Network Working Group K. Lingle
Request for Comments: 4780 Cisco Systems, Inc.
Category: Standards Track J-F. Mule
CableLabs
J. Maeng
D. Walker
April 2007
Management Information Base for
the Session Initiation Protocol (SIP)
Status of This Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The IETF Trust (2007).
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes a set of managed objects that are used to
manage Session Initiation Protocol (SIP) entities, which include User
Agents, and Proxy, Redirect and Registrar servers.
Lingle, et al. Standards Track [Page 1]RFC 4780 SIP MIB Modules April 2007
Table of Contents
1. Introduction ....................................................2
2. Conventions .....................................................2
3. The Internet-Standard Management Framework ......................2
4. Overview ........................................................3
5. Structure of the SIP MIB ........................................3
5.1. Textual Conventions ........................................6
5.2. Relationship to the Network Services MIB ...................6
5.3. IMPORTed MIB Modules and REFERENCE Clauses ................10
6. Accommodating SIP Extension Methods ............................11
7. Definitions ....................................................12
7.1. SIP Textual Conventions ...................................12
7.2. SIP Common MIB Module .....................................15
7.3. SIP User Agent MIB Module .................................55
7.4. SIP Server MIB Module (Proxy, Redirect, and
Registrar Servers) ........................................59
8. IANA Considerations ............................................77
9. Security Considerations ........................................78
10. Contributor Acknowledgments ...................................80
11. References ....................................................80
11.1. Normative References .....................................80
11.2. Informative References ...................................81
1. Introduction
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes a set of managed objects that are used to
manage Session Initiation Protocol (SIP) entities, which include User
Agents, and Proxy, Redirect and Registrar servers. The managed
objects defined in this document are intended to provide basic SIP
protocol management for SIP entities. The management of
application-specific or service-specific SIP configuration is out of
scope.
2. Conventions
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
3. The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Lingle, et al. Standards Track [Page 2]RFC 4780 SIP MIB Modules April 2007
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a set
of MIB modules that are compliant to the SMIv2, which is described in
STD 58, comprised of RFC 2578 [RFC2578], RFC 2579 [RFC2579], and RFC
2580 [RFC2580].
4. Overview
SIP [RFC3261] is an application-layer control (signaling) protocol
for creating, modifying, and terminating sessions with one or more
participants. These sessions include Internet telephone calls,
multimedia distribution, and multimedia conferences.
This MIB provides some managed objects for SIP entities defined in
RFC 3261 [RFC3261] - User Agents (UA), and Proxy, Redirect, and
Registrar servers. It is intended to provide management of the basic
SIP entities. It provides for monitoring of status and protocol
statistics, as well as for configuration of SIP entities.
5. Structure of the SIP MIB
Four MIB modules are specified: SIP-COMMON-MIB, SIP-SERVER-MIB, SIP-
UA-MIB, and SIP-TC-MIB. SIP-COMMON-MIB contains common MIB objects
used in all the SIP entities. SIP-SERVER-MIB contains objects
specific to Proxy, Redirect, and Registrar servers. SIP-UA-MIB
includes objects specific to User Agents. SIP-TC-MIB defines the
textual conventions used throughout the MIB modules.
The MIB modules contain the following groups of objects:
SIP-COMMON-MIB: Management objects common to all the SIP entities
o sipCommonMIBObjects
* sipCommonCfgBase: This object group defines configuration
objects common to all SIP entities, including the SIP protocol
version, the type of SIP entity (UA, proxy, redirect, registrar
servers), the operational and administrative status, the SIP
organization name, the maximum number of SIP transactions an
entity can manage, etc.
* sipCommonCfgTimer: This object group defines timer
configuration objects applicable to SIP user agent and stateful
SIP proxy entities.
Lingle, et al. Standards Track [Page 3]RFC 4780 SIP MIB Modules April 2007
* sipCommonSummaryStats: This object group defines a table
containing the summary statistics objects applicable to all SIP
entities, including the total number of all SIP requests and
responses in/out and the total number of transactions.
* sipCommonMethodStats: This object group defines a table
containing the SIP method statistics objects applicable to all
SIP entities, including the number of outbound and inbound
requests on a per method basis. Retransmissions, where
appropriate, are also included in these statistics.
* sipCommonStatusCode: This object group defines a table
indicating the number of SIP responses (in and out) that the
SIP entity has been requested to monitor on a per-method basis
(100, 200, 302, etc.).
* sipCommonStatsTrans: This object group defines a table
containing a gauge reflecting the number of transactions
currently awaiting definitive responses by the managed SIP
entity.
* sipCommonStatsRetry: This object group defines statistic
objects indicating the number of retransmissions sent on a
per-method basis.
* sipCommonOtherStats: This object group defines additional
statistics objects including the number of SIP requests
received with unsupported URIs, the number of requests received
with unsupported SIP methods, and the number of discarded
messages.
* sipCommonNotifObjects: This object group defines objects
accessible only via a notification (MAX ACCESS clause of
accessible-for-notify): they are related to the SNMP
notifications defined in this MIB module.
The SIP-COMMON-MIB also contains notifications, including:
o sipCommonStatusCodeNotif: indicates that a specific status code
has been sent or received by the system.
o sipCommonStatusCodeThreshExceededNotif: indicates that a specific
status code has been sent or received by the system frequently
enough to exceed the configured threshold.
Lingle, et al. Standards Track [Page 4]RFC 4780 SIP MIB Modules April 2007
SIP-SERVER-MIB: Groups of objects for SIP Proxy, Redirect, and
Registrar servers
o sipServerMIBObjects
* sipServerCfg: This object group defines common server
configuration objects including the SIP server host address.
* sipServerProxyCfg: This object group defines configuration
objects for SIP Proxy Servers including the proxy mode of
operation (stateless, stateful, call stateful), the proxy
authentication method(s), realm, etc.
* sipServerProxyStats: This object group defines a table
containing the statistics objects applicable to SIP Proxy
Servers. It includes the number of occurrences of unsupported
options being specified in received Proxy-Require headers.
* sipServerRegCfg: This object group defines common configuration
objects for SIP Registrar servers, including the ability to
accept third-party registrations, such as the maximum
registration expiry that may be requested by user agents, the
maximum number of users the registrar can support, the number
of currently registered users, per contact registration
information, etc.
* sipServerRegStats: This object group contains summary
statistics objects for SIP Registrar servers. Precisely, it
contains the number of REGISTER requests that have been
accepted or rejected.
SIP-UA-MIB: Group of objects for SIP User Agents
o sipUAMIBObjects
* sipUACfgServer: This object group specifies SIP server
configuration objects applicable to SIP user agents including
the Internet address of the SIP Server the UA uses to register,
proxy, or redirect calls.
To conform with this specification, an SNMP agent MUST implement the
SIP-TC-MIB module, plus the SIP-COMMON-MIB module and one of the SIP
entity-type-specific MIB modules (SIP-SERVER-MIB or SIP-UA-MIB) as
applicable for each instance of a SIP entity being managed. If a
device has more than one SIP entity or multiple instances of the same
entity type, it MUST implement multiple SIP modules. Section 5.2
describes handling of multiple instances in detail.
Lingle, et al. Standards Track [Page 5]RFC 4780 SIP MIB Modules April 2007
5.1. Textual Conventions
The data types SipTCTransportProtocol, SipTCEntityRole,
SipTCOptionTagHeaders, and SipTCMethodName are defined in the SIP-
TC-MIB module and used as Textual Conventions in this document.
5.2. Relationship to the Network Services MIB
In the design of the SIP MIB, the authors considered the following
requirement: the SIP MIB must allow a single system with a single
SNMP agent to support multiple instances of various SIP MIB modules.
This requirement is met by using the framework provided by the
Network Services Monitoring MIB, NETWORK-SERVICES-MIB, RFC 2788
[RFC2788].
A device implementing the SIP MIB MUST support the NETWORK-SERVICES-
MIB and, at a minimum, MUST support the index and name objects
(applIndex and applName) in the application table (applTable). In
order to allow each instance of a SIP entity to be managed as a
separate network service application, a naming convention SHOULD be
used to make the application name unique. For example, if a system
is running 2 SIP UAs that need to be managed as 2 separate SIP
entities, by convention, the application names used in the Network
Services Monitoring MIB application table should be "sip_ua1" and
"sip_ua2". This convention allows each instance to have its own row
in the application table (applTable).
It is therefore RECOMMENDED that the following application name
conventions be adopted:
o for a SIP Proxy entity, the applName value SHOULD be equal to a
character string starting with "sip_proxy" followed by a unique
application instance identifier, for example, "sip_proxy1",
"sip_proxy17".
o for a SIP Registrar entity, the applName value SHOULD be equal to
a character string starting with "sip_registrar" followed by a
unique application instance identifier, for example,
"sip_registrar1", "sip_registrar2".
o for a SIP User Agent entity, the applName value SHOULD be equal to
a character string starting with "sip_ua" followed by a unique
application instance identifier, for example, "sip_ua1",
"sip_ua2".
Lingle, et al. Standards Track [Page 6]RFC 4780 SIP MIB Modules April 2007
o for any combination of Proxy, Registrar, or Redirect Server being
managed as a single aggregate entity, the applName value for the
combined server entity SHOULD reflect the appropriate combination
followed by a unique application instance identifier. In order to
facilitate consistent agent behavior and management application
expectations, the following order of names is RECOMMENDED:
* if Proxy exists, list first.
* if Proxy and Redirect exists, list Redirect second.
* if Registrar exists, always list last.
For example "sip_proxy1", "sip_proxy_registrar1",
"sip_proxy_redirect5", "sip_proxy_redirect_registrar2", or
"sip_registrar1".
o Note: the value of the network service application index
(applIndex) may be different from the instance identifier used in
the system (the applIndex is dynamically created and is the value
assigned by the SNMP agent at the creation of the table entry,
whereas the value of the instance identifier to be used in the
application name is provided as part of the application name
applName by the system administrator or configuration files of the
SIP entity). This note is illustrated in the first example
provided below.
Finally, the SNMP agent MAY support any combination of the other
attributes in applTable. If supported, the following objects SHOULD
have values populated as follows:
o applVersion: version of the SIP application.
o applUptime: the value of applUptime MUST be identical to the value
of sipCommonCfgServiceStartTime defined in the SIP-COMMON-MIB
module.
o applOperStatus: the value of applOperStatus SHOULD reflect the
operational status of sipCommonCfgServiceOperStatus, at least by
means of a mapping.
o applLastChange: the value of applLastChange MUST be identical to
the value of sipCommonCfgServiceLastChange defined in the SIP-
COMMON module.
A number of other objects are defined as part of the applTable. They
are not included for the sake of brevity and due to the fact that
they do not enhance the concept being presented.
Lingle, et al. Standards Track [Page 7]RFC 4780 SIP MIB Modules April 2007
Example 1:
The tables below illustrate how a system acting as both Proxy and
Registrar server might be configured to maintain separate SIP-
COMMON-MIB instances.
The NETWORK-SERVICES-MIB applTable might be populated as follows:
+-----------+-------------------+----------------------+
| applIndex | applName | applDescription |
+-----------+-------------------+----------------------+
| 1 | "sip_proxy10" | "ACME SIP Proxy" |
| 2 | "sip_registrar17" | "ACME SIP Registrar" |
+-----------+-------------------+----------------------+
The SIP-COMMON-MIB sipCommonCfgTable would have two rows: one for the
proxy (applIndex=1) and one for the registrar (applIndex=2). The
SIP-SERVER-MIB tables would, however, only be populated with one row
indexed by applIndex=1 and applIndex=2, respectively, if the server
provides either proxy or registrar.
The SIP-COMMON-MIB sipCommonCfgTable might be populated as:
+---------+------------------------+--------------------------+-----+
|applIndex| sipCommonCfgProtocol | sipCommonCfgServiceOper | ... |
| | Version | Status | |
+---------+------------------------+--------------------------+-----+
| 1 | "SIP/2.0" | up(1) | |
| 2 | "SIP/2.0" | restarting(4) | |
+---------+------------------------+--------------------------+-----+
while the sipServerProxyCfgTable in SIP-SERVER-MIB might be populated
as:
+-----------+-------------------------------+-----+
| applIndex | sipServerCfgProxyStatefulness | ... |
+-----------+-------------------------------+-----+
| 1 | stateless(1) | |
+-----------+-------------------------------+-----+
Lingle, et al. Standards Track [Page 8]RFC 4780 SIP MIB Modules April 2007
and the sipServerRegUserTable in SIP-SERVER-MIB might be populated
as:
+-----------+-----------------------+---------------------+-----+
| applIndex | sipServerRegUserIndex | sipServerRegUserUri | ... |
+-----------+-----------------------+---------------------+-----+
| 2 | 1 | bob@example.com | |
| 2 | 2 | alice@example.com | |
| 2 | 3 | jim@example.com | |
| 2 | 4 | john@example.com | |
+-----------+-----------------------+---------------------+-----+
Example 2:
This example illustrates how to represent a system acting as both
Proxy and Registrar server, where the two entities share a single
instance of SIP-COMMON-MIB.
The NETWORK-SERVICES-MIB applTable might be populated as follows:
+-----------+------------------------+------------------------------+
| applIndex | applName | applDescription |
+-----------+------------------------+------------------------------+
| 1 | "sip_proxy_registrar1" | "ACME SIP Proxy and |
| | | Registrar" |
+-----------+------------------------+------------------------------+
The SIP-COMMON-MIB sipCommonCfgTable would have only one row to cover
both the proxy and the registrar.
The SIP-COMMON-MIB sipCommonCfgTable might be populated as:
+----------+---------------------------+-----------------------------+
|applIndex |sipCommonCfgProtocolVersion|sipCommonCfgServiceOperStatus|
+----------+---------------------------+-----------------------------+
| 1 | "SIP/2.0" | up(1) |
+----------+---------------------------+-----------------------------+
Lingle, et al. Standards Track [Page 9]RFC 4780 SIP MIB Modules April 2007
while the sipServerRegUserTable in SIP-SERVER-MIB might be populated
as:
+-----------+-----------------------+---------------------+-----+
| applIndex | sipServerRegUserIndex | sipServerRegUserUri | ... |
+-----------+-----------------------+---------------------+-----+
| 2 | 1 | bob@example.com | |
| 2 | 2 | alice@example.com | |
| 2 | 3 | kevin@example.com | |
| 2 | 4 | jf@example.com | |
+-----------+-----------------------+---------------------+-----+
The NETWORK-SERVICES-MIB assocTable is not considered a requirement
for SIP systems. It is not a mandatory group for compliance with the
NETWORK-SERVICES-MIB module.
