Network Working Group H. Sjostrand
Request for Comments: 3295 ipUnplugged
Category: Standards Track J. Buerkle
Nortel Networks
B. Srinivasan
Cplane
June 2002
Definitions of Managed Objects for
the General Switch Management Protocol (GSMP)
Status of this Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2002). All Rights Reserved.
Abstract
This memo defines a portion of the Management Information Base (MIB)
for the use with the network management protocols in the Internet
community. In particular, it describes managed objects for the
General Switch Management Protocol (GSMP).
Table of Contents
1. Introduction............................................. 2
2. The SNMP Management Framework............................ 2
3. Structure of the MIB..................................... 3
3.1 Overview............................................. 3
3.2 Scope................................................ 4
3.3 MIB guideline........................................ 4
3.4 MIB groups........................................... 5
3.4.1 GSMP Switch Controller group................... 5
3.4.2 GSMP Switch group.............................. 6
3.4.3 GSMP Encapsulation groups...................... 6
3.4.4 GSMP General group............................. 7
3.4.5 The GSMP Notifications Group................... 7
3.5 Textual Conventions................................. 8
4. GSMP MIB Definitions.................................... 9
5. Acknowledgments......................................... 42
Sjostrand, et. al. Standards Track [Page 1]RFC 3295 GSMP MIB June 2002
6. References.............................................. 42
7. Intellectual Property Rights............................ 44
8. Security Considerations................................. 45
9. Authors' Addresses...................................... 46
10. Full Copyright Statement................................ 47
1. Introduction
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes managed objects for the General Switch
Management Protocol (GSMP).
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
2. The SNMP Management Framework
The SNMP Management Framework presently consists of five major
components:
* An overall architecture, described in RFC 2571 [RFC2571].
* Mechanisms for describing and naming objects and events for the
purpose of management. The first version of this Structure of
Management Information (SMI) is called SMIv1 and is described in
STD 16, RFC 1155 [RFC1155], STD 16, RFC 1212 [RFC1212], and RFC
1215 [RFC1215]. The second version, called SMIv2, is described in
STD 58, RFC 2578 [RFC2578], RFC 2579 [RFC2579], and RFC
2580[RFC2580].
* Message protocols for transferring management information. The
first version of the SNMP message protocol is called SNMPv1 and is
described in STD 15, RFC 1157 [RFC1157]. A second version of the
SNMP message protocol, which is not an Internet standards track
protocol, is called SNMPv2c and is described in RFC 1901 [RFC1901]
and RFC 1906 [RFC1906]. The third version of the message protocol
is called SNMPv3 and is described in RFC 1906 [RFC1906], RFC 2572
[RFC2572], and RFC 2574 [RFC2574].
* Protocol operations for accessing management information. The
first set of protocol operations and associated PDU formats are
described in STD 15, RFC 1157 [RFC1157]. A second set of
operations and associated PDU formats are described in 1905
[RFC1905].
Sjostrand, et. al. Standards Track [Page 2]RFC 3295 GSMP MIB June 2002
* A set of fundamental applications described in RFC 2573 [RFC2573],
and the view-based access control mechanism is described in RFC
2575 [RFC2575].
A more detailed introduction to the current SNMP Management Framework
can be found in RFC 2570 [RFC2570].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. Objects in the MIB are
defined using the mechanisms defined in the SMI.
This memo specifies a MIB module that is compliant to the SMIv2. A
MIB conforming to the SMIv1 can be produced through the appropriate
translations. The resulting translated MIB must be semantically
equivalent, except where objects or events are omitted because no
translation is possible (use of Counter64). Some machine readable
information in SMIv2 will be converted into textual descriptions in
SMIv1 during the translation process. However, this loss of machine
readable information is not considered to change the semantics of the
MIB.
3. Structure of the MIB
This memo defines a portion of the Management Information Base (MIB)
for the use with network management protocols in the Internet
community. In particular, it describes managed objects for the
General Switch Management Protocol (GSMP), as defined in [RFC3292].
3.1 Overview
The General Switch Management Protocol (GSMP) is a general purpose
protocol to control a label switch. GSMP allows a controller to
establish and release connections across the switch, to manage switch
ports and to request configuration information or statistics. It
also allows the switch to inform the controller of asynchronous
events such as a link going down.
The GSMP protocol is asymmetric, the controller being the master and
the switch being the slave. Multiple switches may be controlled by a
single controller using multiple instantiations of the protocol over
separate control connections. Also a switch may be controlled by
more than one controller by using the technique of partitioning.
Each instance of a (switch controller, switch partition) adjacency is
a session between one switch controller entity and one switch entity.
The MIB provides objects to configure/setup these entities to form
the GSMP sessions. It also provide objects to monitor these GSMP
sessions.
Sjostrand, et. al. Standards Track [Page 3]RFC 3295 GSMP MIB June 2002
3.2 Scope
The GSMP mib is a protocol mib. It contains objects to configure,
monitor, and maintain the GSMP protocol entity. It does not provide
any information learned via the protocol, such as "all ports config"
information.
The relationships between virtual entities, such as Virtual Switch
Entities, and "physical" entities, such as Switch Entities, falls
outside of the management of GSMP. This also applies for the
management of switch partitions. So this is excluded from the GSMP
mib.
It is possible to configure which, and how many Switch Controllers
are controlling one Switch since every potential session with the
switch has to be represented with an Switch entity. It is, however,
not possible to define that one Switch Controller shouldn't allow
other Switch controllers to control the same switch or partition on
the switch. It is assumed that there are mechanisms that synchronise
controllers and the configuration of them. This is outside the scope
of this mib.
3.3 MIB guideline
Two tables are used to configure potential GSMP sessions depending if
you are acting as a GSMP switch controller or a GSMP switch. Each
row in these tables initiates a GSMP session.
The entity ID is a 48-bit name that is unique within the operational
context of the device. A 48-bit IEEE 802 MAC address, if available,
MAY be used for the entity ID. If the Ethernet encapsulation is
used, the entity ID MUST be the IEEE 802 MAC address of the interface
on which the GSMP session is to be setup.
First, the encapsulation of the potential GSMP session shall be
defined. If ATM is used, a row in the gsmpAtmEncapTable has to be
created with the index set to the entity ID. The specified resources
should be allocated to GSMP. If TCP/IP is used, a row in the
gsmpTcpIpEncapTable has to be created with the index set to the
entity ID. The specified port shall be allocated to GSMP. No
special action is needed if ethernet encapsulation is used.
