Drop incoming and outgoing Multicast Listener reports (MLDv2)
ip6tables -A icmpv6-filter -p icmpv6 --icmpv6-type 143 -j DROP
# ROUTER RENUMBERING MESSAGES
Davies & Mohacsi Informational [Page 35]RFC 4890 ICMPv6 Filtering Recommendations May 2007
# ===========================
# Drop router renumbering messages
ip6tables -A icmpv6-filter -p icmpv6 --icmpv6-type 138 -j DROP
# NODE INFORMATION QUERIES
# ========================
# Drop node information queries (139) and replies (140)
ip6tables -A icmpv6-filter -p icmpv6 --icmpv6-type 139 -j DROP
ip6tables -A icmpv6-filter -p icmpv6 --icmpv6-type 140 -j DROP
# MOBILE IPv6 MESSAGES
# ====================
# If there are mobile ipv6 home agents present on the
# trusted side allow
if [ "$HOME_AGENTS_PRESENT" -eq "1" ]
then
for inner_prefix in $INNER_PREFIXES
do
#incoming Home Agent address discovery request
ip6tables -A icmpv6-filter -p icmpv6 -d $inner_prefix \
--icmpv6-type 144 -j ACCEPT
#outgoing Home Agent address discovery reply
ip6tables -A icmpv6-filter -p icmpv6 -s $inner_prefix \
--icmpv6-type 145 -j ACCEPT
#incoming Mobile prefix solicitation
ip6tables -A icmpv6-filter -p icmpv6 -d $inner_prefix \
--icmpv6-type 146 -j ACCEPT
#outgoing Mobile prefix advertisement
ip6tables -A icmpv6-filter -p icmpv6 -s $inner_prefix \
--icmpv6-type 147 -j ACCEPT
done
fi
# If there are roaming mobile nodes present on the
# trusted side allow
if [ "$MOBILE_NODES_PRESENT" -eq "1" ]
then
for inner_prefix in $INNER_PREFIXES
do
#outgoing Home Agent address discovery request
ip6tables -A icmpv6-filter -p icmpv6 -s $inner_prefix \
--icmpv6-type 144 -j ACCEPT
#incoming Home Agent address discovery reply
ip6tables -A icmpv6-filter -p icmpv6 -d $inner_prefix \
Davies & Mohacsi Informational [Page 36]RFC 4890 ICMPv6 Filtering Recommendations May 2007
--icmpv6-type 145 -j ACCEPT
#outgoing Mobile prefix solicitation
ip6tables -A icmpv6-filter -p icmpv6 -s $inner_prefix \
--icmpv6-type 146 -j ACCEPT
#incoming Mobile prefix advertisement
ip6tables -A icmpv6-filter -p icmpv6 -d $inner_prefix \
--icmpv6-type 147 -j ACCEPT
done
fi
# DROP EVERYTHING ELSE
# ====================
ip6tables -A icmpv6-filter -p icmpv6 -j DROP
Example Netfilter Configuration Script for ICMPv6 Filtering
Authors' Addresses
Elwyn B. Davies
Consultant
Soham, Cambs
UK
Phone: +44 7889 488 335
EMail: elwynd@dial.pipex.com
Janos Mohacsi
NIIF/HUNGARNET
Victor Hugo u. 18-22
Budapest, H-1132
Hungary
Phone: +36 1 4503070
EMail: mohacsi@niif.hu
Davies & Mohacsi Informational [Page 37]RFC 4890 ICMPv6 Filtering Recommendations May 2007
Full Copyright Statement
Copyright (C) The IETF Trust (2007).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Davies & Mohacsi Informational [Page 38]
