Internet Engineering Task Force (IETF) A. Melnikov
Request for Comments: 6477 Isode Ltd
Category: Informational G. Lunt
ISSN: 2070-1721 SMHS Ltd
January 2012
Registration of Military Message Handling System (MMHS)
Header Fields for Use in Internet Mail
Abstract
A Military Message Handling System (MMHS) processes formal messages
ensuring release, distribution, security, and timely delivery across
national and international strategic and tactical networks. The MMHS
Elements of Service are defined as a set of extensions to the ITU-T
X.400 (1992) international standards and are specified in STANAG 4406
Edition 2 and ACP 123. This document specifies message header fields
and associated processing for RFC 5322 (Internet Message Format) to
provide a comparable messaging service. In addition, this document
provides for a STANAG 4406 / Internet Email Gateway that supports
message conversion.
Status of This Memo
This document is not an Internet Standards Track specification; it is
published for informational purposes.
This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Not all documents
approved by the IESG are a candidate for any level of Internet
Standard; see Section 2 of RFC 5741.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
http://www.rfc-editor.org/info/rfc6477.
Copyright Notice
Copyright (c) 2012 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
Melnikov & Lunt Informational [Page 1]RFC 6477 MMHS Header Fields January 2012
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction ....................................................2
2. Conventions Used in This Document ...............................3
3. Registration Templates ..........................................3
3.1. Header Field: MMHS-Exempted-Address ........................5
3.2. Header Field: MMHS-Extended-Authorisation-Info .............5
3.3. Header Field: MMHS-Subject-Indicator-Codes .................6
3.4. Header Field: MMHS-Handling-Instructions ...................6
3.5. Header Field: MMHS-Message-Instructions ....................7
3.6. Header Field: MMHS-Codress-Message-Indicator ...............8
3.7. Header Field: MMHS-Originator-Reference ....................8
3.8. Header Field: MMHS-Primary-Precedence ......................9
3.9. Header Field: MMHS-Copy-Precedence ........................10
3.10. Header Field: MMHS-Message-Type ..........................10
3.11. Header Field: MMHS-Other-Recipients-Indicator-To .........11
3.12. Header Field: MMHS-Other-Recipients-Indicator-CC .........12
3.13. Header Field: MMHS-Acp127-Message-Identifier .............13
3.14. Header Field: MMHS-Originator-PLAD .......................13
4. Formal Syntax ..................................................14
5. Service in Comparison to ACP 123 / STANAG 4406 .................16
6. Gatewaying with ACP 123 / STANAG 4406 ..........................16
7. Gatewaying with ACP 127 ........................................18
8. IANA Considerations ............................................18
9. Security Considerations ........................................18
10. References ....................................................19
10.1. Normative References .....................................19
10.2. Informative References ...................................19
Appendix A. Acknowledgements ......................................21
1. Introduction
[RFC5322] defines a protocol for the format of electronic messages
exchanged on the Internet. MMHS is a military specification defined
in ACP 123 [ACP123] (also specified in STANAG 4406 [STANAG-4406]),
which defines a number of extensions to the basic X.400 (1992)
protocol for the services required by military messaging.
This document supports translating most of the Elements of Service
defined in ACP 123 [ACP123] to Internet message header fields (see
Section 5 for more details). This specification is written to extend
the Mime Internet X.400 Enhanced Relay (MIXER) specification
Melnikov & Lunt Informational [Page 2]RFC 6477 MMHS Header Fields January 2012
[RFC2156] to enable inter-conversion in a MIXER gateway with the
X.400 Interpersonal Messaging System (IPMS) heading extensions
defined in ACP 123 / STANAG 4406, Annex A.
The document is aimed at the ability to represent MMHS messages as
RFC 5322 messages. All RFC 5322 header fields defined in this
document are prefixed with the string "MMHS-" to distinguish them
from any other header fields.
Unless stated otherwise, all header fields described in this document
are OPTIONAL in an Internet Message.
This document is structured as follows: Section 3 and its subsections
formally define new Internet header fields and show some examples.
Section 4 provides Augmented Backus-Naur Form (ABNF) syntax for them.
Section 5 provides some background information about which features
of ACP 123 / STANAG 4406 were not implemented in this specification.
Subsequent sections talk about additional requirements for gatewaying
to/from ACP 123 / STANAG 4406 and ACP 127 [ACP127] environments,
respectively.