The relationship between the value of applOperStatus and
sipCommonCfgServiceOperStatus is as follows:
+-------------------------------+---------------+-------------------+
| sipCommonCfgServiceOperStatus | -- | applOperStatus |
| | corresponds | |
| | to --> | |
+-------------------------------+---------------+-------------------+
| up | --> | up |
| down | --> | down |
| congested | --> | congested |
| restarting | --> | restarting |
| quiescing | --> | quiescing |
| testing | --> | up |
| unknown | --> | --indeterminate-- |
+-------------------------------+---------------+-------------------+
If the sipOperStatus is 'unknown', there is no corresponding value of
applOperStatus. Therefore, the last known value of applOperStatus
SHOULD be maintained until the sipOperStatus transitions to a value
that can be mapped appropriately.
5.3. IMPORTed MIB Modules and REFERENCE Clauses
The SIP MIB modules defined in this document IMPORT definitions
normatively from the following MIB modules, beyond [RFC2578],
[RFC2579], and [RFC2580]: INET-ADDRESS-MIB [RFC4001], NETWORK-
SERVICES-MIB [RFC2788], SNMP-FRAMEWORK-MIB [RFC3411].
This MIB module also includes REFERENCE clauses that normatively
refer to SIP [RFC3261] and INET-ADDRESS-MIB [RFC4001].
Lingle, et al. Standards Track [Page 10]RFC 4780 SIP MIB Modules April 2007
Finally, this MIB module makes informative references to several RFCs
in some of the examples described in the DESCRIPTION clauses,
including Reliability of Provisional Responses in SIP [RFC3262] and
SIP over SCTP [RFC4168].
6. Accommodating SIP Extension Methods
The core set of SIP methods is defined in RFC 3261 [RFC3261]. Other
IETF RFCs define additional methods. In the future, additional
methods may be defined. In order to avoid having to update the SIP-
COMMON-MIB module to accommodate these extension methods, we use a
method identifier name (SipTCMethodName TEXTUAL-CONVENTION) to
represent all SIP methods registered with IANA.
For example, the sipCommonMethodSupportedTable is the main table for
listing all of the SIP methods supported by a system, including the
SIP methods defined in RFC 3261 [RFC3261] and other SIP methods
registered with IANA. The table is informational in nature and
populated by the system. Entries cannot be added or deleted by an
SNMP manager.
The SIP specification (RFC 3261 [RFC3261], Section 27.4) establishes
the sub-registries for SIP Methods and Response Codes under
http://www.iana.org/assignments/sip-parameters. This document uses
the existing sub-registry for the names of registered SIP methods.
For example, in the sipCommonMethodSupportedTable of SIP-COMMON-MIB,
the sipCommonMethodSupportedName values can be represented as
follows:
+------------------------------+
| sipCommonMethodSupportedName |
+------------------------------+
| "ACK" |
| "BYE" |
| "CANCEL" |
| "INVITE" |
| "OPTIONS" |
+------------------------------+
Lingle, et al. Standards Track [Page 11]RFC 4780 SIP MIB Modules April 2007
7. Definitions
7.1. SIP Textual Conventions
SIP-TC-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
mib-2
FROM SNMPv2-SMI -- RFC 2578
TEXTUAL-CONVENTION
FROM SNMPv2-TC; -- RFC 2579
sipTC MODULE-IDENTITY
LAST-UPDATED "200704200000Z"
ORGANIZATION "IETF Session Initiation Protocol Working Group"
CONTACT-INFO
"SIP WG email: sip@ietf.org
Co-editor Kevin Lingle
Cisco Systems, Inc.
postal: 7025 Kit Creek Road
P.O. Box 14987
Research Triangle Park, NC 27709
USA
email: klingle@cisco.com
phone: +1 919 476 2029
Co-editor Joon Maeng
email: jmaeng@austin.rr.com
Co-editor Jean-Francois Mule
CableLabs
postal: 858 Coal Creek Circle
Louisville, CO 80027
USA
email: jf.mule@cablelabs.com
phone: +1 303 661 9100
Co-editor Dave Walker
email: drwalker@rogers.com"
DESCRIPTION
"Session Initiation Protocol (SIP) MIB TEXTUAL-CONVENTION
module used by other SIP-related MIB Modules.
Copyright (C) The IETF Trust (2007). This version of
this MIB module is part of RFC 4780; see the RFC itself for
Lingle, et al. Standards Track [Page 12]RFC 4780 SIP MIB Modules April 2007
full legal notices."
REVISION "200704200000Z"
DESCRIPTION
"Initial version of the IETF SIP-TC-MIB module. This version
published as part of RFC 4780."
::= { mib-2 148 }
--
-- Textual Conventions
--
SipTCTransportProtocol ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This convention is a bit map. Each bit represents a transport
protocol. If a bit has value 1, then that selected transport
protocol is in some way dependent on the context of the object
using this convention. If a bit has value 0, then that
transport protocol is not selected. Combinations of bits can
be set when multiple transport protocols are selected.
bit 0: a protocol other than those defined here
bit 1: User Datagram Protocol
bit 2: Transmission Control Protocol
bit 3: Stream Control Transmission Protocol
bit 4: Transport Layer Security Protocol over TCP
bit 5: Transport Layer Security Protocol over SCTP
"
REFERENCE "RFC 3261, Section 18 and RFC 4168"
SYNTAX BITS {
other(0), -- none of the following
udp(1),
tcp(2),
sctp(3), -- RFC4168
tlsTcp(4),
tlsSctp(5) -- RFC 4168
}
SipTCEntityRole ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This convention defines the role of a SIP entity. Examples of
SIP entities are proxies, user agents, redirect servers,
registrars, or combinations of the above.
User Agent (UA): A logical entity that can act as both a user
agent client and user agent server.
Lingle, et al. Standards Track [Page 13]RFC 4780 SIP MIB Modules April 2007
User Agent Client (UAC): A logical entity that creates a new
request, and then uses the client transaction state machinery
to send it. The role of UAC lasts only for the duration of
that transaction. In other words, if a piece of software
initiates a request, it acts as a UAC for the duration of that
transaction. If it receives a request later, it assumes the
role of a user agent server for the processing of that
transaction.
User Agent Server (UAS): A logical entity that generates a
response to a SIP request. The response accepts, rejects,
or redirects the request. This role lasts only for the
duration of that transaction. In other words, if a piece of
software responds to a request, it acts as a UAS for the
duration of that transaction. If it generates a request
later, it assumes the role of a user agent client for the
processing of that transaction.
Proxy, Proxy Server: An intermediary entity that acts as both
a server and a client for the purpose of making requests on
behalf of other clients. A proxy server primarily plays the
role of routing, which means its job is to ensure that a
request is sent to another entity 'closer' to the targeted
user. Proxies are also useful for enforcing policy. A proxy
interprets and, if necessary, rewrites specific parts of a
request message before forwarding it.
Redirect Server: A redirect server is a user agent server that
generates 3xx responses to requests it receives, directing the
client to contact an alternate set of URIs.
Registrar: A registrar is a server that accepts REGISTER
requests and places the information it receives in those
requests into the location service for the domain it handles."
REFERENCE
"RFC 3261, Section 6"
SYNTAX BITS {
other(0),
userAgent(1),
proxyServer(2),
redirectServer(3),
registrarServer(4)
}
SipTCOptionTagHeaders ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This convention defines the header fields that use the option
Lingle, et al. Standards Track [Page 14]RFC 4780 SIP MIB Modules April 2007
tags per Section 19.2 of RFC 3261. These tags are used in
Require (Section 20.32), Proxy-Require (Section 20.29),
Supported (Section 20.37), and Unsupported (Section 20.40)
header fields."
REFERENCE
"RFC 3261, Sections 19.2, 20.32, 20.29, 20.37, and 20.40"
SYNTAX BITS {
require(0), -- Require header
proxyRequire(1), -- Proxy-Require header
supported(2), -- Supported header
unsupported(3) -- Unsupported header
}
SipTCMethodName ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This TEXTUAL-CONVENTION is a string that uniquely identifies a
SIP method. The scope of uniqueness is the context of all
defined SIP methods.
Experimental support of extension methods is acceptable and
expected. Extension methods are those defined in
Internet-Draft documents but not yet allocated and
officially sanctioned by IANA.
To support experimental extension methods, any object using
this TEXTUAL-CONVENTION as syntax MAY return/accept a method
identifier value other than those sanctioned by IANA. That
system MUST ensure no collisions with officially assigned
method names."
REFERENCE
"RFC 3261, Section 27.4"
SYNTAX OCTET STRING (SIZE (1..100))
END
7.2. SIP Common MIB Module
SIP-COMMON-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
NOTIFICATION-TYPE,
Counter32,
Gauge32,
TimeTicks,
Unsigned32,
Lingle, et al. Standards Track [Page 15]RFC 4780 SIP MIB Modules April 2007
mib-2
FROM SNMPv2-SMI -- RFC 2578
RowStatus,
TimeStamp,
TruthValue
FROM SNMPv2-TC -- RFC 2579
MODULE-COMPLIANCE,
OBJECT-GROUP,
NOTIFICATION-GROUP
FROM SNMPv2-CONF -- RFC 2580
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB -- RFC 3411
SipTCTransportProtocol,
SipTCMethodName,
SipTCEntityRole,
SipTCOptionTagHeaders
FROM SIP-TC-MIB -- RFC 4780
applIndex
FROM NETWORK-SERVICES-MIB -- RFC 2788
InetPortNumber
FROM INET-ADDRESS-MIB; -- RFC 4001
sipCommonMIB MODULE-IDENTITY
LAST-UPDATED "200704200000Z"
ORGANIZATION "IETF Session Initiation Protocol Working Group"
CONTACT-INFO
"SIP WG email: sip@ietf.org
Co-editor Kevin Lingle
Cisco Systems, Inc.
postal: 7025 Kit Creek Road
P.O. Box 14987
Research Triangle Park, NC 27709
USA
email: klingle@cisco.com
phone: +1 919 476 2029
Co-editor Joon Maeng
email: jmaeng@austin.rr.com
Co-editor Jean-Francois Mule
CableLabs
Lingle, et al. Standards Track [Page 16]RFC 4780 SIP MIB Modules April 2007
postal: 858 Coal Creek Circle
Louisville, CO 80027
USA
email: jf.mule@cablelabs.com
phone: +1 303 661 9100
Co-editor Dave Walker
email: drwalker@rogers.com"
DESCRIPTION
"Session Initiation Protocol (SIP) Common MIB module. This
module defines objects that may be common to all SIP entities.
SIP is an application-layer signaling protocol for creating,
modifying and terminating multimedia sessions with one or more
participants. These sessions include Internet multimedia
conferences and Internet telephone calls. SIP is defined in
RFC 3261 (June 2002).
This MIB is defined for managing objects that are common to
SIP User Agents (UAs), Proxy, Redirect, and Registrar servers.
Objects specific to each of these entities MAY be managed using
entity specific MIBs defined in other modules.
Copyright (C) The IETF Trust (2007). This version of
this MIB module is part of RFC 4780; see the RFC itself for
full legal notices."
REVISION "200704200000Z"
DESCRIPTION
"Initial version of the IETF SIP-COMMON-MIB module. This
version published as part of RFC 4780."
::= { mib-2 149 }
-- Top-Level Components of this MIB.
sipCommonMIBNotifications OBJECT IDENTIFIER ::= { sipCommonMIB 0 }
sipCommonMIBObjects OBJECT IDENTIFIER ::= { sipCommonMIB 1 }
sipCommonMIBConformance OBJECT IDENTIFIER ::= { sipCommonMIB 2 }
--
-- This MIB contains objects that are common to all SIP entities.
--
-- Common basic configuration
sipCommonCfgBase OBJECT IDENTIFIER ::= { sipCommonMIBObjects 1 }
-- Protocol timer configuration
sipCommonCfgTimer OBJECT IDENTIFIER ::= { sipCommonMIBObjects 2 }
-- SIP message summary statistics
Lingle, et al. Standards Track [Page 17]RFC 4780 SIP MIB Modules April 2007
sipCommonSummaryStats OBJECT IDENTIFIER ::= { sipCommonMIBObjects 3 }
-- Per method statistics
sipCommonMethodStats OBJECT IDENTIFIER ::= { sipCommonMIBObjects 4 }
-- Per Status code or status code class statistics
sipCommonStatusCode OBJECT IDENTIFIER ::= { sipCommonMIBObjects 5 }
-- Transaction statistics
sipCommonStatsTrans OBJECT IDENTIFIER ::= { sipCommonMIBObjects 6 }
-- Method retry statistics
sipCommonStatsRetry OBJECT IDENTIFIER ::= { sipCommonMIBObjects 7 }
-- Other statistics
sipCommonOtherStats OBJECT IDENTIFIER ::= { sipCommonMIBObjects 8 }
-- Accessible-for-notify objects
sipCommonNotifObjects OBJECT IDENTIFIER ::= { sipCommonMIBObjects 9 }
--
-- Common Configuration Objects
--
sipCommonCfgTable OBJECT-TYPE
SYNTAX SEQUENCE OF SipCommonCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the common configuration objects applicable
to all SIP entities."
::= { sipCommonCfgBase 1 }
sipCommonCfgEntry OBJECT-TYPE
SYNTAX SipCommonCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row of common configuration.
Each row represents objects for a particular SIP entity
instance present in this system. applIndex is used to uniquely
identify these instances of SIP entities and correlate them
through the common framework of the NETWORK-SERVICES-MIB (RFC
2788)."
INDEX { applIndex }
::= { sipCommonCfgTable 1 }
SipCommonCfgEntry ::= SEQUENCE {
Lingle, et al. Standards Track [Page 18]RFC 4780 SIP MIB Modules April 2007
sipCommonCfgProtocolVersion SnmpAdminString,
sipCommonCfgServiceOperStatus INTEGER,
sipCommonCfgServiceStartTime TimeTicks,
sipCommonCfgServiceLastChange TimeTicks,
sipCommonCfgOrganization SnmpAdminString,
sipCommonCfgMaxTransactions Unsigned32,
sipCommonCfgServiceNotifEnable BITS,
sipCommonCfgEntityType SipTCEntityRole
}
sipCommonCfgProtocolVersion OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object will reflect the version of SIP supported by this
SIP entity. It will follow the same format as SIP version
information contained in the SIP messages generated by this SIP
entity. For example, entities supporting SIP version 2 will
return 'SIP/2.0' as dictated by the standard."
REFERENCE
"RFC 3261, Section 7.1"
::= { sipCommonCfgEntry 1 }
sipCommonCfgServiceOperStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
up(2),
down(3),
congested(4),
restarting(5),
quiescing(6),
testing(7)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the current operational state of
the SIP application.
unknown : The operational status cannot be determined
for some reason.
up : The application is operating normally and is
processing (receiving and possibly issuing) SIP
requests and responses.
down : The application is currently unable to process
SIP messages.
congested : The application is operational but no additional
Lingle, et al. Standards Track [Page 19]RFC 4780 SIP MIB Modules April 2007
inbound transactions can be accommodated at the
moment.
restarting : The application is currently unavailable, but it
is in the process of restarting and will
presumably, soon be able to process SIP messages.
quiescing : The application is currently operational
but has been administratively put into
quiescence mode. Additional inbound
transactions MAY be rejected.
testing : The application is currently in test mode
and MAY not be able to process SIP messages.