Then the entity information shall be defined. To create a Switch
Entity, an entry in the gsmpSwitchTable is created with the index set
to the entity ID. To create a Switch Controller Entity, an entry in
the gsmpControllerTable is created with the index set to the entity
ID.
Sjostrand, et. al. Standards Track [Page 4]
RFC 3295 GSMP MIB June 2002
When the row status of the GsmpControllerEntry or GsmpSwitchEntry is
set to active (e.g., in the case with ATM or TCP/IP there are active
rows with a corresponding entity ID), the adjacency protocol of GSMP
is started.
Another table, the gsmpSessionTable, shows the actual sessions that
are established or are in the process of being established. Each row
represents a specific session between an Entity and a peer. This
table carries information about the peer, the session, and parameters
that were negotiated by the adjacency procedures. The
gsmpSessionTable also contains statistical information regarding the
session.
This creation order SHOULD be used by all GSMP managers. This is to
avoid clash situations in multiple SNMP manager scenarios where
different managers may create competing entries in the different
tables.
Entities may very well be configured by other means than SNMP, e.g.,
the cli command. Such configured entities SHOULD be represented as
entries in the tables of this mib and SHOULD be possible to query,
and MAY be possible to alter with SNMP.
3.4 MIB groups
3.4.1 GSMP Switch Controller group
The controller group is used to configure a potential GSMP session on
a Switch Controller. A row in the gsmpControllerTable is created for
each such session. If ATM or TCP/IP encapsulation is used, a
corresponding row has to be created in these tables before the
session adjacency protocol is initiated.
If ATM or TCP/IP is used, encapsulation data is defined in the
corresponding encapsulation tables. If ethernet is used, the MAC
address of the interface defined for the session is set by the
Controller ID object.
The adjacency parameters are defined; such as
- Max supported GSMP version.
- Time between the periodic adjacency messages.
- Controller local port number and instance number.
- Whether partitions are being used and the partition ID for the
specific partitions this controller is concerned with if
partitions are used.
- The resynchronisation strategy for the session is specified.
Sjostrand, et. al. Standards Track [Page 5]RFC 3295 GSMP MIB June 2002
The notification mapping is set to specify for with events the
corresponding SNMP notifications are sent.
3.4.2 GSMP Switch group
The switch group is used to configure a potential GSMP session on a
Switch. A row in the gsmpSwitchTable is created for each such
session. If ATM or TCP/IP encapsulation is used, a corresponding row
has to be created in these tables before the session adjacency
protocol is initiated.
If ATM or TCP/IP is used, encapsulation data is defined in the
corresponding encapsulation tables. If ethernet is used the MAC
address of the interface defined for the session is set by the Switch
ID object.
The adjacency parameters are defined; such as
- Max supported GSMP version
- Time between the periodic adjacency messages
- Switch Name, local port number, and instance number.
- Whether partitions are being used and the partition ID for this
specific partition if partitions are used.
- The switch type could be set.
- The suggested maximum window size for unacknowledged request
messages.
Also, a notification mapping is set to specify for with events the
corresponding SNMP notifications are sent.
3.4.3 GSMP Encapsulation groups
The ATM Encapsulation Table and the TCP/IP Encapsulation Table
provides a way to configure information that are encapsulation
specific. The encapsulation data is further specified in [RFC3293].
If ATM encapsulation is used, the interface and the virtual channel
are specified.
If TCP/IP is used, the IP address and the port number are specified.
No special config data needed if Ethernet encapsulation is used.
This mib MAY be extended with new, standard or proprietary, GSMP
encapsulation types. If a new encapsulation type needs to be added,
it SHOULD be done in the form of a new table with the entity ID as an
index. A row in that encapsulation table SHOULD be created before
any row in a GSMP entity table is created that is using this new GSMP
encapsulation.
Sjostrand, et. al. Standards Track [Page 6]RFC 3295 GSMP MIB June 2002
3.4.4 GSMP General group
The GSMP session table provides a way to monitor and maintain GSMP
sessions.
The session is defined by a Switch Controller Entity and Switch
Entity pair.
3.4.5 The GSMP Notifications Group
The GSMP Notification Group defines notifications for GSMP entities.
These notifications provide a mechanism for a GSMP device to inform
the management station of status changes. Also a notification is
defined for each type of GSMP events.
The group of notifications consists of the following notifications:
- gsmpSessionDown
This notification is generated when a session is terminating and also
reports the final accounting statistics of the session.
- gsmpSessionUp
This notification is generated when a new session is established.
- gsmpSendFailureInd
This notification is generated when a message with a failure
indication was sent. This means that this notification identifies a
change to the gsmpSessionStatFailureInds object in a row of the
gsmpSessionTable.
- gsmpReceivedFailureInd
This notification is generated when a message with a failure
indication received. This means that this notification identifies a
change to the gsmpSessionStatReceivedFailures object in a row of the
gsmpSessionTable.
- gsmpPortUpEvent
This notification is generated when a Port Up Event is either
received or sent.
Sjostrand, et. al. Standards Track [Page 7]
RFC 3295 GSMP MIB June 2002
- gsmpPortDownEvent
This notification is generated when a Port Down Event is either
received or sent.
- gsmpInvalidLabelEvent
This notification is generated when an Invalid Label Event is either
received or sent.
- gsmpNewPortEvent
This notification is generated when New Port Event either is received
or sent.
- gsmpDeadPortEvent
This notification is generated when a Dead Port Event is either
received or sent.
- gsmpAdjacencyUpdateEvent
This notification is generated when an Adjacency Update Event is
either received or sent.
To disable or enable the sending of each notification, the bits in
the bitmap are set to 0 or 1 in the Notification mapping objects in
the Controller Entitiy or Switch Entity tables.
The GSMP notification map capability should not be seen as a
duplication of the filter mechanism in the snmp notification
originator application [RFC2573], but as a compliment, to configure
the relation between GSMP events and the SNMP notifications already
in the GSMP agent. SNMP notifications and GSMP events operate
sometimes on a different timescale, and it may in some applications
be devastating for a SNMP application to receive events for each GSMP
events. E.g. the invalid label event in a ATM switch scenario may
cause mass SNMP notification flooding if mapped to a SNMP
notification.