2. Conventions Used in This Document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
The formal syntax uses the ABNF [RFC5234] notation including the core
rules defined in Appendix B of RFC 5234 [RFC5234].
3. Registration Templates
Header field entries are summarized below in tabular form for
convenience of reference and presented in full in the following
subsections.
Any header field specified in this document MUST NOT appear more than
once in message headers.
Melnikov & Lunt Informational [Page 3]
RFC 6477 MMHS Header Fields January 2012
+------------------------------------+----------+-------------------+
| Header name | Protocol | Reference |
+------------------------------------+----------+-------------------+
| MMHS-Exempted-Address | mail | [ACP123], |
| | | Appendices A1.1 |
| | | and B.105 |
| MMHS-Extended-Authorisation-Info | mail | [ACP123], |
| | | Appendices A1.2 |
| | | and B.106 |
| MMHS-Subject-Indicator-Codes | mail | [ACP123], |
| | | Appendices A1.3 |
| | | and B.107 |
| MMHS-Handling-Instructions | mail | [ACP123][ACP123], |
| | | Appendices A1.4 |
| | | and B.108 |
| MMHS-Message-Instructions | mail | [ACP123], |
| | | Appendices A1.5 |
| | | and B.109 |
| MMHS-Codress-Message-Indicator | mail | [ACP123], |
| | | Appendices A1.6 |
| | | and B.110 |
| MMHS-Originator-Reference | mail | [ACP123], |
| | | Appendices A1.7 |
| | | and B.111 |
| MMHS-Primary-Precedence | mail | [ACP123], |
| | | Appendices A1.8 |
| | | and B.101 |
| MMHS-Copy-Precedence | mail | [ACP123], |
| | | Appendices A1.9 |
| | | and B.102 |
| MMHS-Message-Type | mail | [ACP123], |
| | | Appendices A1.10 |
| | | and B.103 |
| MMHS-Other-Recipients-Indicator-To | mail | [ACP123], |
| | | Appendices A1.12 |
| | | and B.113 |
| MMHS-Other-Recipients-Indicator-CC | mail | [ACP123], |
| | | Appendices A1.12 |
| | | and B.113 |
| MMHS-Acp127-Message-Identifier | mail | [ACP123], |
| | | Appendices A1.14 |
| | | and B.116 |
| MMHS-Originator-PLAD | mail | [ACP123], |
| | | Appendices A1.15 |
| | | and B.117 |
+------------------------------------+----------+-------------------+
Melnikov & Lunt Informational [Page 4]
RFC 6477 MMHS Header Fields January 2012
3.1. Header Field: MMHS-Exempted-Address
Applicable protocol: mail [RFC5322]
Status: informational
Author/change controller: IESG (iesg@ietf.org) on behalf of the IETF
Specification document(s): [RFC6477]
The MMHS-Exempted-Address header field, by its presence, indicates
the addresses of members in an Address List (AL) that should not
receive the message. If this header field is absent from the
message, all members of an AL will be considered to be valid
recipients of the message.
Note: there is no guarantee that the exempted addresses will not
receive the message as the result of redirection, Distribution List
(DL) expansion, etc.
Example:
MMHS-Exempted-Address:
UK SHL CGT Samuals G <graham.samuals@shl.example.com>,
UK SHL Duty Officer <duty@shl.example.com>
3.2. Header Field: MMHS-Extended-Authorisation-Info
Applicable protocol: mail [RFC5322]
Status: informational
Author/change controller: IESG (iesg@ietf.org) on behalf of the IETF
Specification document(s): [RFC6477]]
The MMHS-Extended-Authorisation-Info header field, by its presence,
indicates either the date and the time when the message was
officially released by the releasing officer or the date and time
when the message was initially submitted to a communication facility
for transmission.
This header field SHOULD always be present in an email message that
complies with this specification.
Example:
MMHS-Extended-Authorisation-Info:
Mon, 09 Aug 2010 15:27:40 +0100
The example above demonstrates use of folding white space (FWS
[RFC5322]).
Melnikov & Lunt Informational [Page 5]RFC 6477 MMHS Header Fields January 2012
3.3. Header Field: MMHS-Subject-Indicator-Codes
Applicable protocol: mail [RFC5322]
Status: informational
Author/change controller: IESG (iesg@ietf.org) on behalf of the IETF
Specification document(s): [RFC6477]
A Subject Indicator Code (SIC) is a mechanism for formally
identifying the topic of a message. SICs are nested codes that
provide information for message distribution after delivery to the
recipient organization. SICs are usually three letters or three
letters and digits, but may be up to eight characters long. Nations
and organizations using SICs usually maintain a central registry.