The operational status values defined for this object are not
based on any specific information contained in the SIP
standard."
::= { sipCommonCfgEntry 2 }
sipCommonCfgServiceStartTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time the SIP entity was last
started. If started prior to the last re-initialization of the
local network management subsystem, then this object contains a
zero value."
::= { sipCommonCfgEntry 3 }
sipCommonCfgServiceLastChange OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time the SIP entity entered its
current operational state. If the current state was entered
prior to the last re-initialization of the local network
management subsystem, then this object contains a zero value."
::= { sipCommonCfgEntry 4 }
sipCommonCfgOrganization OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the organization name that the SIP entity
inserts into Organization headers of SIP messages processed by
this system. If the string is empty, no Organization header is
to be generated."
Lingle, et al. Standards Track [Page 20]RFC 4780 SIP MIB Modules April 2007
REFERENCE
"RFC 3261, Section 20.25"
::= { sipCommonCfgEntry 5 }
sipCommonCfgMaxTransactions OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the maximum number of simultaneous
transactions per second that the SIP entity can manage. In
general, the value of this object SHOULD reflect a level of
transaction processing per second that is considered high
enough to impact the system's CPU and/or memory resources to
the point of deteriorating SIP call processing but not high
enough to cause catastrophic system failure."
::= { sipCommonCfgEntry 6 }
sipCommonCfgServiceNotifEnable OBJECT-TYPE
SYNTAX BITS {
sipCommonServiceColdStart(0),
sipCommonServiceWarmStart(1),
sipCommonServiceStatusChanged(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies which SIP service related notifications
are enabled. Each bit represents a specific notification. If
a bit has a value 1, the associated notification is enabled and
will be generated by the SIP entity at the appropriate time.
Support for these notifications is OPTIONAL: either none or all
notification values are supported. If an implementation does
not support this object, it should return a 'noSuchObject'
exception to an SNMP GET operation. If notifications are
supported, this object's default value SHOULD reflect
sipCommonServiceColdStart and sipCommonServiceWarmStart enabled
and sipCommonServiceStatusChanged disabled.
This object value SHOULD persist across reboots."
DEFVAL { { sipCommonServiceColdStart,
sipCommonServiceWarmStart } }
::= { sipCommonCfgEntry 7 }
sipCommonCfgEntityType OBJECT-TYPE
SYNTAX SipTCEntityRole
MAX-ACCESS read-only
Lingle, et al. Standards Track [Page 21]RFC 4780 SIP MIB Modules April 2007
STATUS current
DESCRIPTION
"This object identifies the list of SIP entities to which this
row is related. It is defined as a bit map. Each bit
represents a type of SIP entity. If a bit has value 1, the
SIP entity represented by this row plays the role of this
entity type. If a bit has value 0, the SIP entity represented
by this row does not act as this entity type. Combinations
of bits can be set when the SIP entity plays multiple SIP
roles."
::= { sipCommonCfgEntry 8 }
--
-- Support for multiple ports
--
sipCommonPortTable OBJECT-TYPE
SYNTAX SEQUENCE OF SipCommonPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the list of ports that each SIP entity in
this system is allowed to use. These ports can be advertised
using the Contact header in a REGISTER request or response."
::= { sipCommonCfgBase 2 }
sipCommonPortEntry OBJECT-TYPE
SYNTAX SipCommonPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Specification of a particular port.
Each row represents those objects for a particular SIP entity
present in this system. applIndex is used to uniquely identify
these instances of SIP entities and correlate them through
the common framework of the NETWORK-SERVICES-MIB (RFC 2788)."
INDEX { applIndex, sipCommonPort }
::= { sipCommonPortTable 1 }
SipCommonPortEntry ::= SEQUENCE {
sipCommonPort InetPortNumber,
sipCommonPortTransportRcv SipTCTransportProtocol
}
sipCommonPort OBJECT-TYPE
SYNTAX InetPortNumber (1..65535)
MAX-ACCESS not-accessible
STATUS current
Lingle, et al. Standards Track [Page 22]RFC 4780 SIP MIB Modules April 2007
DESCRIPTION
"This object reflects a particular port that can be used by the
SIP application."
::= { sipCommonPortEntry 1 }
sipCommonPortTransportRcv OBJECT-TYPE
SYNTAX SipTCTransportProtocol
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object will specify the transport protocol the SIP entity
will use to receive SIP messages.
This object is a bit map. Each bit represents a transport
protocol. If a bit has value 1, then that transport protocol
is currently being used. If a bit has value 0, then that
transport protocol is currently not being used."
::= { sipCommonPortEntry 2 }
--
-- Support for SIP option tags (SIP extensions).
-- SIP extensions MAY be supported or required by SIP entities.
--
sipCommonOptionTagTable OBJECT-TYPE
SYNTAX SEQUENCE OF SipCommonOptionTagEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains a list of the SIP option tags (SIP
extensions) that are either required, supported, or
unsupported by the SIP entity. These option tags are
used in the Require, Proxy-Require, Supported, and
Unsupported header fields.
Example: If a user agent client supports, and requires the
server to support, reliability of provisional responses
(RFC 3262), this table contains a row with the option tag string
'100rel' in sipCommonOptionTag and the OCTET STRING value of
'1010 0000' or '0xA0' in sipCommonOptionTagHeaderField.
If a server does not support the required feature (indicated in
a Require header to a UAS, or in a Proxy-Require to a Proxy
Server), the server returns a 420 Bad Extension listing the
feature in an Unsupported header.
Normally, the list of such features supported by an entity is
static (i.e., will not change over time)."
Lingle, et al. Standards Track [Page 23]RFC 4780 SIP MIB Modules April 2007
REFERENCE
"RFC 3261, Sections 19.2, 20.32, 20.29, 20.37, and 20.40"
::= { sipCommonCfgBase 3 }
sipCommonOptionTagEntry OBJECT-TYPE
SYNTAX SipCommonOptionTagEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A particular SIP option tag (extension) supported or
unsupported by the SIP entity, and which may be supported or
required by a peer.
Each row represents those objects for a particular SIP entity
present in this system. applIndex is used to uniquely identify
these instances of SIP entities and correlate them through the
common framework of the NETWORK-SERVICES-MIB (RFC 2788)."
INDEX { applIndex, sipCommonOptionTagIndex }
::= { sipCommonOptionTagTable 1 }
SipCommonOptionTagEntry ::= SEQUENCE {
sipCommonOptionTagIndex Unsigned32,
sipCommonOptionTag SnmpAdminString,
sipCommonOptionTagHeaderField SipTCOptionTagHeaders
}
sipCommonOptionTagIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object uniquely identifies a conceptual row in the table."
::= { sipCommonOptionTagEntry 1 }
sipCommonOptionTag OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the SIP option tag. The option tag names
are registered with IANA and available at http://www.iana.org."
REFERENCE "RFC 3261, Section 27.1"
::= { sipCommonOptionTagEntry 2 }
sipCommonOptionTagHeaderField OBJECT-TYPE
SYNTAX SipTCOptionTagHeaders
MAX-ACCESS read-only
STATUS current
Lingle, et al. Standards Track [Page 24]RFC 4780 SIP MIB Modules April 2007
DESCRIPTION
"This object indicates whether the SIP option tag is supported
(Supported header), unsupported (Unsupported header), or
required (Require or Proxy-Require header) by the SIP entity.
A SIP option tag may be both supported and required."
::= { sipCommonOptionTagEntry 3 }
--
-- Supported SIP Methods
--
sipCommonMethodSupportedTable OBJECT-TYPE
SYNTAX SEQUENCE OF SipCommonMethodSupportedEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains a list of methods supported by each SIP
entity in this system (see the standard set of SIP methods in
Section 7.1 of RFC 3261). Any additional methods that may be
incorporated into the SIP protocol can be represented by this
table without any requirement to update this MIB module.
The table is informational in nature and conveys capabilities
of the managed system to the SNMP Manager.
From a protocol point of view, the list of methods advertised
by the SIP entity in the Allow header (Section 20.5 of RFC
3261) MUST be consistent with the methods reflected in this
table."
::= { sipCommonCfgBase 4 }
sipCommonMethodSupportedEntry OBJECT-TYPE
SYNTAX SipCommonMethodSupportedEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A particular method supported by the SIP entity.
Each row represents those objects for a particular SIP entity
present in this system. applIndex is used to uniquely identify
these instances of SIP entities and correlate them through
the common framework of the NETWORK-SERVICES-MIB (RFC 2788)."
INDEX { applIndex, sipCommonMethodSupportedIndex }
::= { sipCommonMethodSupportedTable 1 }
SipCommonMethodSupportedEntry ::= SEQUENCE {
sipCommonMethodSupportedIndex Unsigned32,
sipCommonMethodSupportedName SipTCMethodName
}
Lingle, et al. Standards Track [Page 25]RFC 4780 SIP MIB Modules April 2007
sipCommonMethodSupportedIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object uniquely identifies a conceptual row in the table
and reflects an assigned number used to identify a specific
SIP method.
This identifier is suitable for referencing the associated
method throughout this and other MIBs supported by this managed
system."
::= { sipCommonMethodSupportedEntry 1 }
sipCommonMethodSupportedName OBJECT-TYPE
SYNTAX SipTCMethodName
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the supported method's name. The method
name MUST be all upper case (e.g., 'INVITE')."
::= { sipCommonMethodSupportedEntry 2 }
--
-- SIP Timer Configuration
--
sipCommonCfgTimerTable OBJECT-TYPE
SYNTAX SEQUENCE OF SipCommonCfgTimerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains timer configuration objects applicable to
SIP user agent and SIP stateful Proxy Server entities."
::= { sipCommonCfgTimer 1 }
sipCommonCfgTimerEntry OBJECT-TYPE
SYNTAX SipCommonCfgTimerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row of timer configuration.
Each row represents those objects for a particular SIP entity
present in this system. applIndex is used to uniquely identify
these instances of SIP entities and correlate them through
the common framework of the NETWORK-SERVICES-MIB (RFC 2788).
The objects in this table entry SHOULD be non-volatile and
their value SHOULD be kept at reboot."
Lingle, et al. Standards Track [Page 26]RFC 4780 SIP MIB Modules April 2007
INDEX { applIndex }
::= { sipCommonCfgTimerTable 1 }
SipCommonCfgTimerEntry ::= SEQUENCE {
sipCommonCfgTimerA Unsigned32,
sipCommonCfgTimerB Unsigned32,
sipCommonCfgTimerC Unsigned32,
sipCommonCfgTimerD Unsigned32,
sipCommonCfgTimerE Unsigned32,
sipCommonCfgTimerF Unsigned32,
sipCommonCfgTimerG Unsigned32,
sipCommonCfgTimerH Unsigned32,
sipCommonCfgTimerI Unsigned32,
sipCommonCfgTimerJ Unsigned32,
sipCommonCfgTimerK Unsigned32,
sipCommonCfgTimerT1 Unsigned32,
sipCommonCfgTimerT2 Unsigned32,
sipCommonCfgTimerT4 Unsigned32
}
sipCommonCfgTimerA OBJECT-TYPE
SYNTAX Unsigned32 (100..1000)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the initial value for the retransmit timer
for the INVITE method. The retransmit timer doubles after each
retransmission, ensuring an exponential backoff in network
traffic. This object represents the initial time a SIP entity
will wait to receive a provisional response to an INVITE before
resending the INVITE request."
REFERENCE
"RFC 3261, Section 17.1.1.2"
DEFVAL { 500 }
::= { sipCommonCfgTimerEntry 1 }
sipCommonCfgTimerB OBJECT-TYPE
SYNTAX Unsigned32 (32000..300000)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the maximum time a SIP entity will wait to
receive a final response to an INVITE. The timer is started
upon transmission of the initial INVITE request."
REFERENCE
"RFC 3261, Section 17.1.1.2"
Lingle, et al. Standards Track [Page 27]RFC 4780 SIP MIB Modules April 2007
DEFVAL { 32000 }
::= { sipCommonCfgTimerEntry 2 }
sipCommonCfgTimerC OBJECT-TYPE
SYNTAX Unsigned32 (180000..300000)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the maximum time a SIP Proxy Server will
wait to receive a provisional response to an INVITE. The Timer
C MUST be set for each client transaction when an INVITE
request is proxied."
REFERENCE
"RFC 3261, Section 16.6"
DEFVAL { 180000 }
::= { sipCommonCfgTimerEntry 3 }
sipCommonCfgTimerD OBJECT-TYPE
SYNTAX Unsigned32 (0..300000)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the amount of time that the server
transaction can remain in the 'Completed' state when unreliable
transports are used. The default value MUST be equal to or
greater than 32000 for UDP transport, and its value MUST be 0
for TCP/SCTP transport."
REFERENCE
"RFC 3261, Section 17.1.1.2"
DEFVAL { 32000 }
::= { sipCommonCfgTimerEntry 4 }
sipCommonCfgTimerE OBJECT-TYPE
SYNTAX Unsigned32 (100..1000)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the initial value for the retransmit timer
for a non-INVITE method while in 'Trying' state. The
retransmit timer doubles after each retransmission until it
reaches T2 to ensure an exponential backoff in network traffic.
This object represents the initial time a SIP entity will wait
to receive a provisional response to the request before
resending the non-INVITE request."
REFERENCE
Lingle, et al. Standards Track [Page 28]RFC 4780 SIP MIB Modules April 2007
"RFC 3261, Section 17.1.2.2"
DEFVAL { 500 }
::= { sipCommonCfgTimerEntry 5 }
sipCommonCfgTimerF OBJECT-TYPE
SYNTAX Unsigned32 (32000..300000)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the maximum time a SIP entity will wait to
receive a final response to a non-INVITE request. The timer is
started upon transmission of the initial request."
REFERENCE
"RFC 3261, Section 17.1.2.2"
DEFVAL { 32000 }
::= { sipCommonCfgTimerEntry 6 }
sipCommonCfgTimerG OBJECT-TYPE
SYNTAX Unsigned32 (0..1000)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the initial value for the retransmit timer
for final responses to INVITE requests. If timer G fires, the
response is passed to the transport layer again for
retransmission, and timer G is set to fire in MIN(2*T1, T2)
seconds. From then on, when timer G fires, the response is
passed to the transport again for transmission, and timer G is
reset with a value that doubles, unless that value exceeds T2,
in which case, it is reset with the value of T2. The default
value MUST be T1 for UDP transport, and its value MUST be 0 for
reliable transport like TCP/SCTP."
REFERENCE
"RFC 3261, Section 17.2.1"
DEFVAL { 500 }
::= { sipCommonCfgTimerEntry 7 }
sipCommonCfgTimerH OBJECT-TYPE
SYNTAX Unsigned32 (32000..300000)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the maximum time a server will wait to
receive an ACK before it abandons retransmitting the response.