3.5 Textual Conventions
The datatypes GsmpNameType, GsmpLabelType, GsmpVersion,
GsmpPartitionType, and GsmpPartitionIdType are used as textual
conventions in this document. These textual conventions are used for
the convenience of humans reading the MIB. Objects defined using
these conventions are always encoded by means of the rules that
define their primitive type. However, the textual conventions have
Sjostrand, et. al. Standards Track [Page 8]
RFC 3295 GSMP MIB June 2002
special semantics associated with them. Hence, no changes to the SMI
or the SNMP are necessary to accommodate these textual conventions
which are adopted merely for the convenience of readers.
4. GSMP MIB Definitions
GSMP-MIB DEFINITIONS ::= BEGIN
IMPORTS
OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE,
Unsigned32, Integer32, mib-2
FROM SNMPv2-SMI -- [RFC2578]
RowStatus, TruthValue, TimeStamp,
StorageType, TEXTUAL-CONVENTION
FROM SNMPv2-TC -- [RFC2579]
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
FROM SNMPv2-CONF -- [RFC2580]
ZeroBasedCounter32
FROM RMON2-MIB -- [RFC2021]
InterfaceIndex
FROM IF-MIB -- [RFC2863]
AtmVcIdentifier, AtmVpIdentifier
FROM ATM-TC-MIB -- [RFC2514]
InetAddressType, InetAddress, InetPortNumber
FROM INET-ADDRESS-MIB ; -- [RFC3291]
gsmpMIB MODULE-IDENTITY
LAST-UPDATED "200205310000Z" -- May 31, 2002
ORGANIZATION "General Switch Management Protocol (gsmp)
Working Group, IETF"
CONTACT-INFO
"WG Charter:
http://www.ietf.org/html.charters/gsmp-charter.html
WG-email: gsmp@ietf.org
Subscribe: gsmp-request@ietf.org
Email Archive:
ftp://ftp.ietf.org/ietf-mail-archive/gsmp/
WG Chair: Avri Doria
Email: avri@acm.org
WG Chair: Kenneth Sundell
Email: ksundell@nortelnetworks.com
Editor: Hans Sjostrand
Email: hans@ipunplugged.com
Sjostrand, et. al. Standards Track [Page 9]RFC 3295 GSMP MIB June 2002
Editor: Joachim Buerkle
Email: joachim.buerkle@nortelnetworks.com
Editor: Balaji Srinivasan
Email: balaji@cplane.com"
DESCRIPTION
"This MIB contains managed object definitions for the
General Switch Management Protocol, GSMP, version 3"
REVISION "200205310000Z"
DESCRIPTION "Initial Version, published as RFC 3295"
::= { mib-2 98 }
gsmpNotifications OBJECT IDENTIFIER ::= { gsmpMIB 0 }
gsmpObjects OBJECT IDENTIFIER ::= { gsmpMIB 1 }
gsmpNotificationsObjects OBJECT IDENTIFIER ::= { gsmpMIB 2 }
gsmpConformance OBJECT IDENTIFIER ::= { gsmpMIB 3 }
--**************************************************************
-- GSMP Textual Conventions
--**************************************************************
GsmpNameType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The Name is a 48-bit quantity.
A 48-bit IEEE 802 MAC address, if
available, may be used."
SYNTAX OCTET STRING (SIZE(6))
GsmpPartitionType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Defining if partitions are used and how the partition id
is negotiated. "
SYNTAX INTEGER {
noPartition(1),
fixedPartitionRequest(2),
fixedPartitionAssigned(3)
}
GsmpPartitionIdType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A 8-bit quantity. The format of the Partition ID is not
defined in GSMP. If desired, the Partition ID can be
divided into multiple sub-identifiers within a single
Sjostrand, et. al. Standards Track [Page 10]RFC 3295 GSMP MIB June 2002
partition. For example: the Partition ID could be
subdivided into a 6-bit partition number and a 2-bit
sub-identifier which would allow a switch to support 64
partitions with 4 available IDs per partition."
SYNTAX OCTET STRING (SIZE(1))
GsmpVersion ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The version numbers defined for the GSMP protocol.
The version numbers used are defined in the
specifications of the respective protocol,
1 - GSMPv1.1 [RFC1987]
2 - GSMPv2.0 [RFC2397]
3 - GSMPv3 [RFC3292]
Other numbers may be defined for other versions
of the GSMP protocol."
SYNTAX Unsigned32
GsmpLabelType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The label is structured as a TLV, a tuple, consisting of
a Type, a Length, and a Value. The structure is defined
in [RFC 3292]. The label TLV is encoded as a 2 octet type
field, followed by a 2 octet Length field, followed by a
variable length Value field.
Additionally, a label field can be composed of many stacked
labels that together constitute the label."
SYNTAX OCTET STRING
--**************************************************************
-- GSMP Entity Objects
--**************************************************************
--
-- Switch Controller Entity table
--
gsmpControllerTable OBJECT-TYPE
SYNTAX SEQUENCE OF GsmpControllerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the Switch Controller
Entities. An entry in this table needs to be configured
(created) before a GSMP session might be started."
::= { gsmpObjects 1 }
Sjostrand, et. al. Standards Track [Page 11]RFC 3295 GSMP MIB June 2002
gsmpControllerEntry OBJECT-TYPE
SYNTAX GsmpControllerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the table showing
the data for a specific Switch Controller
Entity. If partitions are used, one entity
corresponds to one specific switch partition.
Depending of the encapsulation used,
a corresponding row in the gsmpAtmEncapTable or the
gsmpTcpIpEncapTable may have been created."
INDEX { gsmpControllerEntityId }
::= { gsmpControllerTable 1 }
GsmpControllerEntry ::= SEQUENCE {
gsmpControllerEntityId GsmpNameType,
gsmpControllerMaxVersion GsmpVersion,
gsmpControllerTimer Unsigned32,
gsmpControllerPort Unsigned32,
gsmpControllerInstance Unsigned32,
gsmpControllerPartitionType GsmpPartitionType,
gsmpControllerPartitionId GsmpPartitionIdType,
gsmpControllerDoResync TruthValue,
gsmpControllerNotificationMap BITS,
gsmpControllerSessionState INTEGER,
gsmpControllerStorageType StorageType,
gsmpControllerRowStatus RowStatus
}
gsmpControllerEntityId OBJECT-TYPE
SYNTAX GsmpNameType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Switch Controller Entity Id is unique
within the operational context of the device."