When present, an MMHS-Subject-Indicator-Codes header field contains
one or more SICs, which indicates distribution information to a
recipient or a recipient's User Agent. This information can be used
to perform automatic or manual local distribution of a message. If
the MMHS-Subject-Indicator-Codes header field is absent, then the
local distribution will be in accordance with the message handling
policy of the recipient's domain.
[ACP123] specifies two optional components of the Distribution Code
Element of Service. The MMHS-Subject-Indicator-Codes header field
covers only the SIC code component of distribution codes.
Example:
MMHS-Subject-Indicator-Codes: SDM; KKZ ; BRL
The example above includes three SIC codes: "SDM" (GROUND/LAND
REQUIREMENTS), "KKZ" (HELICOPTER PUBLICATIONS/MANUALS), and "BRL"
(HILEX INCIDENTS).
3.4. Header Field: MMHS-Handling-Instructions
Applicable protocol: mail [RFC5322]
Status: informational
Author/change controller: IESG (iesg@ietf.org) on behalf of the IETF
Specification document(s): [RFC6477]
The MMHS-Handling-Instructions header field, by its presence,
indicates human-readable local handling instructions that require
some manual handling by a traffic operator. If this header field is
absent, the message will be considered as not requiring manual
handling by a traffic operator.
Melnikov & Lunt Informational [Page 6]
RFC 6477 MMHS Header Fields January 2012
Handling instructions (also called "transmission instructions") are a
part of format line 4 as defined in ACP 127 [ACP127] and concern the
sending of the message, e.g., that a particular system shall be used
for transfer of the message.
This header field is used to support interoperability with ACP 127
systems.
Example:
MMHS-Handling-Instructions: RXFPA ZOV MINDEF
The example above includes one ACP 131(F) handling instruction:
"RXFPA ZOV MINDEF". The "ZOV MINDEF" indicates that MINDEF rerouted
the message for some reason, and the correct routing is via RXFPA.
3.5. Header Field: MMHS-Message-Instructions
Applicable protocol: mail [RFC5322]
Status: informational
Author/change controller: IESG (iesg@ietf.org) on behalf of the IETF
Specification document(s): [RFC6477]
The MMHS-Message-Instructions header field, by its presence,
indicates message instructions (also known as "remarks") accompanying
the message (e.g., similar to the operating signals specified in ACP
131 [ACP131]). If this header field is absent, the message will be
considered received without message instructions.
The difference between handling instructions and message instructions
is that the former is only for manual handling by traffic operators,
while the latter also contains information of interest to the persons
reading the message.
Example:
MMHS-Message-Instructions: MINIMIZE CONSIDERED; NO DISTRIBUTION
The example above includes two message instructions defined by
ACP123(B) [ACP123]: "MINIMIZE CONSIDERED" indicating that the
originating user has considered the Minimize status of the recipients
and "NO DISTRIBUTION" indicating that the recipients should not
distribute the message further without the originating user's
approval.
Melnikov & Lunt Informational [Page 7]
RFC 6477 MMHS Header Fields January 2012
3.6. Header Field: MMHS-Codress-Message-Indicator
Applicable protocol: mail [RFC5322]
Status: informational
Author/change controller: IESG (iesg@ietf.org) on behalf of the IETF
Specification document(s): [RFC6477]
The MMHS-Codress-Message-Indicator header field, by its presence,
indicates that the message is in Codress format. If this header
field is absent, the message will be considered received without the
Codress format.
A Codress message is one in which all addresses, i.e., the sender and
all recipients, are encrypted within the ACP 127 text (body)
[ACP127]. The heading of any Codress message contains only the
minimum amount of information that will enable a receiving station to
deal properly and expeditiously with the particular transmission.
The general rules for the preparation and transmission of Codress
messages are given in ACP 121 [ACP121].
This header field is used only to support interoperability with ACP
127 systems.
Example:
MMHS-Codress-Message-Indicator: 23
3.7. Header Field: MMHS-Originator-Reference
Applicable protocol: mail [RFC5322]
Status: informational
Author/change controller: IESG (iesg@ietf.org) on behalf of the IETF
Specification document(s): [RFC6477]
The MMHS-Originator-Reference header field, by its presence,
indicates a user-defined reference called the "originator's number".