Lingle, et al. Standards Track [Page 29]RFC 4780 SIP MIB Modules April 2007
The timer is started upon entering the 'Completed' state."
REFERENCE
"RFC 3261, Section 17.2.1"
DEFVAL { 32000 }
::= { sipCommonCfgTimerEntry 8 }
sipCommonCfgTimerI OBJECT-TYPE
SYNTAX Unsigned32 (0..10000)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the maximum time a SIP entity will wait to
receive additional ACK message retransmissions.
The timer is started upon entering the 'Confirmed' state. The
default value MUST be T4 for UDP transport and its value MUST
be 0 for reliable transport like TCP/SCTP."
REFERENCE
"RFC 3261, Section 17.2.1"
DEFVAL { 5000 }
::= { sipCommonCfgTimerEntry 9 }
sipCommonCfgTimerJ OBJECT-TYPE
SYNTAX Unsigned32 (32000..300000)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the maximum time a SIP server will wait to
receive retransmissions of non-INVITE requests. The timer is
started upon entering the 'Completed' state for non-INVITE
transactions. When timer J fires, the server MUST transition to
the 'Terminated' state."
REFERENCE
"RFC 3261, Section 17.2.2"
DEFVAL { 32000 }
::= { sipCommonCfgTimerEntry 10 }
sipCommonCfgTimerK OBJECT-TYPE
SYNTAX Unsigned32 (0..10000)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the maximum time a SIP client will wait to
receive retransmissions of responses to non-INVITE requests.
The timer is started upon entering the 'Completed' state for
Lingle, et al. Standards Track [Page 30]RFC 4780 SIP MIB Modules April 2007
non-INVITE transactions. When timer K fires, the server MUST
transition to the 'Terminated' state. The default value MUST
be T4 for UDP transport, and its value MUST be 0 for reliable
transport like TCP/SCTP."
REFERENCE
"RFC 3261, Section 17.1.2.2"
DEFVAL { 5000 }
::= { sipCommonCfgTimerEntry 11 }
sipCommonCfgTimerT1 OBJECT-TYPE
SYNTAX Unsigned32 (200..10000)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the T1 timer for a SIP entity. T1 is an
estimate of the round-trip time (RTT) between the client and
server transactions."
REFERENCE
"RFC 3261, Section 17"
DEFVAL { 500 }
::= { sipCommonCfgTimerEntry 12 }
sipCommonCfgTimerT2 OBJECT-TYPE
SYNTAX Unsigned32 (200..10000)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the T2 timer for a SIP entity. T2 is the
maximum retransmit interval for non-INVITE requests and INVITE
responses. It's used in various parts of the protocol to reset
other Timer* objects to this value."
REFERENCE
"RFC 3261, Section 17"
DEFVAL { 4000 }
::= { sipCommonCfgTimerEntry 13 }
sipCommonCfgTimerT4 OBJECT-TYPE
SYNTAX Unsigned32 (200..10000)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the T4 timer for a SIP entity. T4 is the
maximum duration a message will remain in the network. It
represents the amount of time the network will take to clear
messages between client and server transactions. It's used in
Lingle, et al. Standards Track [Page 31]RFC 4780 SIP MIB Modules April 2007
various parts of the protocol to reset other Timer* objects to
this value."
REFERENCE
"RFC 3261, Section 17"
DEFVAL { 5000 }
::= { sipCommonCfgTimerEntry 14 }
--
-- Common Statistics Objects
--
--
-- Summary Statistics
--
sipCommonSummaryStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF SipCommonSummaryStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the summary statistics objects applicable
to all SIP entities. Each row represents those objects for a
particular SIP entity present in this system."
::= { sipCommonSummaryStats 1 }
sipCommonSummaryStatsEntry OBJECT-TYPE
SYNTAX SipCommonSummaryStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row of summary statistics.
Each row represents those objects for a particular SIP entity
present in this system. applIndex is used to uniquely identify
these instances of SIP entities and correlate them through
the common framework of the NETWORK-SERVICES-MIB (RFC 2788)."
INDEX { applIndex }
::= { sipCommonSummaryStatsTable 1 }
SipCommonSummaryStatsEntry ::= SEQUENCE {
sipCommonSummaryInRequests Counter32,
sipCommonSummaryOutRequests Counter32,
sipCommonSummaryInResponses Counter32,
sipCommonSummaryOutResponses Counter32,
sipCommonSummaryTotalTransactions Counter32,
sipCommonSummaryDisconTime TimeStamp
}
sipCommonSummaryInRequests OBJECT-TYPE
Lingle, et al. Standards Track [Page 32]RFC 4780 SIP MIB Modules April 2007
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the total number of SIP request messages
received by the SIP entity, including retransmissions.
Discontinuities in the value of this counter can occur at
re-initialization of the SIP entity or service. A Management
Station can detect discontinuities in this counter by
monitoring the sipCommonSummaryDisconTime object in the same
row."
::= { sipCommonSummaryStatsEntry 1 }
sipCommonSummaryOutRequests OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the total number of SIP request messages
sent out (originated and relayed) by the SIP entity. Where a
particular message is sent more than once, for example as a
retransmission or as a result of forking, each transmission is
counted separately.
Discontinuities in the value of this counter can occur at
re-initialization of the SIP entity or service. A Management
Station can detect discontinuities in this counter by
monitoring the sipCommonSummaryDisconTime object in the same
row."
::= { sipCommonSummaryStatsEntry 2 }
sipCommonSummaryInResponses OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the total number of SIP response messages
received by the SIP entity, including retransmissions.
Discontinuities in the value of this counter can occur at
re-initialization of the SIP entity or service. A Management
Station can detect discontinuities in this counter by
monitoring the sipCommonSummaryDisconTime object in the same
row."
::= { sipCommonSummaryStatsEntry 3 }
sipCommonSummaryOutResponses OBJECT-TYPE
Lingle, et al. Standards Track [Page 33]RFC 4780 SIP MIB Modules April 2007
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the total number of SIP response messages
sent (originated and relayed) by the SIP entity including
retransmissions.
Discontinuities in the value of this counter can occur at
re-initialization of the SIP entity or service. A Management
Station can detect discontinuities in this counter by
monitoring the sipCommonSummaryDisconTime object in the same
row."
::= { sipCommonSummaryStatsEntry 4 }
sipCommonSummaryTotalTransactions OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains a count of the number of transactions that
are in progress and transactions that have reached the
'Terminated' state. It is not applicable to stateless SIP Proxy
Servers.
A SIP transaction occurs between a client and a server, and
comprises all messages from the first request sent from the
client to the server, up to a final (non-1xx) response sent
from the server to the client.
If the request is INVITE and the final response is a non-2xx,
the transaction also include an ACK to the response. The ACK
for a 2xx response to an INVITE request is a separate
transaction.
The branch ID parameter in the Via header field values serves
as a transaction identifier.
A transaction is identified by the CSeq sequence number within
a single call leg. The ACK request has the same CSeq number as
the corresponding INVITE request, but comprises a transaction
of its own.
In the case of a forked request, each branch counts as a single
transaction.
For a transaction stateless Proxy Server, this counter is
always 0.
Lingle, et al. Standards Track [Page 34]RFC 4780 SIP MIB Modules April 2007
Discontinuities in the value of this counter can occur at
re-initialization of the SIP entity or service. A Management
Station can detect discontinuities in this counter by
monitoring the sipCommonSummaryDisconTime object in the same
row."
::= { sipCommonSummaryStatsEntry 5 }
sipCommonSummaryDisconTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the sysUpTime object when the counters for the
summary statistics objects in this row last experienced a
discontinuity."
::= { sipCommonSummaryStatsEntry 6 }
--
-- SIP Method Statistics
-- Total counts for each SIP method.
--
sipCommonMethodStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF SipCommonMethodStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the method statistics objects for SIP
entities. Each row represents those objects for a particular
SIP entity present in this system."
::= { sipCommonMethodStats 1 }
sipCommonMethodStatsEntry OBJECT-TYPE
SYNTAX SipCommonMethodStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row of per entity method statistics.
Each row represents those objects for a particular SIP entity
present in this system. applIndex is used to uniquely identify
these instances of SIP entities and correlate them through
the common framework of the NETWORK-SERVICES-MIB (RFC 2788)."
INDEX { applIndex, sipCommonMethodStatsName }
::= { sipCommonMethodStatsTable 1 }
SipCommonMethodStatsEntry ::= SEQUENCE {
sipCommonMethodStatsName SipTCMethodName,
sipCommonMethodStatsOutbounds Counter32,
Lingle, et al. Standards Track [Page 35]RFC 4780 SIP MIB Modules April 2007
sipCommonMethodStatsInbounds Counter32,
sipCommonMethodStatsDisconTime TimeStamp
}
sipCommonMethodStatsName OBJECT-TYPE
SYNTAX SipTCMethodName
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object uniquely identifies the SIP method related to the
objects in a particular row."
::= { sipCommonMethodStatsEntry 1 }
sipCommonMethodStatsOutbounds OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the total number of requests sent by the
SIP entity, excluding retransmissions. Retransmissions are
counted separately and are not reflected in this counter. A
Management Station can detect discontinuities in this counter
by monitoring the sipCommonMethodStatsDisconTime object in the
same row."
REFERENCE
"RFC 3261, Section 7.1"
::= { sipCommonMethodStatsEntry 2 }
sipCommonMethodStatsInbounds OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the total number of requests received by
the SIP entity. Retransmissions are counted separately and are
not reflected in this counter. A Management Station can detect
discontinuities in this counter by monitoring the
sipCommonMethodStatsDisconTime object in the same row."
REFERENCE
"RFC 3261, Section 7.1"
::= { sipCommonMethodStatsEntry 3 }
sipCommonMethodStatsDisconTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Lingle, et al. Standards Track [Page 36]RFC 4780 SIP MIB Modules April 2007
"The value of the sysUpTime object when the counters for the
method statistics objects in this row last experienced a
discontinuity."
::= { sipCommonMethodStatsEntry 4 }
--
-- Support for specific status codes
--
sipCommonStatusCodeTable OBJECT-TYPE
SYNTAX SEQUENCE OF SipCommonStatusCodeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the list of SIP status codes that each SIP
entity in this system has been requested to monitor. It is the
mechanism by which specific status codes are monitored.
Entries created in this table must not persist across reboots."
::= { sipCommonStatusCode 1 }
sipCommonStatusCodeEntry OBJECT-TYPE
SYNTAX SipCommonStatusCodeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This row contains information on a particular SIP status code
that the SIP entity has been requested to monitor. Entries
created in this table must not persist across reboots.
Each row represents those objects for a particular SIP entity
present in this system. applIndex is used to uniquely identify
these instances of SIP entities and correlate them through
the common framework of the NETWORK-SERVICES-MIB (RFC 2788)."
INDEX { applIndex, sipCommonStatusCodeMethod,
sipCommonStatusCodeValue }
::= { sipCommonStatusCodeTable 1 }
SipCommonStatusCodeEntry ::= SEQUENCE {
sipCommonStatusCodeMethod SipTCMethodName,
sipCommonStatusCodeValue Unsigned32,
sipCommonStatusCodeIns Counter32,
sipCommonStatusCodeOuts Counter32,
sipCommonStatusCodeRowStatus RowStatus,
sipCommonStatusCodeDisconTime TimeStamp
}
sipCommonStatusCodeMethod OBJECT-TYPE
SYNTAX SipTCMethodName
MAX-ACCESS not-accessible
Lingle, et al. Standards Track [Page 37]RFC 4780 SIP MIB Modules April 2007
STATUS current
DESCRIPTION
"This object uniquely identifies a conceptual row in the
table."
::= { sipCommonStatusCodeEntry 1 }
sipCommonStatusCodeValue OBJECT-TYPE
SYNTAX Unsigned32 (100..999)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object contains a SIP status code value that the SIP
entity has been requested to monitor. All of the other
information in the row is related to this value."
::= { sipCommonStatusCodeEntry 2 }
sipCommonStatusCodeIns OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the total number of response messages
received by the SIP entity with the status code value contained
in the sipCommonStatusCodeValue column.
Discontinuities in the value of this counter can occur at
re-initialization of the SIP entity or service, or when the
monitoring of the status code is temporarily disabled. A
Management Station can detect discontinuities in this counter
by monitoring the sipCommonStatusCodeDisconTime object in the
same row."
::= { sipCommonStatusCodeEntry 3 }
sipCommonStatusCodeOuts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the total number of response messages sent
by the SIP entity with the status code value contained in the
sipCommonStatusCodeValue column.
Discontinuities in the value of this counter can occur at
re-initialization of the SIP entity or service, or when the
monitoring of the Status code is temporarily disabled. A
Management Station can detect discontinuities in this counter
by monitoring the sipCommonStatusCodeDisconTime object in the
same row."
Lingle, et al. Standards Track [Page 38]RFC 4780 SIP MIB Modules April 2007
::= { sipCommonStatusCodeEntry 4 }
sipCommonStatusCodeRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The row augmentation in sipCommonStatusCodeNotifTable will be
governed by the value of this RowStatus.
The values 'createAndGo' and 'destroy' are the only valid
values allowed for this object. If a row exists, it will
reflect a status of 'active' when queried."
::= { sipCommonStatusCodeEntry 5 }
sipCommonStatusCodeDisconTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the sysUpTime object when the counters for the
status code statistics objects in this row last experienced
a discontinuity."
::= { sipCommonStatusCodeEntry 6 }
--
-- Support for specific status code notifications
--
sipCommonStatusCodeNotifTable OBJECT-TYPE
SYNTAX SEQUENCE OF SipCommonStatusCodeNotifEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains objects to control notifications related to
particular status codes that each SIP entity in this system has
been requested to monitor.
There is an entry in this table corresponding to each entry in
sipCommonStatusCodeTable. Therefore, this table augments
sipCommonStatusCodeTable and utilizes the same index
methodology.
The objects in this table are not included directly in the
sipCommonStatusCodeTable simply to keep the status code
notification control objects separate from the actual status
code statistics."
::= { sipCommonStatusCode 2 }
Lingle, et al. Standards Track [Page 39]RFC 4780 SIP MIB Modules April 2007
sipCommonStatusCodeNotifEntry OBJECT-TYPE
SYNTAX SipCommonStatusCodeNotifEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This row contains information controlling notifications for a
particular SIP status code that the SIP entity has been
requested to monitor."
AUGMENTS { sipCommonStatusCodeEntry }
::= { sipCommonStatusCodeNotifTable 1 }
SipCommonStatusCodeNotifEntry ::= SEQUENCE {
sipCommonStatusCodeNotifSend TruthValue,
sipCommonStatusCodeNotifEmitMode INTEGER,
sipCommonStatusCodeNotifThresh Unsigned32,
sipCommonStatusCodeNotifInterval Unsigned32
}
sipCommonStatusCodeNotifSend OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object controls whether a sipCommonStatusCodeNotif is
emitted when the status code value specified by
sipCommonStatusCodeValue is sent or received. If the value of
this object is 'true', then a notification is sent. If it is
'false', no notification is sent.