::= { gsmpControllerEntry 1 }
gsmpControllerMaxVersion OBJECT-TYPE
SYNTAX GsmpVersion
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The max version number of the GSMP protocol being used
in this session. The version is negotiated by the
adjacency protocol."
DEFVAL { 3 }
Sjostrand, et. al. Standards Track [Page 12]RFC 3295 GSMP MIB June 2002
::= { gsmpControllerEntry 2 }
gsmpControllerTimer OBJECT-TYPE
SYNTAX Unsigned32(1..255)
UNITS "100ms"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The timer specifies the nominal time between
periodic adjacency protocol messages. It is a constant
for the duration of a GSMP session. The timer is
specified in units of 100ms."
DEFVAL { 10 }
::= { gsmpControllerEntry 3 }
gsmpControllerPort OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The local port number for the Switch Controller
Entity."
REFERENCE
"General Switch Management Protocol V3: Section 3.1.2"
::= { gsmpControllerEntry 4 }
gsmpControllerInstance OBJECT-TYPE
SYNTAX Unsigned32(1..16777215)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The instance number for the Switch Controller
Entity. The Instance number is a 24-bit number
that should be guaranteed to be unique within
the recent past and to change when the link
or node comes back up after going down. Zero is
not a valid instance number. "
::= { gsmpControllerEntry 5 }
gsmpControllerPartitionType OBJECT-TYPE
SYNTAX GsmpPartitionType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A controller can request the specific partition identifier
to the session by setting the Partition Type to
fixedPartitionRequest(2). A controller can let the switch
decide whether it wants to assign a fixed partition ID or
Sjostrand, et. al. Standards Track [Page 13]RFC 3295 GSMP MIB June 2002
not, by setting the Partition Type to noPartition(1)."
::= { gsmpControllerEntry 6 }
gsmpControllerPartitionId OBJECT-TYPE
SYNTAX GsmpPartitionIdType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Id for the specific switch partition that this
Switch Controller is concerned with.
If partitions are not used or if the controller lets the
switch assigns Partition ID, i.e Partition Type =
noPartition(1), then this object is undefined."
::= { gsmpControllerEntry 7 }
gsmpControllerDoResync OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies whether the controller should
resynchronise or reset in case of loss of synchronisation.
If this object is set to true then the Controller should
resync with PFLAG=2 (recovered adjacency)."
DEFVAL { true }
::= { gsmpControllerEntry 8 }
gsmpControllerNotificationMap OBJECT-TYPE
SYNTAX BITS {
sessionDown(0),
sessionUp(1),
sendFailureIndication(2),
receivedFailureIndication(3),
portUpEvent(4),
portDownEvent(5),
invalidLabelEvent(6),
newPortEvent(7),
deadPortEvent(8),
adjacencyUpdateEvent(9)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This bitmap defines whether a corresponding SNMP
notification should be sent if a GSMP event is received
by the Switch Controller. If the bit is set to 1 a
notification should be sent. The handling and filtering of
the SNMP notifications are then further specified in the
Sjostrand, et. al. Standards Track [Page 14]RFC 3295 GSMP MIB June 2002
SNMP notification originator application. "
DEFVAL {{ sessionDown, sessionUp,
sendFailureIndication, receivedFailureIndication }}
::= { gsmpControllerEntry 9 }
gsmpControllerSessionState OBJECT-TYPE
SYNTAX INTEGER {
null(1),
synsent(2),
synrcvd(3),
estab(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state for the existing or potential session that
this entity is concerned with.
The NULL state is returned if the proper encapsulation
data is not yet configured, if the row is not in active
status or if the session is in NULL state as defined in
the GSMP specification."
::= { gsmpControllerEntry 10}
gsmpControllerStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this controller entity.
Conceptual rows having the value 'permanent' need not allow
write-access to any columnar objects in the row."
DEFVAL { nonVolatile }
::= { gsmpControllerEntry 11 }
gsmpControllerRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to
be created and deleted using the
RowStatus convention.
While the row is in active state it's not
possible to modify the value of any object
for that row except the gsmpControllerNotificationMap
and the gsmpControllerRowStatus objects."
::= { gsmpControllerEntry 12 }
Sjostrand, et. al. Standards Track [Page 15]RFC 3295 GSMP MIB June 2002
--
-- Switch Entity table
--
gsmpSwitchTable OBJECT-TYPE
SYNTAX SEQUENCE OF GsmpSwitchEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the Switch
Entities. An entry in this table needs to be configured
(created) before a GSMP session might be started."
::= { gsmpObjects 2 }
gsmpSwitchEntry OBJECT-TYPE
SYNTAX GsmpSwitchEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the table showing
the data for a specific Switch
Entity. If partitions are used, one entity
corresponds to one specific switch partition.
Depending of the encapsulation used,
a corresponding row in the gsmpAtmEncapTable or the
gsmpTcpIpEncapTable may have been created."
INDEX { gsmpSwitchEntityId }
::= { gsmpSwitchTable 1 }
GsmpSwitchEntry ::= SEQUENCE {
gsmpSwitchEntityId GsmpNameType,
gsmpSwitchMaxVersion GsmpVersion,
gsmpSwitchTimer Unsigned32,
gsmpSwitchName GsmpNameType,
gsmpSwitchPort Unsigned32,
gsmpSwitchInstance Unsigned32,
gsmpSwitchPartitionType GsmpPartitionType,
gsmpSwitchPartitionId GsmpPartitionIdType,
gsmpSwitchNotificationMap BITS,
gsmpSwitchSwitchType OCTET STRING,
gsmpSwitchWindowSize Unsigned32,
gsmpSwitchSessionState INTEGER,
gsmpSwitchStorageType StorageType,
gsmpSwitchRowStatus RowStatus
}
gsmpSwitchEntityId OBJECT-TYPE
SYNTAX GsmpNameType
Sjostrand, et. al. Standards Track [Page 16]RFC 3295 GSMP MIB June 2002
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Switch Entity Id is unique
within the operational context of the device. "
::= { gsmpSwitchEntry 1 }
gsmpSwitchMaxVersion OBJECT-TYPE
SYNTAX GsmpVersion
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The max version number of the GSMP protocol being
supported by this Switch. The version is negotiated by
the adjacency protocol."