If this header field is absent, then the message will be considered
received without any user-defined reference.
The originator's number is used by the originating organizational
unit and is further qualified within national policy.
Note: trailing and leading spaces in an originator reference are not
allowed by syntax.
Example:
MMHS-Originator-Reference: IMSCOM-JIC-612-78
Melnikov & Lunt Informational [Page 8]
RFC 6477 MMHS Header Fields January 2012
3.8. Header Field: MMHS-Primary-Precedence
Applicable protocol: mail [RFC5322]
Status: informational
Author/change controller: IESG (iesg@ietf.org) on behalf of the IETF
Specification document(s): [RFC6477]
The MMHS-Primary-Precedence header field, by its presence, indicates
the precedence level of the primary ("action") recipients. The
message originating domain MUST ensure that this header field is
always present if the message contains "To:" ("action") addresses.
The MMHS Primary Precedence Element of Service indicates the relative
order in which Military Messages are to be handled for primary
(action) recipients, i.e., a Military Message with a higher MMHS-
Primary-Precedence header field value SHOULD be handled before a
Military Message with a lower MMHS-Primary-Precedence header field
value.
The header field value is a non-negative integer, or one of the six
predefined case-insensitive labels: "deferred" (same as "0"),
"routine" (same as "1"), "priority" (same as "2"), "immediate" (same
as "3"), "flash" (same as "4"), or "override" (same as "5"),
optionally followed by a comment. Note that, according to ACP 123,
values in the range from 0 to 15 are reserved for NATO-defined
precedence levels, and values in the range from 16 to 31 are reserved
for national users.
Example 1:
MMHS-Primary-Precedence: 0 (Deferred)
Example 2:
MMHS-Primary-Precedence: FLASH
Example 3:
MMHS-Primary-Precedence: 7
Melnikov & Lunt Informational [Page 9]RFC 6477 MMHS Header Fields January 2012
3.9. Header Field: MMHS-Copy-Precedence
Applicable protocol: mail [RFC5322]
Status: informational
Author/change controller: IESG (iesg@ietf.org) on behalf of the IETF
Specification document(s): [RFC6477]
The MMHS-Copy-Precedence header field, by its presence, indicates the
precedence level of the copy ("information") recipients. The message
originating domain MUST ensure that this header field is always
present if the message contains "Cc:" or "Bcc:" ("information")
addresses.
The MMHS Copy Precedence Element of Service indicates the relative
order in which Military Messages are to be handled for copy
(information) recipients. i.e. a Military Message with higher MMHS-
Copy-Precedence header field value SHOULD be handled before a
Military Message with a lower MMHS-Copy-Precedence header field
value.
The header field value is a non-negative integer, or one of the 6
predefined case-insensitive labels: "deferred" (same as "0"),
"routine" (same as "1"), "priority" (same as "2"), "immediate" (same
as "3"), "flash" (same as "4"), or "override" (same as "5"),
optionally followed by a comment. Note that according to ACP 123,
values in the range from 0 to 15 are reserved for NATO-defined
precedence levels and values in the range from 16 to 31 are reserved
for national users.
Example 1:
MMHS-Copy-Precedence: 2 (priority)
Example 2:
MMHS-Copy-Precedence: Priority
3.10. Header Field: MMHS-Message-Type
Applicable protocol: mail [RFC5322]
Status: informational
Author/change controller: IESG (iesg@ietf.org) on behalf of the IETF
Specification document(s): [RFC6477]
The MMHS-Message-Type heading extension, by its presence, indicates
whether the message is to be considered as an exercise, an operation,
a project, or a drill. (Note that the list of types is extensible,
and other types can be specified using the numeric form, see below).
Melnikov & Lunt Informational [Page 10]RFC 6477 MMHS Header Fields January 2012
It may include an optional parameter specifying the name of the
exercise, operation, project, or drill. If this extension is absent,
the message will be considered to be of an undefined type.
The header field value is a non-negative integer, or one of the four
predefined case-insensitive labels: "exercise" (same as "0"),
"operation" (same as "1"), "project" (same as "2"), "drill" (same as
"3"). Note that according to ACP 123, values in the range from 0 to
127 are reserved for NATO-defined Message Type identifiers and values
in the range from 128 to 255 are not defined by NATO and may be used
nationally or bilaterally.