Note well that a notification MAY be emitted for every message
sent or received that contains the particular status code.
Depending on the status code involved, this can cause a
significant number of notification emissions that could be
detrimental to network performance. Managers are forewarned to
be prudent in the use of this object to enable notifications.
Look to sipCommonStatusCodeNotifEmitMode for alternative
controls for sipCommonStatusCodeNotif emissions."
DEFVAL { false }
::= { sipCommonStatusCodeNotifEntry 1 }
sipCommonStatusCodeNotifEmitMode OBJECT-TYPE
SYNTAX INTEGER {
normal(1),
oneShot(2),
triggered(3) -- read-only
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
Lingle, et al. Standards Track [Page 40]RFC 4780 SIP MIB Modules April 2007
"The object sipCommonStatusCodeNotifSend MUST be set to 'true'
for the values of this object to have any effect. It is
RECOMMENDED that the desired emit mode be established by this
object prior to setting sipCommonStatusCodeNotifSend to 'true'.
This object and the sipCommonStatusCodeNotifSend object can
obviously be set independently, but their respective values
will have a dependency on each other and the resulting
notifications.
This object specifies the mode for emissions of
sipCommonStatusCodeNotif notifications.
normal : sipCommonStatusCodeNotif notifications will be
emitted by the system for each SIP response
message sent or received that contains the
desired status code.
oneShot : Only one sipCommonStatusCodeNotif notification
will be emitted. It will be the next SIP response
message sent or received that contains the
desired status code.
No more notifications are emitted until this
object is set to 'oneShot' again or set to
'normal'. This option is provided as a means of
quelling the potential promiscuous behavior that
can be associated with the
sipCommonStatusCodeNotif.
triggered : This value is only readable and cannot be set. It
reflects that the 'oneShot' case has occurred,
and indicates that the mode needs to be reset to
get further notifications. The mode is reset by
setting this object to 'oneShot' or 'normal'."
DEFVAL { oneShot }
::= { sipCommonStatusCodeNotifEntry 2 }
sipCommonStatusCodeNotifThresh OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the number of response messages sent or
received by this system that are considered excessive. Based
on crossing that threshold, a
sipCommonStatusCodeThreshExceededInNotif notification or a
sipCommonStatusCodeThreshExceededOutNotif will be sent. The
sipCommonStatusCodeThreshExceededInNotif and
Lingle, et al. Standards Track [Page 41]RFC 4780 SIP MIB Modules April 2007
sipCommonStatusCodeThreshExceededOutNotif notifications can be
used as an early warning mechanism in lieu of using
sipCommonStatusCodeNotif.
Note that the configuration applied by this object will be
applied equally to inbound and outbound response messages."
DEFVAL { 500 }
::= { sipCommonStatusCodeNotifEntry 3 }
sipCommonStatusCodeNotifInterval OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the time interval over which, if
sipCommonStatusCodeThresh is exceeded with respect to sent or
received messages, a sipCommonStatusCodeThreshExceededInNotif
or sipCommonStatusCodeThreshExceededOutNotif notification will
be sent.
Note that the configuration applied by this object will be
applied equally to inbound and outbound response messages."
DEFVAL { 60 }
::= { sipCommonStatusCodeNotifEntry 4 }
--
-- Transaction Statistics
--
sipCommonTransCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF SipCommonTransCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information on the transactions currently
awaiting definitive responses by each SIP entity in this
system.
This table does not apply to transaction stateless Proxy
Servers."
::= { sipCommonStatsTrans 1 }
sipCommonTransCurrentEntry OBJECT-TYPE
SYNTAX SipCommonTransCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information on a particular SIP entity's current transactions.
Lingle, et al. Standards Track [Page 42]RFC 4780 SIP MIB Modules April 2007
Each row represents those objects for a particular SIP entity
present in this system. applIndex is used to uniquely identify
these instances of SIP entities and correlate them through
the common framework of the NETWORK-SERVICES-MIB (RFC 2788)."
INDEX { applIndex }
::= { sipCommonTransCurrentTable 1 }
SipCommonTransCurrentEntry ::= SEQUENCE {
sipCommonTransCurrentactions Gauge32
}
sipCommonTransCurrentactions OBJECT-TYPE
SYNTAX Gauge32 (0..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the number of transactions awaiting
definitive (non-1xx) response. In the case of a forked
request, each branch counts as a single transaction
corresponding to the entity identified by applIndex."
::= { sipCommonTransCurrentEntry 1 }
--
-- SIP Retry Statistics
--
-- This group contains various statistics objects about
-- retransmission counts.
--
sipCommonStatsRetryTable OBJECT-TYPE
SYNTAX SEQUENCE OF SipCommonStatsRetryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains retry statistics objects applicable to each
SIP entity in this system."
::= { sipCommonStatsRetry 1 }
sipCommonStatsRetryEntry OBJECT-TYPE
SYNTAX SipCommonStatsRetryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row of retry statistics.
Each row represents those objects for a particular SIP entity
present in this system. applIndex is used to uniquely identify
these instances of SIP entities and correlate them through the
common framework of the NETWORK-SERVICES-MIB (RFC 2788)."
Lingle, et al. Standards Track [Page 43]RFC 4780 SIP MIB Modules April 2007
INDEX { applIndex, sipCommonStatsRetryMethod }
::= { sipCommonStatsRetryTable 1 }
SipCommonStatsRetryEntry ::= SEQUENCE {
sipCommonStatsRetryMethod SipTCMethodName,
sipCommonStatsRetries Counter32,
sipCommonStatsRetryFinalResponses Counter32,
sipCommonStatsRetryNonFinalResponses Counter32,
sipCommonStatsRetryDisconTime TimeStamp
}
sipCommonStatsRetryMethod OBJECT-TYPE
SYNTAX SipTCMethodName
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object uniquely identifies the SIP method related to the
objects in a row."
::= { sipCommonStatsRetryEntry 1 }
sipCommonStatsRetries OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the total number of request
retransmissions that have been sent by the SIP entity. Note
that there could be multiple retransmissions per request.
Discontinuities in the value of this counter can occur at
re-initialization of the SIP entity or service. A Management
Station can detect discontinuities in this counter by
monitoring the sipCommonStatsRetryDisconTime object in the same
row."
::= { sipCommonStatsRetryEntry 2 }
sipCommonStatsRetryFinalResponses OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the total number of Final Response retries
that have been sent by the SIP entity. Note that there could
be multiple retransmissions per request.
Discontinuities in the value of this counter can occur at
re-initialization of the SIP entity or service. A Management
Station can detect discontinuities in this counter by
Lingle, et al. Standards Track [Page 44]RFC 4780 SIP MIB Modules April 2007
monitoring the sipCommonStatsRetryDisconTime object in the same
row."
::= { sipCommonStatsRetryEntry 3 }
sipCommonStatsRetryNonFinalResponses OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the total number of non-Final Response
retries that have been sent by the SIP entity.
Discontinuities in the value of this counter can occur at
re-initialization of the SIP entity or service. A Management
Station can detect discontinuities in this counter by
monitoring the sipCommonStatsRetryDisconTime object in the same
row."
::= { sipCommonStatsRetryEntry 4 }
sipCommonStatsRetryDisconTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the sysUpTime object when the counters for the
retry statistics objects in this row last experienced a
discontinuity."
::= { sipCommonStatsRetryEntry 5 }
--
-- Other Common Statistics
--
sipCommonOtherStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF SipCommonOtherStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains other common statistics supported by each
SIP entity in this system."
::= { sipCommonOtherStats 1 }
sipCommonOtherStatsEntry OBJECT-TYPE
SYNTAX SipCommonOtherStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information on a particular SIP entity's other common
statistics.
Lingle, et al. Standards Track [Page 45]RFC 4780 SIP MIB Modules April 2007
Each row represents those objects for a particular SIP entity
present in this system. applIndex is used to uniquely identify
these instances of SIP entities and correlate them through
the common framework of the NETWORK-SERVICES-MIB (RFC 2788)."
INDEX { applIndex }
::= { sipCommonOtherStatsTable 1 }
SipCommonOtherStatsEntry ::= SEQUENCE {
sipCommonOtherStatsNumUnsupportedUris Counter32,
sipCommonOtherStatsNumUnsupportedMethods Counter32,
sipCommonOtherStatsOtherwiseDiscardedMsgs Counter32,
sipCommonOtherStatsDisconTime TimeStamp
}
sipCommonOtherStatsNumUnsupportedUris OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of RequestURIs received with an unsupported scheme.
A server normally responds to such requests with a 400 Bad
Request status code.
Discontinuities in the value of this counter can occur at
re-initialization of the SIP entity or service. A Management
Station can detect discontinuities in this counter by
monitoring the sipCommonOtherStatsDisconTime object in the same
row."
::= { sipCommonOtherStatsEntry 1 }
sipCommonOtherStatsNumUnsupportedMethods OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of SIP requests received with unsupported methods. A
server normally responds to such requests with a 501 (Not
Implemented) or 405 (Method Not Allowed).
Discontinuities in the value of this counter can occur at
re-initialization of the SIP entity or service. A Management
Station can detect discontinuities in this counter by
monitoring the sipCommonOtherStatsDisconTime object in the same
row."
::= { sipCommonOtherStatsEntry 2 }
sipCommonOtherStatsOtherwiseDiscardedMsgs OBJECT-TYPE
SYNTAX Counter32
Lingle, et al. Standards Track [Page 46]RFC 4780 SIP MIB Modules April 2007
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of SIP messages received that, for any number of
reasons, was discarded without a response.
Discontinuities in the value of this counter can occur at
re-initialization of the SIP entity or service. A Management
Station can detect discontinuities in this counter by
monitoring the sipCommonOtherStatsDisconTime object in the same
row."
::= { sipCommonOtherStatsEntry 3 }
sipCommonOtherStatsDisconTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the sysUpTime object when the counters for the
statistics objects in this row last experienced a
discontinuity."
::= { sipCommonOtherStatsEntry 4 }
--
-- Notification related objects
--
--
-- Status code related notification objects.
--
sipCommonStatusCodeNotifTo OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object contains the value of the To header in the message
containing the status code that caused the notification. The
header name will be part of this object value. For example,
'To: Watson '."
::= { sipCommonNotifObjects 1 }
sipCommonStatusCodeNotifFrom OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object contains the value of the From header in the
message containing the status code that caused the
Lingle, et al. Standards Track [Page 47]RFC 4780 SIP MIB Modules April 2007
notification. The header name will be part of this object
value. For example, 'From: Watson '."
::= { sipCommonNotifObjects 2 }
sipCommonStatusCodeNotifCallId OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object contains the value of the Call-ID in the message
containing the status code that caused the notification. The
header name will be part of this object value. For example,
'Call-ID: 5551212@example.com'."
::= { sipCommonNotifObjects 3 }
sipCommonStatusCodeNotifCSeq OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object contains the CSeq value in the message containing
the status code that caused the notification. The header name
will be part of this object value. For example, 'CSeq: 1722
INVITE'."
::= { sipCommonNotifObjects 4 }
--
-- General notification related objects.
--
sipCommonNotifApplIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..2147483647)
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object contains the applIndex as described in RFC 2788.
This object is created in order to allow a variable binding
containing a value of applIndex in a notification."
::= { sipCommonNotifObjects 5 }
sipCommonNotifSequenceNumber OBJECT-TYPE
SYNTAX Unsigned32 (1..2147483647)
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object contains a sequence number for each notification
generated by this SIP entity. Each notification SHOULD have a
unique sequence number. A network manager can use this
information to determine whether notifications from a
Lingle, et al. Standards Track [Page 48]RFC 4780 SIP MIB Modules April 2007
particular SIP entity have been missed. The value of this
object MUST start at 1 and increase by 1 with each generated
notification. If a system restarts, the sequence number MAY
start again from 1."
::= { sipCommonNotifObjects 6 }
--
-- Notifications
--
sipCommonStatusCodeNotif NOTIFICATION-TYPE
OBJECTS {
sipCommonNotifSequenceNumber,
sipCommonNotifApplIndex,
sipCommonStatusCodeNotifTo,
sipCommonStatusCodeNotifFrom,
sipCommonStatusCodeNotifCallId,
sipCommonStatusCodeNotifCSeq,
sipCommonStatusCodeIns,
sipCommonStatusCodeOuts
}
STATUS current
DESCRIPTION
"Signifies that a specific status code has been sent or received
by the system."
::= { sipCommonMIBNotifications 1 }
sipCommonStatusCodeThreshExceededInNotif NOTIFICATION-TYPE
OBJECTS {
sipCommonNotifSequenceNumber,
sipCommonNotifApplIndex,
sipCommonStatusCodeIns
}
STATUS current
DESCRIPTION
"Signifies that a specific status code was found to have been
received by the system frequently enough to exceed the
configured threshold. This notification can be used as
an early warning mechanism in lieu of using
sipCommonStatusCodeNotif."
::= { sipCommonMIBNotifications 2 }
sipCommonStatusCodeThreshExceededOutNotif NOTIFICATION-TYPE
OBJECTS {
sipCommonNotifSequenceNumber,
sipCommonNotifApplIndex,
sipCommonStatusCodeOuts
}
STATUS current
Lingle, et al. Standards Track [Page 49]RFC 4780 SIP MIB Modules April 2007
DESCRIPTION
"Signifies that a specific status code was found to have been
sent by the system enough to exceed the configured threshold.
This notification can be used as an early warning mechanism in
lieu of using sipCommonStatusCodeNotif."
::= { sipCommonMIBNotifications 3 }
sipCommonServiceColdStart NOTIFICATION-TYPE
OBJECTS {
sipCommonNotifSequenceNumber,
sipCommonNotifApplIndex,
sipCommonCfgServiceStartTime
}
STATUS current
DESCRIPTION
"Signifies that the SIP service has reinitialized itself or
started for the first time. This SHOULD result from a hard
'down' to 'up' administrative status change. The configuration
or behavior of the service MAY be altered."
::= { sipCommonMIBNotifications 4 }
sipCommonServiceWarmStart NOTIFICATION-TYPE
OBJECTS {
sipCommonNotifSequenceNumber,
sipCommonNotifApplIndex,
sipCommonCfgServiceLastChange
}
STATUS current
DESCRIPTION
"Signifies that the SIP service has reinitialized itself and is
restarting after an administrative 'reset'. The configuration
or behavior of the service MAY be altered."
::= { sipCommonMIBNotifications 5 }
sipCommonServiceStatusChanged NOTIFICATION-TYPE
OBJECTS {
sipCommonNotifSequenceNumber,
sipCommonNotifApplIndex,
sipCommonCfgServiceLastChange,
sipCommonCfgServiceOperStatus
}
STATUS current
DESCRIPTION
"Signifies that the SIP service operational status has changed."