DEFVAL { 3 }
::= { gsmpSwitchEntry 2 }
gsmpSwitchTimer OBJECT-TYPE
SYNTAX Unsigned32(1..255)
UNITS "100ms"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The timer specifies the nominal time between
periodic adjacency protocol messages. It is a constant
for the duration of a GSMP session. The timer is
specified in units of 100ms."
DEFVAL { 10 }
::= { gsmpSwitchEntry 3 }
gsmpSwitchName OBJECT-TYPE
SYNTAX GsmpNameType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The name of the Switch. The first three octets must be an
Organisationally Unique Identifier (OUI) that identifies
the manufacturer of the Switch. This is by default set to
the same value as the gsmpSwitchId object if not
separately specified. "
::= {gsmpSwitchEntry 4 }
gsmpSwitchPort OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
Sjostrand, et. al. Standards Track [Page 17]RFC 3295 GSMP MIB June 2002
"The local port number for this Switch Entity."
REFERENCE
"General Switch Management Protocol V3: Section 3.1.2"
::= { gsmpSwitchEntry 5 }
gsmpSwitchInstance OBJECT-TYPE
SYNTAX Unsigned32(1..16777215)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The instance number for the Switch Entity.
The Instance number is a 24-bit number
that should be guaranteed to be unique within
the recent past and to change when the link
or node comes back up after going down. Zero is
not a valid instance number."
::= { gsmpSwitchEntry 6 }
gsmpSwitchPartitionType OBJECT-TYPE
SYNTAX GsmpPartitionType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A switch can assign the specific partition identifier to
the session by setting the Partition Type to
fixedPartitionAssigned(3). A switch can specify
that no partitions are handled in the session by setting
the Partition Type to noPartition(1)."
::= { gsmpSwitchEntry 7 }
gsmpSwitchPartitionId OBJECT-TYPE
SYNTAX GsmpPartitionIdType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Id for this specific switch partition that the switch
entity represents. If partitions are not used, i.e.
Partition Type = noPartition(1), then this object is
undefined."
::= { gsmpSwitchEntry 8 }
gsmpSwitchNotificationMap OBJECT-TYPE
SYNTAX BITS {
sessionDown(0),
sessionUp(1),
sendFailureIndication(2),
receivedFailureIndication(3),
portUpEvent(4),
Sjostrand, et. al. Standards Track [Page 18]RFC 3295 GSMP MIB June 2002
portDownEvent(5),
invalidLabelEvent(6),
newPortEvent(7),
deadPortEvent(8),
adjacencyUpdateEvent(9)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This bitmap defines whether a corresponding SNMP
notification should be sent if an GSMP event is sent
by the Switch Entity. If the bit is set to 1 a
notification should be sent. The handling and filtering of
the SNMP notifications are then further specified in the
SNMP notification originator application. "
DEFVAL {{ sessionDown, sessionUp,
sendFailureIndication, receivedFailureIndication }}
::= { gsmpSwitchEntry 9 }
gsmpSwitchSwitchType OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(2))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A 16-bit field allocated by the manufacturer
of the switch. The Switch Type
identifies the product. When the Switch Type is combined
with the OUI from the Switch Name the product is
uniquely identified. "
::= { gsmpSwitchEntry 10 }
gsmpSwitchWindowSize OBJECT-TYPE
SYNTAX Unsigned32(1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of unacknowledged request messages
that may be transmitted by the controller without the
possibility of loss. This field is used to prevent
request messages from being lost in the switch because of
overflow in the receive buffer. The field is a hint to
the controller."
::= { gsmpSwitchEntry 11 }
gsmpSwitchSessionState OBJECT-TYPE
SYNTAX INTEGER {
null(1),
synsent(2),
Sjostrand, et. al. Standards Track [Page 19]RFC 3295 GSMP MIB June 2002
synrcvd(3),
estab(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state for the existing or potential session that
this entity is concerned with.
The NULL state is returned if the proper encapsulation
data is not yet configured, if the row is not in active
status or if the session is in NULL state as defined in
the GSMP specification."
::= { gsmpSwitchEntry 12}
gsmpSwitchStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this switch entity.
Conceptual rows having the value 'permanent' need not allow
write-access to any columnar objects in the row."
DEFVAL { nonVolatile }
::= { gsmpSwitchEntry 13 }
gsmpSwitchRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to
be created and deleted using the
RowStatus convention.
While the row is in active state it's not
possible to modify the value of any object
for that row except the gsmpSwitchNotificationMap
and the gsmpSwitchRowStatus objects."
::= { gsmpSwitchEntry 14 }
--**************************************************************
-- GSMP Encapsulation Objects
--**************************************************************
--
-- GSMP ATM Encapsulation Table
--
gsmpAtmEncapTable OBJECT-TYPE
Sjostrand, et. al. Standards Track [Page 20]RFC 3295 GSMP MIB June 2002
SYNTAX SEQUENCE OF GsmpAtmEncapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the atm encapsulation data
for the Controller or Switch that uses atm aal5 as
encapsulation. "
::= { gsmpObjects 3 }
gsmpAtmEncapEntry OBJECT-TYPE
SYNTAX GsmpAtmEncapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the table showing
the encapsulation data for a specific
Switch Controller entity or Switch entity."
INDEX { gsmpAtmEncapEntityId }
::= { gsmpAtmEncapTable 1 }
GsmpAtmEncapEntry ::= SEQUENCE {
gsmpAtmEncapEntityId GsmpNameType,
gsmpAtmEncapIfIndex InterfaceIndex,
gsmpAtmEncapVpi AtmVpIdentifier,
gsmpAtmEncapVci AtmVcIdentifier,
gsmpAtmEncapStorageType StorageType,
gsmpAtmEncapRowStatus RowStatus
}
gsmpAtmEncapEntityId OBJECT-TYPE
SYNTAX GsmpNameType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Controller Id or Switch Id that is unique
within the operational context of the device. "
::= { gsmpAtmEncapEntry 1 }
gsmpAtmEncapIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The interface index for the virtual channel over which
the GSMP session is established, i.e., the GSMP control
channel for LLC/SNAP encapsulated GSMP messages on an
ATM data link layer."