Example 1:
MMHS-Message-Type: 0(exercise); identifier="CANDLE FISH"
Example 2:
MMHS-Message-Type: 3
Example 3:
MMHS-Message-Type: 2 (projet)
Example 4:
MMHS-Message-Type: project
Note that some of the examples above demonstrate use of optional
comments. See Section 4 for the exact syntax of this header field.
3.11. Header Field: MMHS-Other-Recipients-Indicator-To
Applicable protocol: mail [RFC5322]
Status: informational
Author/change controller: IESG (iesg@ietf.org) on behalf of the IETF
Specification document(s): [RFC6477]
The MMHS-Other-Recipients-Indicator-To header field, by its presence,
indicates the names of primary ("action") recipients that are
intended to receive, or have received, the message via means other
than MMHS. Note that the absence of both this header field and the
MMHS-Other-Recipients-Indicator-CC header field (see Section 3.12)
does not guarantee that all recipients are within the MMHS.
This header field enables a recipient to determine all action
recipients of a Military Message. This header field is derived from
the Other Recipient Indicator Element of Service.
Melnikov & Lunt Informational [Page 11]RFC 6477 MMHS Header Fields January 2012
There are several reasons as to why a recipient of a Military Message
may be identified by this header:
1. The recipient is not part of the MMHS.
2. The path to the recipient through the MMHS may not be secure;
therefore, the originator has used alternative mechanisms to
distribute the Military Message.
3. The recipient was already in receipt of the Military Message
prior to the Military Message being inserted into the MMHS.
Example:
MMHS-Other-Recipients-Indicator-To: UK SHL COS; UK SHL IM
The example above includes names of two primary recipients that
received the message via means other than MMHS.
3.12. Header Field: MMHS-Other-Recipients-Indicator-CC
Applicable protocol: mail [RFC5322]
Status: informational
Author/change controller: IESG (iesg@ietf.org) on behalf of the IETF
Specification document(s): [RFC6477]
The MMHS-Other-Recipients-Indicator-CC header field, by its presence,
indicates the names of copy ("information") recipients that are
intended to receive, or have received, the message via means other
than MMHS. Note that the absence of both this header field and the
MMHS-Other-Recipients-Indicator-To header field (see Section 3.11)
does not guarantee that all recipients are within the MMHS.
This header field enables a recipient to determine all copy
recipients of a Military Message. This header field is derived from
the Other Recipient Indicator Element of Service.
There are several reasons as to why a recipient of a Military Message
may be identified by this header:
1. The recipient is not part of the MMHS.
2. The path to the recipient through the MMHS may not be secure;
therefore, the originator has used alternative mechanisms to
distribute the Military Message.
3. The recipient was already in receipt of the Military Message
prior to it being inserted into the MMHS.
Melnikov & Lunt Informational [Page 12]RFC 6477 MMHS Header Fields January 2012
Example:
MMHS-Other-Recipients-Indicator-CC: UK SHL LEGAD
The example above includes 1 copy (information) recipient that
received the message via means other than MMHS.
3.13. Header Field: MMHS-Acp127-Message-Identifier
Applicable protocol: mail [RFC5322]
Status: informational
Author/change controller: IESG (iesg@ietf.org) on behalf of the IETF
Specification document(s): [RFC6477]
The MMHS-Acp127-Message-Identifier header field, by its presence,
indicates an ACP 127 message identifier [ACP127] for a message that
originated from an ACP 127 domain. If this extension is absent, then
the message did not encounter an ACP 127 domain.
The MMHS-Acp127-Message-Identifier contains the contents of ACP 127
format line 3, which consists of three space-separated fields: the
Calling Station (DERI), Station Serial Number (SSN), and Filing Time
(JFT) [ACP127].
This header field is used only to support interoperability with ACP
127 systems, it should be treated as opaque by a pure MMHS system.
Example:
MMHS-Acp127-Message-Identifier: RPDLE 1234 0341215
3.14. Header Field: MMHS-Originator-PLAD
Applicable protocol: mail [RFC5322]
Status: informational
Author/change controller: IESG (iesg@ietf.org) on behalf of the IETF
Specification document(s): [RFC6477]
The MMHS-Originator-PLAD (PLAD: Plain Language Address Designator)
header field, by its presence, indicates the plain language address
associated with an originator for cross-referencing purposes. If
this header field is absent, then the message will be considered not
to have an originator PLAD cross-reference between the MMHS and ACP
127 domains.
This header field is used only to support interoperability with ACP
127 systems.