::= { sipCommonMIBNotifications 6 }
--
-- Conformance
Lingle, et al. Standards Track [Page 50]RFC 4780 SIP MIB Modules April 2007
--
sipCommonMIBCompliances
OBJECT IDENTIFIER ::= { sipCommonMIBConformance 1 }
sipCommonMIBGroups
OBJECT IDENTIFIER ::= { sipCommonMIBConformance 2 }
--
-- Compliance Statements
--
sipCommonCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SIP entities."
MODULE -- this module
MANDATORY-GROUPS { sipCommonConfigGroup,
sipCommonStatsGroup
}
OBJECT sipCommonStatusCodeRowStatus
SYNTAX RowStatus { active(1) }
WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) }
DESCRIPTION
"Support for createAndWait and notInService is not required."
OBJECT sipCommonCfgServiceNotifEnable
MIN-ACCESS not-accessible
DESCRIPTION
"This object is optional and does not need to be supported."
GROUP sipCommonInformationalGroup
DESCRIPTION
"This group is OPTIONAL. A SIP entity can elect to not provide
any support for these objects, as they provide optional
information."
GROUP sipCommonConfigTimerGroup
DESCRIPTION
"This group is OPTIONAL. A SIP entity can elect to not provide
any timer configuration."
GROUP sipCommonStatsRetryGroup
DESCRIPTION
"This group is OPTIONAL. A SIP entity can elect to not provide
any retry statistics."
GROUP sipCommonNotifGroup
DESCRIPTION
Lingle, et al. Standards Track [Page 51]RFC 4780 SIP MIB Modules April 2007
"This group is OPTIONAL. A SIP entity can elect to not provide
any notifications. If implemented, the
sipCommonStatusCodeNotifGroup and sipCommonNotifObjectsGroup
MUST also be implemented."
GROUP sipCommonStatusCodeNotifGroup
DESCRIPTION
"This group is OPTIONAL. A SIP entity can elect to not provide
any notifications. If implemented, the sipCommonNotifGroup and
sipCommonNotifObjectsGroup MUST also be implemented."
GROUP sipCommonNotifObjectsGroup
DESCRIPTION
"This group is OPTIONAL. A SIP entity can elect to not provide
any notifications. If implemented, the
sipCommonStatusCodeNotifGroup and sipCommonNotifGroup MUST also
be implemented."
::= { sipCommonMIBCompliances 1 }
--
-- Units of Conformance
--
sipCommonConfigGroup OBJECT-GROUP
OBJECTS {
sipCommonCfgProtocolVersion,
sipCommonCfgServiceOperStatus,
sipCommonCfgServiceStartTime,
sipCommonCfgServiceLastChange,
sipCommonPortTransportRcv,
sipCommonOptionTag,
sipCommonOptionTagHeaderField,
sipCommonCfgMaxTransactions,
sipCommonCfgServiceNotifEnable,
sipCommonCfgEntityType,
sipCommonMethodSupportedName
}
STATUS current
DESCRIPTION
"A collection of objects providing configuration common to all
SIP entities."
::= { sipCommonMIBGroups 1 }
sipCommonInformationalGroup OBJECT-GROUP
OBJECTS {
sipCommonCfgOrganization
}
STATUS current
Lingle, et al. Standards Track [Page 52]RFC 4780 SIP MIB Modules April 2007
DESCRIPTION
"A collection of objects providing configuration common to all
SIP entities."
::= { sipCommonMIBGroups 2 }
sipCommonConfigTimerGroup OBJECT-GROUP
OBJECTS {
sipCommonCfgTimerA,
sipCommonCfgTimerB,
sipCommonCfgTimerC,
sipCommonCfgTimerD,
sipCommonCfgTimerE,
sipCommonCfgTimerF,
sipCommonCfgTimerG,
sipCommonCfgTimerH,
sipCommonCfgTimerI,
sipCommonCfgTimerJ,
sipCommonCfgTimerK,
sipCommonCfgTimerT1,
sipCommonCfgTimerT2,
sipCommonCfgTimerT4
}
STATUS current
DESCRIPTION
"A collection of objects providing timer configuration common to
all SIP entities."
::= { sipCommonMIBGroups 3 }
sipCommonStatsGroup OBJECT-GROUP
OBJECTS {
sipCommonSummaryInRequests,
sipCommonSummaryOutRequests,
sipCommonSummaryInResponses,
sipCommonSummaryOutResponses,
sipCommonSummaryTotalTransactions,
sipCommonSummaryDisconTime,
sipCommonMethodStatsOutbounds,
sipCommonMethodStatsInbounds,
sipCommonMethodStatsDisconTime,
sipCommonStatusCodeIns,
sipCommonStatusCodeOuts,
sipCommonStatusCodeRowStatus,
sipCommonStatusCodeDisconTime,
sipCommonTransCurrentactions,
sipCommonOtherStatsNumUnsupportedUris,
sipCommonOtherStatsNumUnsupportedMethods,
sipCommonOtherStatsOtherwiseDiscardedMsgs,
sipCommonOtherStatsDisconTime
Lingle, et al. Standards Track [Page 53]RFC 4780 SIP MIB Modules April 2007
}
STATUS current
DESCRIPTION
"A collection of objects providing statistics common to all SIP
entities."
::= { sipCommonMIBGroups 4 }
sipCommonStatsRetryGroup OBJECT-GROUP
OBJECTS {
sipCommonStatsRetries,
sipCommonStatsRetryFinalResponses,
sipCommonStatsRetryNonFinalResponses,
sipCommonStatsRetryDisconTime
}
STATUS current
DESCRIPTION
"A collection of objects providing retry statistics."
::= { sipCommonMIBGroups 5 }
sipCommonNotifGroup NOTIFICATION-GROUP
NOTIFICATIONS {
sipCommonStatusCodeNotif,
sipCommonStatusCodeThreshExceededInNotif,
sipCommonStatusCodeThreshExceededOutNotif,
sipCommonServiceColdStart,
sipCommonServiceWarmStart,
sipCommonServiceStatusChanged
}
STATUS current
DESCRIPTION
"A collection of notifications common to all SIP entities."
::= { sipCommonMIBGroups 6 }
sipCommonStatusCodeNotifGroup OBJECT-GROUP
OBJECTS {
sipCommonStatusCodeNotifSend,
sipCommonStatusCodeNotifEmitMode,
sipCommonStatusCodeNotifThresh,
sipCommonStatusCodeNotifInterval
}
STATUS current
DESCRIPTION
"A collection of objects related to the control and attribution
of notifications common to all SIP entities."
::= { sipCommonMIBGroups 7 }
sipCommonNotifObjectsGroup OBJECT-GROUP
Lingle, et al. Standards Track [Page 54]RFC 4780 SIP MIB Modules April 2007
OBJECTS {
sipCommonStatusCodeNotifTo,
sipCommonStatusCodeNotifFrom,
sipCommonStatusCodeNotifCallId,
sipCommonStatusCodeNotifCSeq,
sipCommonNotifApplIndex,
sipCommonNotifSequenceNumber
}
STATUS current
DESCRIPTION
"A collection of accessible-for-notify objects related to the
notification defined in this MIB module."
::= { sipCommonMIBGroups 8 }
END
7.3. SIP User Agent MIB Module
SIP-UA-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
Unsigned32,
mib-2
FROM SNMPv2-SMI -- RFC 2578
MODULE-COMPLIANCE,
OBJECT-GROUP
FROM SNMPv2-CONF -- RFC 2580
applIndex
FROM NETWORK-SERVICES-MIB -- RFC 2788
InetAddressType,
InetAddress
FROM INET-ADDRESS-MIB -- RFC 4001
SipTCEntityRole
FROM SIP-TC-MIB; -- RFC 4780
sipUAMIB MODULE-IDENTITY
LAST-UPDATED "200704200000Z"
ORGANIZATION "IETF Session Initiation Protocol Working Group"
CONTACT-INFO
"SIP WG email: sip@ietf.org
Co-editor Kevin Lingle
Lingle, et al. Standards Track [Page 55]RFC 4780 SIP MIB Modules April 2007
Cisco Systems, Inc.
postal: 7025 Kit Creek Road
P.O. Box 14987
Research Triangle Park, NC 27709
USA
email: klingle@cisco.com
phone: +1 919 476 2029
Co-editor Joon Maeng
email: jmaeng@austin.rr.com
Co-editor Jean-Francois Mule
CableLabs
postal: 858 Coal Creek Circle
Louisville, CO 80027
USA
email: jf.mule@cablelabs.com
phone: +1 303 661 9100
Co-editor Dave Walker
email: drwalker@rogers.com"
DESCRIPTION
"Session Initiation Protocol (SIP) User Agent (UA) MIB module.
SIP is an application-layer signaling protocol for creating,
modifying, and terminating multimedia sessions with one or more
participants. These sessions include Internet multimedia
conferences and Internet telephone calls. SIP is defined in
RFC 3261 (June 2002).
A User Agent is an application that contains both a User Agent
Client (UAC) and a User Agent Server (UAS). A UAC is an
application that initiates a SIP request. A UAS is an
application that contacts the user when a SIP request is
received and that returns a response on behalf of the user.
The response accepts, rejects, or redirects the request.
Copyright (C) The IETF Trust (2007). This version of
this MIB module is part of RFC 4780; see the RFC itself for
full legal notices."
REVISION "200704200000Z"
DESCRIPTION
"Initial version of the IETF SIP-UA-MIB module. This version
published as part of RFC 4780."
::= { mib-2 150 }
-- Top-Level Components of this MIB.
sipUAMIBObjects OBJECT IDENTIFIER ::= { sipUAMIB 1 }
Lingle, et al. Standards Track [Page 56]RFC 4780 SIP MIB Modules April 2007
sipUAMIBConformance OBJECT IDENTIFIER ::= { sipUAMIB 2 }
--
-- This MIB contains objects related to SIP User Agents.
--
sipUACfgServer OBJECT IDENTIFIER ::= { sipUAMIBObjects 1 }
--
-- SIP Server Configuration
--
sipUACfgServerTable OBJECT-TYPE
SYNTAX SEQUENCE OF SipUACfgServerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains SIP server configuration objects applicable
to each SIP user agent in this system."
::= { sipUACfgServer 1 }
sipUACfgServerEntry OBJECT-TYPE
SYNTAX SipUACfgServerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row of server configuration.
Each row represents those objects for a particular SIP user
agent present in this system. applIndex is used to uniquely
identify these instances of SIP user agents and correlate
them through the common framework of the NETWORK-SERVICES-MIB
(RFC 2788). The same value of applIndex used in the
corresponding SIP-COMMON-MIB is used here."
INDEX { applIndex, sipUACfgServerIndex }
::= { sipUACfgServerTable 1 }
SipUACfgServerEntry ::= SEQUENCE {
sipUACfgServerIndex Unsigned32,
sipUACfgServerAddressType InetAddressType,
sipUACfgServerAddress InetAddress,
sipUACfgServerRole SipTCEntityRole
}
sipUACfgServerIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique identifier of a server address when multiple addresses
Lingle, et al. Standards Track [Page 57]RFC 4780 SIP MIB Modules April 2007
are configured by the SIP entity. If one address isn't
reachable, then another can be tried."
::= { sipUACfgServerEntry 1 }
sipUACfgServerAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the type of address contained in the
associated instance of sipUACfgServerAddress."
REFERENCE
"INET-ADDRESS-MIB (RFC 4001)"
::= { sipUACfgServerEntry 2 }
sipUACfgServerAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the address of a SIP server this user
agent will use to proxy/redirect calls. The type of this
address is determined by the value of the
sipUACfgServerAddressType object."
REFERENCE "INET-ADDRESS-MIB (RFC 4001)"
::= { sipUACfgServerEntry 3 }
sipUACfgServerRole OBJECT-TYPE
SYNTAX SipTCEntityRole
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the function of the SIP server this user
agent should communicate with: registrar, proxy (outbound
proxy), etc."
::= { sipUACfgServerEntry 4 }
--
-- Conformance
--
sipUAMIBCompliances OBJECT IDENTIFIER ::= { sipUAMIBConformance 1 }
sipUAMIBGroups OBJECT IDENTIFIER ::= { sipUAMIBConformance 2 }
--
-- Compliance Statements
--
sipUACompliance MODULE-COMPLIANCE
STATUS current
Lingle, et al. Standards Track [Page 58]RFC 4780 SIP MIB Modules April 2007
DESCRIPTION
"The compliance statement for SIP entities that implement the
SIP-UA-MIB module."
MODULE -- this module
MANDATORY-GROUPS { sipUAConfigGroup }
::= { sipUAMIBCompliances 1 }
--
-- Units of Conformance
--
sipUAConfigGroup OBJECT-GROUP
OBJECTS {
sipUACfgServerAddressType,
sipUACfgServerAddress,
sipUACfgServerRole
}
STATUS current
DESCRIPTION
"A collection of objects providing information about the
configuration of SIP User Agents."
::= { sipUAMIBGroups 1 }
END
7.4. SIP Server MIB Module (Proxy, Redirect, and Registrar Servers)
SIP-SERVER-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
Counter32,
Unsigned32,
Gauge32,
mib-2
FROM SNMPv2-SMI -- RFC 2578
TruthValue,
TimeStamp, DateAndTime
FROM SNMPv2-TC -- RFC 2579
MODULE-COMPLIANCE,
OBJECT-GROUP
FROM SNMPv2-CONF -- RFC 2580
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB -- RFC 3411
Lingle, et al. Standards Track [Page 59]RFC 4780 SIP MIB Modules April 2007
applIndex
FROM NETWORK-SERVICES-MIB -- RFC 2788
InetAddressType,
InetAddress
FROM INET-ADDRESS-MIB; -- RFC 4001
sipServerMIB MODULE-IDENTITY
LAST-UPDATED "200704200000Z"
ORGANIZATION "IETF Session Initiation Protocol
Working Group"
CONTACT-INFO
"SIP WG email: sip@ietf.org
Co-editor: Kevin Lingle
Cisco Systems, Inc.
postal: 7025 Kit Creek Road
P.O. Box 14987
Research Triangle Park, NC 27709
USA
email: klingle@cisco.com
phone: +1 919 476 2029
Co-editor: Joon Maeng
email: jmaeng@austin.rr.com
Co-editor: Jean-Francois Mule
CableLabs
postal: 858 Coal Creek Circle
Louisville, CO 80027
USA
email: jf.mule@cablelabs.com
phone: +1 303 661 9100
Co-editor: Dave Walker
email: drwalker@rogers.com
"
DESCRIPTION
"Session Initiation Protocol (SIP) Server MIB module. SIP is an
application-layer signaling protocol for creating, modifying,
and terminating multimedia sessions with one or more
participants. These sessions include Internet multimedia
conferences and Internet telephone calls. SIP is defined in
RFC 3261 (June 2002).