::= { gsmpAtmEncapEntry 2 }
Sjostrand, et. al. Standards Track [Page 21]RFC 3295 GSMP MIB June 2002
gsmpAtmEncapVpi OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" The VPI value for the virtual channel over which the
GSMP session is established, i.e., the GSMP control
channel for LLC/SNAP encapsulated GSMP messages on an
ATM data link layer."
DEFVAL { 0 }
::= { gsmpAtmEncapEntry 3 }
gsmpAtmEncapVci OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" The VCI value for the virtual channel over which the
GSMP session is established, i.e., the GSMP control
channel for LLC/SNAP encapsulated GSMP messages on an
ATM data link layer."
DEFVAL { 15 }
::= { gsmpAtmEncapEntry 4 }
gsmpAtmEncapStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this entry. It should have the same
value as the StorageType in the referring Switch
Controller entity or Switch entity."
DEFVAL { nonVolatile }
::= { gsmpAtmEncapEntry 5 }
gsmpAtmEncapRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to
be created and deleted using the
RowStatus convention.
While the row is in active state it's not
possible to modify the value of any object
for that row except the gsmpAtmEncapRowStatus object."
::= { gsmpAtmEncapEntry 6 }
Sjostrand, et. al. Standards Track [Page 22]RFC 3295 GSMP MIB June 2002
--
-- GSMP TCP/IP Encapsulation Table
--
gsmpTcpIpEncapTable OBJECT-TYPE
SYNTAX SEQUENCE OF GsmpTcpIpEncapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the encapsulation data
for the Controller or Switch that uses TCP/IP as
encapsulation."
::= { gsmpObjects 4 }
gsmpTcpIpEncapEntry OBJECT-TYPE
SYNTAX GsmpTcpIpEncapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the table showing
the encapsulation data for a specific
Switch Controller entity or Switch entity."
INDEX { gsmpTcpIpEncapEntityId }
::= { gsmpTcpIpEncapTable 1 }
GsmpTcpIpEncapEntry ::= SEQUENCE {
gsmpTcpIpEncapEntityId GsmpNameType,
gsmpTcpIpEncapAddressType InetAddressType,
gsmpTcpIpEncapAddress InetAddress,
gsmpTcpIpEncapPortNumber InetPortNumber,
gsmpTcpIpEncapStorageType StorageType,
gsmpTcpIpEncapRowStatus RowStatus
}
gsmpTcpIpEncapEntityId OBJECT-TYPE
SYNTAX GsmpNameType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Controller or Switch Id is unique
within the operational context of the device. "
::= { gsmpTcpIpEncapEntry 1 }
gsmpTcpIpEncapAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
Sjostrand, et. al. Standards Track [Page 23]RFC 3295 GSMP MIB June 2002
"The type of address in gsmpTcpIpEncapAddress."
::= { gsmpTcpIpEncapEntry 2 }
gsmpTcpIpEncapAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The IPv4 or IPv6 address used for
the GSMP session peer."
::= { gsmpTcpIpEncapEntry 3 }
gsmpTcpIpEncapPortNumber OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The TCP port number used for the TCP session
establishment to the GSMP peer."
DEFVAL { 6068 }
::= { gsmpTcpIpEncapEntry 4 }
gsmpTcpIpEncapStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this entry. It should have the same
value as the StorageType in the referring Switch
Controller entity or Switch entity."
DEFVAL { nonVolatile }
::= { gsmpTcpIpEncapEntry 5 }
gsmpTcpIpEncapRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to
be created and deleted using the
RowStatus convention.
While the row is in active state it's not
possible to modify the value of any object
for that row except the gsmpTcpIpEncapRowStatus object."
::= { gsmpTcpIpEncapEntry 6 }
--**************************************************************
-- GSMP Session Objects
Sjostrand, et. al. Standards Track [Page 24]RFC 3295 GSMP MIB June 2002
--**************************************************************
--
-- GSMP Session table
--
gsmpSessionTable OBJECT-TYPE
SYNTAX SEQUENCE OF GsmpSessionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the sessions between
Controller and Switch pairs. "
::= { gsmpObjects 5 }
gsmpSessionEntry OBJECT-TYPE
SYNTAX GsmpSessionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the table showing
the session data for a specific Controller and
Switch pair. Also, statistics for this specific
session is shown."
INDEX { gsmpSessionThisSideId, gsmpSessionFarSideId }
::= { gsmpSessionTable 1 }
GsmpSessionEntry ::= SEQUENCE {
gsmpSessionThisSideId GsmpNameType,
gsmpSessionFarSideId GsmpNameType,
gsmpSessionVersion GsmpVersion,
gsmpSessionTimer Integer32,
gsmpSessionPartitionId GsmpPartitionIdType,
gsmpSessionAdjacencyCount Unsigned32,
gsmpSessionFarSideName GsmpNameType,
gsmpSessionFarSidePort Unsigned32,
gsmpSessionFarSideInstance Unsigned32,
gsmpSessionLastFailureCode Unsigned32,
gsmpSessionDiscontinuityTime TimeStamp,
gsmpSessionStartUptime TimeStamp,
gsmpSessionStatSentMessages ZeroBasedCounter32,
gsmpSessionStatFailureInds ZeroBasedCounter32,
gsmpSessionStatReceivedMessages ZeroBasedCounter32,
gsmpSessionStatReceivedFailures ZeroBasedCounter32,
gsmpSessionStatPortUpEvents ZeroBasedCounter32,
gsmpSessionStatPortDownEvents ZeroBasedCounter32,
gsmpSessionStatInvLabelEvents ZeroBasedCounter32,
gsmpSessionStatNewPortEvents ZeroBasedCounter32,
Sjostrand, et. al. Standards Track [Page 25]RFC 3295 GSMP MIB June 2002
gsmpSessionStatDeadPortEvents ZeroBasedCounter32,
gsmpSessionStatAdjUpdateEvents ZeroBasedCounter32
}
gsmpSessionThisSideId OBJECT-TYPE
SYNTAX GsmpNameType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This side ID uniquely identifies the entity that this
session relates to within the operational
context of the device. "
::= { gsmpSessionEntry 1 }
gsmpSessionFarSideId OBJECT-TYPE
SYNTAX GsmpNameType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Far side ID uniquely identifies the entity that this
session is established against. "
::= { gsmpSessionEntry 2 }
gsmpSessionVersion OBJECT-TYPE
SYNTAX GsmpVersion
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The version number of the GSMP protocol being used in
this session. The version is the result of the
negotiation by the adjacency protocol."