Melnikov & Lunt Informational [Page 13]
RFC 6477 MMHS Header Fields January 2012
This header field and the MMHS-Extended-Authorisation-Info header
field provide a cross-reference for message identification in both
ACP 127 and MMHS domains.
Example:
MMHS-Originator-PLAD: SACLANT
4. Formal Syntax
The following syntax specification uses the Augmented Backus-Naur
Form (ABNF) as described in [RFC5234]. Terms not defined here are
taken from [RFC5322], [RFC5234], and [RFC2156].
NZ-DIGIT = %x31-39
; "1".."9"
nonneg-integer = "0" / (NZ-DIGIT *DIGIT)
military-string = 1*69( ps-char )
quoted-military-string = DQUOTE military-string DQUOTE
military-string-sequence = military-string
*( [FWS] ";" [FWS] military-string )
Exempted-Address = "MMHS-Exempted-Address:"
[FWS] address-list [FWS] CRLF
Extended-Authorisation-Info = "MMHS-Extended-Authorisation-Info:"
[FWS] date-time CRLF
Subject-Indicator-Codes = "MMHS-Subject-Indicator-Codes:"
[FWS] sic-sequence [FWS] CRLF
sic-sequence = sic *( [FWS] ";" [FWS] sic )
; ACP 123 specifies that the maximum number of
; SICs is 8. Use of more than 8 SICs is
; permitted, but additional SICs might not
; be transferred to ACP 123 system.
sic = 3*8( ps-char )
Handling-Instructions = "MMHS-Handling-Instructions:"
[FWS] military-string-sequence [FWS] CRLF
Message-Instructions = "MMHS-Message-Instructions:"
[FWS] military-string-sequence [FWS] CRLF
Melnikov & Lunt Informational [Page 14]RFC 6477 MMHS Header Fields January 2012
Codress-Message-Indicator = "MMHS-Codress-Message-Indicator:"
[FWS] nonneg-integer [FWS] CRLF
Originator-Reference = "MMHS-Originator-Reference:"
[FWS] military-string [FWS] CRLF
PrimaryPrecedence = "MMHS-Primary-Precedence:" [FWS] precedence CRLF
CopyPrecedence = "MMHS-Copy-Precedence:" [FWS] precedence CRLF
precedence = (nonneg-integer / std-precedence) [CFWS]
std-precedence = "deferred" / "routine" / "priority" /
"immediate" / "flash" / "override"
; deferred == 0
; routine == 1
; priority == 2
; immediate == 3
; flash == 4
; override == 5
MessageType = "MMHS-Message-Type:" [FWS] message-type [CFWS]
[";" [FWS] MessageTypeParam [FWS] ] CRLF
message-type = nonneg-integer / std-message-type
std-message-type = "exercise" / "operation" / "project" / "drill"
; exercise == 0
; operation == 1
; project == 2
; drill == 3
MessageTypeParam = "identifier" [FWS] "=" [FWS]
quoted-military-string
Designator = military-string
OtherRecipIndicatorPrimary = "MMHS-Other-Recipients-Indicator-To:"
[FWS] Designator *([FWS] ";" [FWS] Designator)
[FWS] CRLF
OtherRecipIndicatorCopy = "MMHS-Other-Recipients-Indicator-CC:"
[FWS] Designator *([FWS] ";" [FWS] Designator)
[FWS] CRLF
Acp127MessageIdentifier = "MMHS-Acp127-Message-Identifier:"
[FWS] military-string [FWS] CRLF
Melnikov & Lunt Informational [Page 15]RFC 6477 MMHS Header Fields January 2012
OriginatorPLAD = "MMHS-Originator-PLAD:" [FWS] military-string [FWS]
CRLF
address-list = <Defined in RFC 5322>
5. Service in Comparison to ACP 123 / STANAG 4406
The service specified in this document is a subset of the
functionality set out in Annex A1 "Military Heading Extensions" of
[ACP123]. The majority of this functionality is supported in this
document. A few capabilities have been left out, which would have
significantly increased the complexity of this specification.
For Distribution Codes (A.1.3) only Subject Indicator Codes are
supported and Distribution Extensions are omitted. Authors of this
document believe that distribution extensions are not widely used.
Address List Indication (A.1.11) is not supported. This complex
extension is deprecated in [ACP123].
Pilot Forwarding Information (A.1.13) is not supported.