This MIB is defined for the management of SIP Proxy, Redirect,
and Registrar Servers.
Lingle, et al. Standards Track [Page 60]RFC 4780 SIP MIB Modules April 2007
A Proxy Server acts as both a client and a server. It accepts
requests from other clients, either responding to them or
passing them on to other servers, possibly after modification.
A Redirect Server accepts requests from clients and returns
zero or more addresses to that client. Unlike a User Agent
Server, it does not accept calls.
A Registrar is a server that accepts REGISTER requests. A
Registrar is typically co-located with a Proxy or Redirect
Server.
Copyright (C) The IETF Trust (2007). This version of
this MIB module is part of RFC 4780; see the RFC itself for
full legal notices."
REVISION "200704200000Z"
DESCRIPTION
"Initial version of the IETF SIP-SERVER-MIB module. This
version published as part of RFC 4780."
::= { mib-2 151 }
-- Top-Level Components of this MIB.
sipServerMIBObjects OBJECT IDENTIFIER ::= { sipServerMIB 1 }
sipServerMIBConformance OBJECT IDENTIFIER ::= { sipServerMIB 2 }
--
-- These groups contain objects common to all SIP servers.
--
sipServerCfg OBJECT IDENTIFIER ::= { sipServerMIBObjects 1 }
--
-- Common Server Configuration Objects
--
sipServerCfgTable OBJECT-TYPE
SYNTAX SEQUENCE OF SipServerCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains configuration objects applicable to SIP
Redirect and Proxy Servers."
::= { sipServerCfg 1 }
sipServerCfgEntry OBJECT-TYPE
SYNTAX SipServerCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
Lingle, et al. Standards Track [Page 61]RFC 4780 SIP MIB Modules April 2007
"A row of common configuration.
Each row represents those objects for a particular SIP server
present in this system. applIndex is used to uniquely identify
these instances of SIP servers and correlate them through
the common framework of the NETWORK-SERVICES-MIB (RFC 2788).
The same value of applIndex used in the corresponding
SIP-COMMON-MIB is used here."
INDEX { applIndex }
::= { sipServerCfgTable 1 }
SipServerCfgEntry ::=
SEQUENCE {
sipServerCfgHostAddressType InetAddressType,
sipServerCfgHostAddress InetAddress
}
sipServerCfgHostAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of Internet address by which the SIP server is
reachable."
REFERENCE
"RFC 3261, Section 19.1.1"
::= { sipServerCfgEntry 1 }
sipServerCfgHostAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This is the host portion of a SIP URI that is assigned to the
SIP server. It MAY contain a fully qualified domain name or
an IP address. The length of the value will depend on the type
of address specified. The type of address given by this object
is controlled by sipServerCfgHostAddressType."
REFERENCE
"RFC 3261, Section 19.1.1"
::= { sipServerCfgEntry 2 }
--
-- This group contains MIB objects
-- related to SIP Proxy Servers.
--
sipServerProxyCfg OBJECT IDENTIFIER ::= { sipServerMIBObjects 3 }
Lingle, et al. Standards Track [Page 62]RFC 4780 SIP MIB Modules April 2007
sipServerProxyStats OBJECT IDENTIFIER ::= { sipServerMIBObjects 4 }
--
-- Proxy Server Configuration
--
sipServerProxyCfgTable OBJECT-TYPE
SYNTAX SEQUENCE OF SipServerProxyCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains configuration objects applicable to SIP
Proxy Servers."
::= { sipServerProxyCfg 1 }
sipServerProxyCfgEntry OBJECT-TYPE
SYNTAX SipServerProxyCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row of common proxy configuration.
Each row represents those objects for a particular SIP server
present in this system. applIndex is used to uniquely identify
these instances of SIP servers and correlate them through the
common framework of the NETWORK-SERVICES-MIB (RFC 2788). The
same value of applIndex used in the corresponding
SIP-COMMON-MIB is used here."
INDEX { applIndex }
::= { sipServerProxyCfgTable 1 }
SipServerProxyCfgEntry ::=
SEQUENCE {
sipServerCfgProxyStatefulness INTEGER,
sipServerCfgProxyRecursion TruthValue,
sipServerCfgProxyRecordRoute TruthValue,
sipServerCfgProxyAuthMethod BITS,
sipServerCfgProxyAuthDefaultRealm SnmpAdminString
}
sipServerCfgProxyStatefulness OBJECT-TYPE
SYNTAX INTEGER {
stateless(1),
transactionStateful(2),
callStateful(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Lingle, et al. Standards Track [Page 63]RFC 4780 SIP MIB Modules April 2007
"This object reflects the default mode of operation for the
Proxy Server entity.
A stateless proxy is a logical entity that does not maintain
the client or server transaction state machines when it
processes requests. A stateless proxy forwards every request it
receives downstream and every response it receives upstream. If
the value of this object is stateless(1), the proxy defaults to
stateless operations.
A transaction stateful proxy, or simply a 'stateful proxy', is
a logical entity that maintains the client and server
transaction state machines during the processing of a request.
A (transaction) stateful proxy is not the same as a call
stateful proxy. If the value of this object is
transactionStateful(2), the proxy is stateful on a transaction
basis.
A call stateful proxy is a logical entity if it retains state
for a dialog from the initiating INVITE to the terminating BYE
request. A call stateful proxy is always transaction stateful,
but the converse is not necessarily true. If the value of this
object is callStateful(3), the proxy is call stateful."
REFERENCE
"RFC 3261, Section 16"
::= { sipServerProxyCfgEntry 1 }
sipServerCfgProxyRecursion OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects whether or not the Proxy performs a
recursive search on the Contacts provided in 3xx redirects.
If the value of this object is 'true', a recursive search is
performed. If the value is 'false', no search is performed,
and the 3xx response is sent upstream towards the source of
the request."
REFERENCE
"RFC 3261 Sections 16.5 and 16.6"
::= { sipServerProxyCfgEntry 2 }
sipServerCfgProxyRecordRoute OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
Lingle, et al. Standards Track [Page 64]RFC 4780 SIP MIB Modules April 2007
DESCRIPTION
"This object reflects whether or not the proxy adds itself to
the Record-Route header as a default action. This header is
used to list the proxies that insist on being in the signaling
path for subsequent requests related to the call leg.
If the value of this object is 'true', the proxy adds itself to
the end of the Record-Route header, creating the header if
required. If the value is 'false', the proxy does not add
itself to the Record-Route header."
REFERENCE
"RFC 3261, Section 20.30"
::= { sipServerProxyCfgEntry 3 }
--
-- Security
--
sipServerCfgProxyAuthMethod OBJECT-TYPE
SYNTAX BITS {
none(0),
tls(1),
digest(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the authentication methods that MAY be
used to authenticate request originators.
bit 0 no authentication is performed
bit 1 TLS is used
bit 2 HTTP Digest is used."
REFERENCE
"RFC 3261 Sections 22, 23, 26, 26.2.3"
::= { sipServerProxyCfgEntry 4 }
sipServerCfgProxyAuthDefaultRealm OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the default realm value used in
Proxy-Authenticate headers. Note that this MAY need to be
stored per user, in which case, this default value is ignored.
"
REFERENCE
"RFC 3261, Section 22.1"
::= { sipServerProxyCfgEntry 5 }
Lingle, et al. Standards Track [Page 65]RFC 4780 SIP MIB Modules April 2007
--
-- Proxy Server Statistics
--
sipServerProxyStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF SipServerProxyStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the statistics objects applicable to all
SIP Proxy Servers in this system."
::= { sipServerProxyStats 1 }
sipServerProxyStatsEntry OBJECT-TYPE
SYNTAX SipServerProxyStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row of summary statistics.
Each row represents those objects for a particular SIP server
present in this system. applIndex is used to uniquely identify
these instances of SIP servers and correlate them through the
common framework of the NETWORK-SERVICES-MIB (RFC 2788). The
same value of applIndex used in the corresponding
SIP-COMMON-MIB is used here."
INDEX { applIndex }
::= { sipServerProxyStatsTable 1 }
SipServerProxyStatsEntry ::=
SEQUENCE {
sipServerProxyStatProxyReqFailures Counter32,
sipServerProxyStatsDisconTime TimeStamp
}
sipServerProxyStatProxyReqFailures OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the number of occurrences of unsupported
options being specified in received Proxy-Require headers.
Such occurrences result in a 420 Bad Extension status code
being returned.
Discontinuities in the value of this counter can occur at
re-initialization of the SIP entity or service. A Management
Station can detect discontinuities in this counter by
Lingle, et al. Standards Track [Page 66]RFC 4780 SIP MIB Modules April 2007
monitoring the sipServerProxyStatsDisconTime object in the same
row."
::= { sipServerProxyStatsEntry 1 }
sipServerProxyStatsDisconTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the sysUpTime object when the counters for the server
statistics objects in this row last experienced a discontinuity."
::= { sipServerProxyStatsEntry 2 }
--
-- This group contains MIB objects related to SIP Registrars.
--
sipServerRegCfg OBJECT IDENTIFIER ::= { sipServerMIBObjects 5 }
sipServerRegStats OBJECT IDENTIFIER ::= { sipServerMIBObjects 6 }
--
-- Registrar Configuration
--
sipServerRegCfgTable OBJECT-TYPE
SYNTAX SEQUENCE OF SipServerRegCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains configuration objects applicable to SIP
Registrars."
::= { sipServerRegCfg 1 }
sipServerRegCfgEntry OBJECT-TYPE
SYNTAX SipServerRegCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row of common Registrar configuration.
Each row represents those objects for a particular SIP server
present in this system. applIndex is used to uniquely identify
these instances of SIP servers and correlate them through the
common framework of the NETWORK-SERVICES-MIB (RFC 2788). The
same value of applIndex used in the corresponding
SIP-COMMON-MIB is used here."
INDEX { applIndex }
::= { sipServerRegCfgTable 1 }
SipServerRegCfgEntry ::=
Lingle, et al. Standards Track [Page 67]RFC 4780 SIP MIB Modules April 2007
SEQUENCE {
sipServerRegMaxContactExpiryDuration Unsigned32,
sipServerRegMaxUsers Unsigned32,
sipServerRegCurrentUsers Gauge32,
sipServerRegDfltRegActiveInterval Unsigned32
}
sipServerRegMaxContactExpiryDuration OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the maximum expiry that may be requested
by a User Agent for a particular Contact. User Agents can
specify expiry using either an Expiry header in a REGISTER
request, or using an Expires parameter in a Contact header in
a REGISTER request. If the value requested by the User Agent
is greater than the value of this object, then the contact
information is given the duration specified by this object, and
that duration is indicated to the User Agent in the response."
::= { sipServerRegCfgEntry 1 }
sipServerRegMaxUsers OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the maximum number of users that the
Registrar supports. The current number of users is reflected
by sipServerRegCurrentUsers."
::= { sipServerRegCfgEntry 2 }
sipServerRegCurrentUsers OBJECT-TYPE
SYNTAX Gauge32 (0..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the number of users currently registered
with the Registrar."
::= { sipServerRegCfgEntry 3 }
sipServerRegDfltRegActiveInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Lingle, et al. Standards Track [Page 68]RFC 4780 SIP MIB Modules April 2007
"This object reflects the default time interval the Registrar
considers registrations to be active. The value is used to
compute the Expires header in the REGISTER response. If a user
agent requests a time interval shorter than specified by this
object, the Registrar SHOULD honor that request. If a Contact
entry does not have an 'expires' parameter, the value of the
Expires header field is used instead. If a Contact entry has no
'expires' parameter and no Expires header field is present,
the value of this object is used as the default value."
REFERENCE
"RFC 3261, Section 10.2"
::= { sipServerRegCfgEntry 4 }
--
-- Per User Information
--
sipServerRegUserTable OBJECT-TYPE
SYNTAX SEQUENCE OF SipServerRegUserEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information on all users registered to each
Registrar in this system."
::= { sipServerRegCfg 2 }
sipServerRegUserEntry OBJECT-TYPE
SYNTAX SipServerRegUserEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This entry contains information for a single user registered to
this Registrar.
Each row represents those objects for a particular SIP server
present in this system. applIndex is used to uniquely identify
these instances of SIP servers and correlate them through the
common framework of the NETWORK-SERVICES-MIB (RFC 2788). The
same value of applIndex used in the corresponding
SIP-COMMON-MIB is used here."
INDEX { applIndex, sipServerRegUserIndex }
::= { sipServerRegUserTable 1 }
SipServerRegUserEntry ::=
SEQUENCE {
sipServerRegUserIndex Unsigned32,
sipServerRegUserUri SnmpAdminString,
sipServerRegUserAuthenticationFailures Counter32,
sipServerRegUserDisconTime TimeStamp
}
Lingle, et al. Standards Track [Page 69]RFC 4780 SIP MIB Modules April 2007
sipServerRegUserIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object uniquely identifies a conceptual row in the table."
::= { sipServerRegUserEntry 1 }
sipServerRegUserUri OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the user's address-of-record. It is the
main form by which the Registrar knows the user. The format is
typically 'user@domain'. It is contained in the To header for
all REGISTER requests."
::= { sipServerRegUserEntry 2 }
sipServerRegUserAuthenticationFailures OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains a count of the number of times the user
has failed authentication.
Discontinuities in the value of this counter can occur due to
successful user authentications and at re-initialization of
the SIP entity or service. A Management Station can detect
discontinuities in this counter by monitoring the
sipServerRegUserDisconTime object in the same row."
::= { sipServerRegUserEntry 3 }
sipServerRegUserDisconTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the sysUpTime object when the counters for the
user registration statistics objects in this row last
experienced a discontinuity."
::= { sipServerRegUserEntry 4 }
--
-- Per Contact Information
--
sipServerRegContactTable OBJECT-TYPE
SYNTAX SEQUENCE OF SipServerRegContactEntry
Lingle, et al. Standards Track [Page 70]RFC 4780 SIP MIB Modules April 2007
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information on every location where a
registered user (specified by sipServerRegUserIndex) wishes to
be found (i.e., the user has provided contact information to
each SIP Registrar in this system)."
::= { sipServerRegCfg 3 }
sipServerRegContactEntry OBJECT-TYPE
SYNTAX SipServerRegContactEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This entry contains information for a single Contact. Multiple
contacts may exist for a single user.
Each row represents those objects for a particular SIP server
present in this system. applIndex is used to uniquely identify
these instances of SIP servers and correlate them through the
common framework of the NETWORK-SERVICES-MIB (RFC 2788). The
same value of applIndex used in the corresponding
SIP-COMMON-MIB is used here."
INDEX { applIndex,
sipServerRegUserIndex,
sipServerRegContactIndex
}
::= { sipServerRegContactTable 1 }
SipServerRegContactEntry ::=
SEQUENCE {
sipServerRegContactIndex Unsigned32,
sipServerRegContactDisplayName SnmpAdminString,
sipServerRegContactURI SnmpAdminString,
sipServerRegContactLastUpdated TimeStamp,
sipServerRegContactExpiry DateAndTime,
sipServerRegContactPreference SnmpAdminString
}
sipServerRegContactIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Along with the sipServerRegUserIndex, this object uniquely
identifies a conceptual row in the table."