::= { gsmpSessionEntry 3 }
gsmpSessionTimer OBJECT-TYPE
SYNTAX Integer32
UNITS "100ms"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The timer specifies the time remaining until the
adjacency timer expires. The object could take negative
values since if no valid GSMP messages are
received in any period of time in excess of three times
the value of the Timer negotiated by the adjacency
protocol loss of synchronisation may be declared. The
timer is specified in units of 100ms."
::= { gsmpSessionEntry 4 }
Sjostrand, et. al. Standards Track [Page 26]RFC 3295 GSMP MIB June 2002
gsmpSessionPartitionId OBJECT-TYPE
SYNTAX GsmpPartitionIdType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Partition Id for the specific switch partition that
this session is concerned with."
::= { gsmpSessionEntry 5 }
gsmpSessionAdjacencyCount OBJECT-TYPE
SYNTAX Unsigned32(1..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current number of adjacencies
that are established with controllers and the switch
partition that is used for this session. The value
includes this session."
::= { gsmpSessionEntry 6 }
gsmpSessionFarSideName OBJECT-TYPE
SYNTAX GsmpNameType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The name of the far side as advertised in the adjacency
message."
::= {gsmpSessionEntry 7}
gsmpSessionFarSidePort OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The local port number of the link across which the
message is being sent."
REFERENCE
"General Switch Management Protocol V3: Section 3.1.2"
::= { gsmpSessionEntry 8 }
gsmpSessionFarSideInstance OBJECT-TYPE
SYNTAX Unsigned32(1..16777215)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The instance number used for the link during this
session. The Instance number is a 24-bit number
that should be guaranteed to be unique within
Sjostrand, et. al. Standards Track [Page 27]RFC 3295 GSMP MIB June 2002
the recent past and to change when the link
or node comes back up after going down. Zero is not
a valid instance number."
::= { gsmpSessionEntry 9 }
gsmpSessionLastFailureCode OBJECT-TYPE
SYNTAX Unsigned32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This is the last failure code that was received over
this session. If no failure code have been received, the
value is zero."
::= { gsmpSessionEntry 10 }
gsmpSessionDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion at
which one or more of this session's counters
suffered a discontinuity. If no such discontinuities have
occurred since then, this object contains the same
timestamp as gsmpSessionStartUptime ."
::= { gsmpSessionEntry 11 }
gsmpSessionStartUptime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The value of sysUpTime when the session came to
established state."
::= { gsmpSessionEntry 12 }
gsmpSessionStatSentMessages OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of messages that have been sent in this
session. All GSMP messages pertaining to this session after
the session came to established state SHALL
be counted, also including adjacency protocol messages
and failure response messages.
When the counter suffers any discontinuity, then
the gsmpSessionDiscontinuityTime object indicates when it
Sjostrand, et. al. Standards Track [Page 28]RFC 3295 GSMP MIB June 2002
happened."
::= { gsmpSessionEntry 13 }
gsmpSessionStatFailureInds OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of messages that have been sent with a
failure indication in this session. Warning messages
SHALL NOT be counted.
When the counter suffers any discontinuity, then
the gsmpSessionDiscontinuityTime object indicates when it
happened."
REFERENCE
"General Switch Management Protocol V3: Section 12.1"
::= { gsmpSessionEntry 14 }
gsmpSessionStatReceivedMessages OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of messages that have been received in
this session. All legal GSMP messages pertaining to this
session after the session came to established state SHALL
be counted, also including adjacency protocol messages
and failure response messages.
When the counter suffers any discontinuity, then
the gsmpSessionDiscontinuityTime object indicates when it
happened."
::= { gsmpSessionEntry 15 }
gsmpSessionStatReceivedFailures OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of messages that have been received in
this session with a failure indication. Warning messages
SHALL NOT be counted.
When the counter suffers any discontinuity, then
the gsmpSessionDiscontinuityTime object indicates when it
happened."
REFERENCE
"General Switch Management Protocol V3: Section 12.1"
::= { gsmpSessionEntry 16 }
Sjostrand, et. al. Standards Track [Page 29]RFC 3295 GSMP MIB June 2002
gsmpSessionStatPortUpEvents OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Port Up events that have been sent or
received on this session.
When the counter suffers any discontinuity, then
the gsmpSessionDiscontinuityTime object indicates when it
happened."
REFERENCE
"General Switch Management Protocol V3: Section 9.1"
::= { gsmpSessionEntry 17 }
gsmpSessionStatPortDownEvents OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Port Down events that have been sent or
received on this session.
When the counter suffers any discontinuity, then
the gsmpSessionDiscontinuityTime object indicates when it
happened."
REFERENCE
"General Switch Management Protocol V3: Section 9.2"
::= { gsmpSessionEntry 18 }
gsmpSessionStatInvLabelEvents OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Invalid label events that have been sent
or received on this session.
When the counter suffers any discontinuity, then
the gsmpSessionDiscontinuityTime object indicates when it
happened."
REFERENCE
"General Switch Management Protocol V3: Section 9.3"
::= { gsmpSessionEntry 19 }
gsmpSessionStatNewPortEvents OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of New Port events that have been sent or
Sjostrand, et. al. Standards Track [Page 30]RFC 3295 GSMP MIB June 2002
received on this session.
When the counter suffers any discontinuity, then
the gsmpSessionDiscontinuityTime object indicates when it
happened."
REFERENCE
"General Switch Management Protocol V3: Section 9.4"
::= { gsmpSessionEntry 20 }
gsmpSessionStatDeadPortEvents OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Dead Port events that have been sent or
received on this session.
When the counter suffers any discontinuity, then
the gsmpSessionDiscontinuityTime object indicates when it
happened."
REFERENCE
"General Switch Management Protocol V3: Section 9.5"
::= { gsmpSessionEntry 21 }
gsmpSessionStatAdjUpdateEvents OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Adjacency Update events that have been sent
or received on this session.
When the counter suffers any discontinuity, then
the gsmpSessionDiscontinuityTime object indicates when it
happened."