Security Information Labels (A.1.16) is not supported. This
extension is deprecated in favor of Annex A of [ACP123], which uses
Enhanced Security Services (ESS) Labels [RFC2634] that can be
supported in a directly compatible manner in S/MIME [RFC5751].
ACP 127 Notification Requests (see Annex A.2.1 of [ACP123) and
Responses (see Annex A.3.1 of [ACP123]) are not supported. These
extensions are used to request and return notifications from ACP 127
gateways, and are not relevant to an SMTP gateway.
6. Gatewaying with ACP 123 / STANAG 4406
The header fields defined in this specification are designed to be
mapped with ACP 123 Annex A1 heading extensions as part of a MIXER
mapping according to [RFC2156]. The syntax of these headings is
defined such that mapping is mechanical. OR Names SHOULD be mapped
with Internet Email addresses according to [RFC2156].
This section summarizes how a gateway between [ACP123] and [RFC5322]
conformant to this specification operates.
If an incoming X.400 message is encoded as P772, [RFC5322] header
fields MUST be generated according to this specification for all ACP
123 heading extensions where an equivalent header is defined in this
specification. For the three heading extensions where no mapping is
defined, the heading extension MAY be discarded or mapped in a
Melnikov & Lunt Informational [Page 16]RFC 6477 MMHS Header Fields January 2012
proprietary manner. If a Distribution Extension is encoded, this MAY
be discarded or represented as a comment (<CFWS>). The whole message
MAY be signed according to [RFC5652]. These rules also apply to
heading extensions in forwarded messages. MM-Message MUST be treated
as a forwarded message for the purposes of MIXER mapping. If an ACP
127 Notification Request is present, this MAY be discarded or
represented as a comment (<CFWS>).
Incoming X.400 notifications are encoded according to [RFC2156]. If
an ACP 127 Notification Response is present, this MAY be discarded or
mapped in a proprietary manner.
If an incoming SMTP message contains any of the header fields defined
in this specification, the outgoing X.400 message MUST be encoded as
P772. The outgoing message MAY be encoded as P772 for other reasons,
for instance, policy or characteristics such as the message
containing a military body part. The X.400 message might be signed
according to ACP 123 Annex B [ACP123] or STANAG 4406 Annex G
[STANAG-4406]. message/rfc822 body parts included in the message
SHOULD be mapped to MM-Message and the heading mapping rules applied.
Generated P772 messages SHOULD follow the following rules, generating
heading extensions if needed.
a. Extended Authorization is required. If the MMHS-Extended-
Authorization-Info header field is absent, then the default value
is taken from the Date header field.
b. Primary Precedence is required if the To header field is present.
If the MMHS-Primary-Precedence header field is absent, the
message need not be considered a Military Message and can be
handled according to a local policy.
c. Copy Precedence is required if the Cc header field is present and
there is an MMHS-Copy-Precedence header field that is different
from the MMHS-Primary-Precedence header field.
d. For Message-ID fields, ACP 123 applies additional constraints
over X.400, leading to the following rules in addition to
[RFC2156], which SHOULD be followed by a gateway following this
specification.
1. The local identifier MUST be at least 15 characters long. If
the [RFC2156] generated value is shorter than this, then it
is padded with spaces to 15 characters. This value will
correctly reverse map.
Melnikov & Lunt Informational [Page 17]RFC 6477 MMHS Header Fields January 2012
2. The OR Address part is required, and it is not usually
generated by an [RFC2156] mapping. It is mandatory in ACP
123. The gateway SHOULD generate an OR Address in a manner
that can be reverse mapped. It MAY use the OR Address to
encode long message ids that cannot be encoded in the local
identifier.
7. Gatewaying with ACP 127
The header fields defined in this specification include fields to
carry Elements of Service specific to ACP 127 [ACP127]. This
specification does not define a mapping of these header fields to ACP
127. In the absence of this mapping, it is recommended that these
headings be mapped to ACP 123 and hence into ACP 127 following the
Annex D (Gateway Translation) of [STANAG-4406].
8. IANA Considerations
IANA has added the list of header fields specified in subsections of
Section 3 to the "Permanent Message Header Field Names" registry
defined by "Registration Procedures for Message Header Fields"
[RFC3864].