::= { sipServerRegContactEntry 1 }
Lingle, et al. Standards Track [Page 71]RFC 4780 SIP MIB Modules April 2007
sipServerRegContactDisplayName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the display name for the Contact. For
example, 'Santa at Home', or 'Santa on his Sled', corresponding
to contact URIs of sip:BigGuy@example.com or
sip:sclaus817@example.com, respectively."
::= { sipServerRegContactEntry 2 }
sipServerRegContactURI OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains either a SIP URI where the user can be
contacted. This URI is normally returned to a client from a
Redirect Server, or is used as the RequestURI in a SIP request
line for requests forwarded by a proxy."
::= { sipServerRegContactEntry 3 }
sipServerRegContactLastUpdated OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the time when this contact information
was accepted. If the contact information is updated via a
subsequent REGISTER of the same information, this object is
also updated."
::= { sipServerRegContactEntry 4 }
sipServerRegContactExpiry OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the date and time when the contact
information will no longer be valid. Such times may be
specified by the user at registration (i.e., Expires header or
expiry parameter in the Contact information), or a system
default can be applied."
::= { sipServerRegContactEntry 5 }
sipServerRegContactPreference OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
Lingle, et al. Standards Track [Page 72]RFC 4780 SIP MIB Modules April 2007
STATUS current
DESCRIPTION
"This object indicates a relative preference for the particular
Contact header field value compared to other bindings for this
address-of-record. A registering user may provide this
preference as a 'qvalue' parameter in the Contact header.
The format of this item is a decimal number between 0 and 1
(for example 0.9). Higher values indicate locations preferred
by the user."
REFERENCE
"RFC 3261, Section 10.2.1.2, 16.6, and 20.10"
::= { sipServerRegContactEntry 6 }
--
-- Registrar Statistics
--
sipServerRegStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF SipServerRegStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the summary statistics objects applicable
to all SIP Registrars in this system."
::= { sipServerRegStats 1 }
sipServerRegStatsEntry OBJECT-TYPE
SYNTAX SipServerRegStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row of summary statistics.
Each row represents those objects for a particular SIP server
present in this system. applIndex is used to uniquely identify
these instances of SIP servers and correlate them through the
common framework of the NETWORK-SERVICES-MIB (RFC 2788). The
same value of applIndex used in the corresponding
SIP-COMMON-MIB is used here."
INDEX { applIndex }
::= { sipServerRegStatsTable 1 }
SipServerRegStatsEntry ::=
SEQUENCE {
sipServerRegStatsAcceptedRegs Counter32,
sipServerRegStatsRejectedRegs Counter32,
sipServerRegStatsDisconTime TimeStamp
}
Lingle, et al. Standards Track [Page 73]RFC 4780 SIP MIB Modules April 2007
sipServerRegStatsAcceptedRegs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains a count of the number of REGISTER requests
that have been accepted (status code 200) by the Registrar.
This includes additions of new contact information, refreshing
contact information, as well as requests for deletion of
contact information.
Discontinuities in the value of this counter can occur at
re-initialization of the SIP entity or service. A Management
Station can detect discontinuities in this counter by
monitoring the sipServerRegStatsDisconTime object in the same
row."
::= { sipServerRegStatsEntry 1 }
sipServerRegStatsRejectedRegs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains a count of the number REGISTER requests
that have been rejected by the Registrar.
Discontinuities in the value of this counter can occur at
re-initialization of the SIP entity or service. A Management
Station can detect discontinuities in this counter by
monitoring the sipServerRegStatsDisconTime object in the same
row."
::= { sipServerRegStatsEntry 2 }
sipServerRegStatsDisconTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the sysUpTime object when the counters for the
registrar statistics objects in this row last experienced a
discontinuity."
::= { sipServerRegStatsEntry 3 }
--
-- Conformance
--
sipServerMIBCompliances
OBJECT IDENTIFIER ::= { sipServerMIBConformance 1 }
Lingle, et al. Standards Track [Page 74]RFC 4780 SIP MIB Modules April 2007
sipServerMIBGroups
OBJECT IDENTIFIER ::= { sipServerMIBConformance 2 }
--
-- Compliance Statements
--
sipServerProxyServerCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SIP entities acting as Proxy
Servers."
MODULE -- this module
MANDATORY-GROUPS { sipServerConfigGroup,
sipServerProxyConfigGroup,
sipServerProxyStatsGroup
}
::= { sipServerMIBCompliances 1 }
sipRedirectServerCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SIP entities acting as Redirect
Servers."
MODULE -- this module
MANDATORY-GROUPS { sipServerConfigGroup }
::= { sipServerMIBCompliances 2 }
sipServerRegistrarServerCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SIP entities acting as
Registrars."
MODULE -- this module
MANDATORY-GROUPS { sipServerConfigGroup,
sipServerRegistrarConfigGroup,
sipServerRegistrarStatsGroup }
GROUP sipServerRegistrarUsersGroup
DESCRIPTION
"This is an optional group."
::= { sipServerMIBCompliances 3 }
--
-- Units of Conformance
--
sipServerConfigGroup OBJECT-GROUP
OBJECTS {
sipServerCfgHostAddressType,
sipServerCfgHostAddress
Lingle, et al. Standards Track [Page 75]RFC 4780 SIP MIB Modules April 2007
}
STATUS current
DESCRIPTION
"A collection of objects providing configuration common to SIP
Proxy and Redirect servers."
::= { sipServerMIBGroups 1 }
sipServerProxyConfigGroup OBJECT-GROUP
OBJECTS {
sipServerCfgProxyStatefulness,
sipServerCfgProxyRecursion,
sipServerCfgProxyRecordRoute,
sipServerCfgProxyAuthMethod,
sipServerCfgProxyAuthDefaultRealm
}
STATUS current
DESCRIPTION
"A collection of objects providing configuration for SIP Proxy
servers."
::= { sipServerMIBGroups 2 }
sipServerProxyStatsGroup OBJECT-GROUP
OBJECTS {
sipServerProxyStatProxyReqFailures,
sipServerProxyStatsDisconTime
}
STATUS current
DESCRIPTION
"A collection of objects providing statistics for SIP Proxy
servers."
::= { sipServerMIBGroups 3 }
sipServerRegistrarConfigGroup OBJECT-GROUP
OBJECTS {
sipServerRegMaxContactExpiryDuration,
sipServerRegMaxUsers,
sipServerRegCurrentUsers,
sipServerRegDfltRegActiveInterval
}
STATUS current
DESCRIPTION
"A collection of objects providing configuration for SIP
Registrars."
::= { sipServerMIBGroups 4 }
sipServerRegistrarStatsGroup OBJECT-GROUP
OBJECTS {
sipServerRegStatsAcceptedRegs,
Lingle, et al. Standards Track [Page 76]RFC 4780 SIP MIB Modules April 2007
sipServerRegStatsRejectedRegs,
sipServerRegStatsDisconTime
}
STATUS current
DESCRIPTION
"A collection of objects providing statistics for SIP
Registrars."
::= { sipServerMIBGroups 5 }
sipServerRegistrarUsersGroup OBJECT-GROUP
OBJECTS {
sipServerRegUserUri,
sipServerRegUserAuthenticationFailures,
sipServerRegUserDisconTime,
sipServerRegContactDisplayName,
sipServerRegContactURI,
sipServerRegContactLastUpdated,
sipServerRegContactExpiry,
sipServerRegContactPreference
}
STATUS current
DESCRIPTION
"A collection of objects related to registered users."
::= { sipServerMIBGroups 6 }
END
8. IANA Considerations
The MIB modules defined in this document use the following IANA-
assigned OBJECT IDENTIFIER values recorded in the SMI Numbers
registry:
+--------------+-------------------------+
| Descriptor | OBJECT IDENTIFIER value |
+--------------+-------------------------+
| sipTC | { mib-2 148 } |
| sipCommonMIB | { mib-2 149 } |
| sipUAMIB | { mib-2 150 } |
| sipServerMIB | { mib-2 151 } |
+--------------+-------------------------+
Lingle, et al. Standards Track [Page 77]RFC 4780 SIP MIB Modules April 2007
9. Security Considerations
There are a number of management objects defined in the SIP-COMMON-
MIB MIB module with a MAX-ACCESS clause of read-write and/or read-
create. Such objects may be considered sensitive or vulnerable in
some network environments. The support for SET operations in a non-
secure environment without proper protection can have a negative
effect on network operations.
The following read-create object in SIP-COMMON-MIB is used to
configure the status code statistics that will be monitored by the
SIP entity:
sipCommonStatusCodeRowStatus:
If this object is SET maliciously, it may result in an over-
allocation of resources in a system for the purpose of
accumulating and maintaining statistics.
The following read-write objects in SIP-COMMON-MIB are used to
configure the behavior of certain SNMP notifications potentially
generated by a SIP entity:
sipCommonStatusCodeNotifSend, sipCommonStatusCodeNotifEmitMode,
sipCommonStatusCodeNotifThresh, sipCommonStatusCodeNotifInterval,
sipCommonCfgServiceNotifEnable:
If these objects are SET maliciously, it may result in a system
and/or network performance impact due to the generation of SNMP
notifications.
Some of the readable objects in the MIB modules (i.e., objects with a
MAX-ACCESS other than not-accessible) may be considered sensitive or
vulnerable in some network environments. It is thus important to
control even GET and/or NOTIFY access to these objects and possibly
to even encrypt the values of these objects when sending them over
the network via SNMP.
The following object values may contain private or confidential
customer information like first name, last name, customer
identification, location, company affiliation, the time the
information was updated, etc.
sipServerRegContactDisplayName, sipServerRegContactURI,
sipServerRegContactLastUpdated and sipCommonCfgOrganization.
Lingle, et al. Standards Track [Page 78]RFC 4780 SIP MIB Modules April 2007
The sipCommonCfgTable table contains some objects that may help
attackers gain knowledge about the status and operations of the SIP
service. In particular, the object value of
sipCommonCfgServiceOperStatus may indicate that the SIP entity is in
congested state and may lead attackers to build additional service
attacks to overload the system.
The sipCommonCfgEntityType object indicates the type of SIP entity,
and the sipCommonMethodSupportedTable table contains in the SIP-
COMMON-MIB MIB module list of SIP methods supported by each entity in
the system. Gaining access to this information may allow attackers
to build method-specific attacks or use unsupported methods to create
denial-of-service attack scenarios.
In the SIP-UA-MIB MIB module, the sipUACfgServerTable contains the
address of the SIP servers providing services to the UA, and
obtaining this information may disclose some private or sensitive
information about the SIP service usage.
In the SIP-SERVER-MIB MIB module, the sipServerCfgProxyAuthMethod
object defines the authentication methods supported by the server and
may be used to build specific denial-of-service attackers targeted at
the security mechanisms employed by the SIP entity.
SNMP versions prior to SNMPv3 did not include adequate security.
Even if the network itself is secure (for example by using IPsec),
even then, there is no control as to who on the secure network is
allowed to access and GET/SET (read/change/create/delete) the objects
in this set of MIB modules.
It is RECOMMENDED that implementers consider the security features as
provided by the SNMPv3 framework (see RFC 3410 [RFC3410]), including
full support for the SNMPv3 cryptographic mechanisms (for
authentication and privacy).
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsi when bility to ensure that the SNMP entity giving access to
an instance of this MIB module is properly configured to give access
to the objects only to those principals (users) that have legitimate
rights to indeed GET or SET (change/create/delete) them.
Lingle, et al. Standards Track [Page 79]
RFC 4780 SIP MIB Modules April 2007
10. Contributor Acknowledgments
We wish to thank the members of the IETF SIP and SIPPING working
groups, and the SIP-MIB Design team for their comments and
suggestions. Detailed comments were provided by Tom Taylor, Kavitha
Patchayappan, Dan Romascanu, Cullen Jennings, Orit Levin, AC
Mahendran, Mary Barnes, Rohan Mahy, Bob Penfield, Charles Eckel, and
Dean Willis. Special thanks to Bert Wijnen for his expert reviews,
which have greatly improved the SIP MIB modules.
11. References
11.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3261] Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston,
A., Peterson, J., Sparks, R., Handley, M., and E.
Schooler, "SIP: Session Initiation Protocol", RFC 3261,
June 2002.
[RFC2578] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Structure of Management Information Version 2 (SMIv2)",
STD 58, RFC 2578, April 1999.
[RFC2579] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Textual Conventions for SMIv2", STD 58, RFC 2579, April
1999.
[RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Conformance Statements for SMIv2", STD 58, RFC 2580,
April 1999.
[RFC2788] Freed, N. and S. Kille, "Network Services Monitoring MIB",
RFC 2788, March 2000.
[RFC3411] Harrington, D., Presuhn, R., and B. Wijnen, "An
Architecture for Describing Simple Network Management
Protocol (SNMP) Management Frameworks", STD 62, RFC 3411,
December 2002.
[RFC4001] Daniele, M., Haberman, B., Routhier, S., and J.
Schoenwaelder, "Textual Conventions for Internet Network
Addresses", RFC 4001, February 2005.
Lingle, et al. Standards Track [Page 80]RFC 4780 SIP MIB Modules April 2007
11.2. Informative References
[RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction and Applicability Statements for Internet-
Standard Management Framework", RFC 3410, December 2002.
[RFC3262] Rosenberg, J. and H. Schulzrinne, "Reliability of
Provisional Responses in Session Initiation Protocol
(SIP)", RFC 3262, June 2002.
[RFC4168] Rosenberg, J., Schulzrinne, H., and G. Camarillo, "The
Stream Control Transmission Protocol (SCTP) as a Transport
for the Session Initiation Protocol (SIP)", RFC 4168,
October 2005.
Lingle, et al. Standards Track [Page 81]RFC 4780 SIP MIB Modules April 2007
Authors' Addresses
Kevin Lingle
Cisco Systems, Inc.
7025 Kit Creek Road
P.O. Box 14987
Research Triangle Park, NC 27709
US
Phone: +1 919 476 2029
EMail: klingle@cisco.com
Jean-Francois Mule
CableLabs
858 Coal Creek Circle
Louisville, CO 80027
US
Phone: +1 303 661 9100
EMail: jf.mule@cablelabs.com
Joon Maeng
5612 Sedona Drive
Austin, TX 78759
US
Phone: +1 512 418 0590
EMail: jmaeng@austin.rr.com
Dave Walker
EMail: drwalker@rogers.com
Lingle, et al. Standards Track [Page 82]
RFC 4780 SIP MIB Modules April 2007
Full Copyright Statement
Copyright (C) The IETF Trust (2007).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Lingle, et al. Standards Track [Page 83]