9. Security Considerations
Annex B of [ACP123] describes how MMHS messages can be protected in
an X.400 environment. Similar protection can be provided using
S/MIME [RFC5751] and/or DKIM [RFC6376]. In particular, DKIM can be
used to protect against alteration, deletion, or insertion of header
fields specified in this document that can affect disposition and
quality of service applied to processing of the protected Internet
message by receiving gateways/endpoints that support this
specification. (Note that most of the header fields defined in this
document might affect processing of the message by the receiving
gateway/end system, MMHS-Subject-Indicator-Codes and MMHS-Primary-
Precedence/MMHS-Copy-Precedence header fields being the most
important examples. For example, alteration of the MMHS-Primary-
Precedence header field value might affect processing speed of the
message by the recipient Message Transfer Agent (MTA).)
When the original message header fields are digitally signed, the act
of gatewaying messages with such header fields to/from an Internet
environment from/to an ACP 123 environment breaks digital signatures.
The gateway can sign the translated message itself (e.g., with DKIM),
but a message recipient would be unable to verify that the message
was generated by the original sender.
Melnikov & Lunt Informational [Page 18]RFC 6477 MMHS Header Fields January 2012
10. References
10.1. Normative References
[ACP123] CCEB, "Common Messaging Strategy and Procedures", ACP 123
(B), May 2009, http://jcs.dtic.mil/j6/cceb/acps/acp123/.
[ACP127] CCEB, "Communication Instructions - Tape Relay
Procedures", ACP 127 (G), November 1988,
http://jcs.dtic.mil/j6/cceb/acps/acp127/.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2156] Kille, S., "MIXER (Mime Internet X.400 Enhanced Relay):
Mapping between X.400 and RFC 822/MIME", RFC 2156,
January 1998.
[RFC3864] Klyne, G., Nottingham, M., and J. Mogul, "Registration
Procedures for Message Header Fields", BCP 90, RFC 3864,
September 2004.
[RFC5234] Crocker, D., Ed., and P. Overell, "Augmented BNF for
Syntax Specifications: ABNF", STD 68, RFC 5234, January
2008.
[RFC5322] Resnick, P., Ed., "Internet Message Format", RFC 5322,
October 2008.
[RFC5652] Housley, R., "Cryptographic Message Syntax (CMS)", STD
70, RFC 5652, September 2009.
[RFC6376] Crocker, D., Ed., Hansen, T., Ed., and M. Kucherawy, Ed.,
"DomainKeys Identified Mail (DKIM) Signatures", RFC 6376,
September 2011.
10.2. Informative References
[ACP121] CCEB, "Comms Instructions - General", ACP 121 (I),
October 2010, http://jcs.dtic.mil/j6/cceb/acps/acp121/.
[ACP131] CCEB, "Comms Instructions - Operating Signals", ACP 131
(F), April 2009,
http://jcs.dtic.mil/j6/cceb/acps/acp131/.
[RFC2634] Hoffman, P., Ed., "Enhanced Security Services for
S/MIME", RFC 2634, June 1999.
Melnikov & Lunt Informational [Page 19]RFC 6477 MMHS Header Fields January 2012
[RFC5751] Ramsdell, B. and S. Turner, "Secure/Multipurpose Internet
Mail Extensions (S/MIME) Version 3.2 Message
Specification", RFC 5751, January 2010.
[STANAG-4406]
NATO, "STANAG 4406 Edition 2: Military Message Handling
System", STANAG 4406, March 2005.
Melnikov & Lunt Informational [Page 20]RFC 6477 MMHS Header Fields January 2012
Appendix A. Acknowledgements
This document copies a lot of text from the "Mapping between X.400
P772 and RFC-822" by Julian Onions and Graeme Lunt and STANAG 4406
(2nd Edition). So the authors of this document would like to
acknowledge contributions made by the authors of these documents.
Many thanks for reviews and text provided by Steve Kille, Alan Ross,
David Wilson, James Usmar, Kathy Nuckles, Andy Trayler, Ken Carlberg,
Chris Bonatti, Oeyvind Jonsson, Mykyta Yevstifeyev, Sean Turner,
Stephen Farrell, Adrian Farrel, and Peter Saint-Andre.
Authors' Addresses
Alexey Melnikov
Isode Ltd
5 Castle Business Village
36 Station Road
Hampton, Middlesex, TW12 2BX
UK
EMail: Alexey.Melnikov@isode.com
Graeme Lunt
SMHS Ltd
Bescar Moss Farm
Bescar Lane
Ormskirk L40 9QN
UK
EMail: graeme.lunt@smhs.co.uk
Melnikov & Lunt Informational [Page 21]