REFERENCE
"General Switch Management Protocol V3: Section 9.6"
::= { gsmpSessionEntry 22 }
-- **************************************************************
-- GSMP Notifications
-- **************************************************************
--
-- Notification objects
--
gsmpEventPort OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS accessible-for-notify
Sjostrand, et. al. Standards Track [Page 31]RFC 3295 GSMP MIB June 2002
STATUS current
DESCRIPTION
"This object specifies the Port Number that is
carried in this event."
::= { gsmpNotificationsObjects 1 }
gsmpEventPortSessionNumber OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object specifies the Port Session Number that is
carried in this event."
::= { gsmpNotificationsObjects 2 }
gsmpEventSequenceNumber OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object specifies the Event Sequence Number that is
carried in this event."
::= { gsmpNotificationsObjects 3 }
gsmpEventLabel OBJECT-TYPE
SYNTAX GsmpLabelType
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object specifies the Label that is
carried in this event."
::= { gsmpNotificationsObjects 4 }
--
-- Notifications
--
gsmpSessionDown NOTIFICATION-TYPE
OBJECTS {
gsmpSessionStartUptime,
gsmpSessionStatSentMessages,
gsmpSessionStatFailureInds,
gsmpSessionStatReceivedMessages,
gsmpSessionStatReceivedFailures,
gsmpSessionStatPortUpEvents,
gsmpSessionStatPortDownEvents,
gsmpSessionStatInvLabelEvents,
Sjostrand, et. al. Standards Track [Page 32]RFC 3295 GSMP MIB June 2002
gsmpSessionStatNewPortEvents,
gsmpSessionStatDeadPortEvents,
gsmpSessionStatAdjUpdateEvents
}
STATUS current
DESCRIPTION
"When it has been enabled, this notification is
generated whenever a session is taken down, regardless
of whether the session went down normally or not.
Its purpose is to allow a management application
(primarily an accounting application) that is
monitoring the session statistics to receive the final
values of these counters, so that the application can
properly account for the amounts the counters were
incremented since the last time the application polled
them. The gsmpSessionStartUptime object provides the
total amount of time that the session was active.
This notification is not a substitute for polling the
session statistic counts. In particular, the count
values reported in this notification cannot be assumed
to be the complete totals for the life of the session,
since they may have wrapped while the
session was up.
The session to which this notification
applies is identified by the gsmpSessionThisSideId and
gsmpSessionFarSideId which could be inferred from the
Object Identifiers of the objects contained in the
notification.
An instance of this notification will contain exactly
one instance of each of its objects, and these objects
will all belong to the same conceptual row of the
gsmpSessionTable."
::= { gsmpNotifications 1 }
gsmpSessionUp NOTIFICATION-TYPE
OBJECTS {
gsmpSessionFarSideInstance
}
STATUS current
DESCRIPTION
"When it has been enabled, this notification is
generated when new session is established.
The new session is identified by the gsmpSessionThisSideId
and gsmpSessionFarSideId which could be inferred from the
Object Identifier of the gsmpSessionFarSideInstance object
Sjostrand, et. al. Standards Track [Page 33]RFC 3295 GSMP MIB June 2002
contained in the notification."
::= { gsmpNotifications 2 }
gsmpSentFailureInd NOTIFICATION-TYPE
OBJECTS {
gsmpSessionLastFailureCode,
gsmpSessionStatFailureInds
}
STATUS current
DESCRIPTION
"When it has been enabled, this notification is
generated when a message with a failure indication was
sent.
The notification indicates a change in the value of
gsmpSessionStatFailureInds. The
gsmpSessionLastFailureCode contains the failure
reason.
The session to which this notification
applies is identified by the gsmpSessionThisSideId and
gsmpSessionFarSideId which could be inferred from the
Object Identifiers of the objects contained in the
notification."
::= { gsmpNotifications 3 }
gsmpReceivedFailureInd NOTIFICATION-TYPE
OBJECTS {
gsmpSessionLastFailureCode,
gsmpSessionStatReceivedFailures
}
STATUS current
DESCRIPTION
"When it has been enabled, this notification is
generate when a message with a failure indication
is received.
The notification indicates a change in the value of
gsmpSessionStatReceivedFailures. The
gsmpSessionLastFailureCode contains the failure
reason.
The session to which this notification
applies is identified by the gsmpSessionThisSideId and
gsmpSessionFarSideId which could be inferred from the
Object Identifiers of the objects contained in the
notification."
::= { gsmpNotifications 4 }
Sjostrand, et. al. Standards Track [Page 34]RFC 3295 GSMP MIB June 2002
gsmpPortUpEvent NOTIFICATION-TYPE
OBJECTS {
gsmpSessionStatPortUpEvents,
gsmpEventPort,
gsmpEventPortSessionNumber,
gsmpEventSequenceNumber
}
STATUS current
DESCRIPTION
"When it has been enabled, this notification is
generated when a Port Up Event occurs.
The notification indicates a change in the value of
gsmpSessionStatPortUpEvents.
The session to which this notification
applies is identified by the gsmpSessionThisSideId and
gsmpSessionFarSideId which could be inferred from the
Object Identifier of the gsmpSessionStatPortUpEvents
object contained in the notification."
::= { gsmpNotifications 5 }
gsmpPortDownEvent NOTIFICATION-TYPE
OBJECTS {
gsmpSessionStatPortDownEvents,
gsmpEventPort,
gsmpEventPortSessionNumber,
gsmpEventSequenceNumber
}
STATUS current
DESCRIPTION
"When it has been enabled, this notification is
generated when a Port Down Event occurs.
The notification indicates a change in the value of
gsmpSessionStatPortDownEvents.
The session to which this notification
applies is identified by the gsmpSessionThisSideId and
gsmpSessionFarSideId which could be inferred from the
Object Identifier of the gsmpSessionStatPortDownEvents
object contained in the notification."
::= { gsmpNotifications 6 }
gsmpInvalidLabelEvent NOTIFICATION-TYPE
OBJECTS {
gsmpSessionStatInvLabelEvents,
gsmpEventPort,
Sjostrand, et. al. Standards Track [Page 35]RFC 3295 GSMP MIB June 2002
gsmpEventLabel,
gsmpEventSequenceNumber
}
STATUS current
DESCRIPTION
"When it has been enabled, this notification is
generated when an Invalid Label Event occurs.
The notification indicates a change in the value of
gsmpSessionStatInvLabelEvents.
The session to which this notification
applies is identified by the gsmpSessionThisSideId and
gsmpSessionFarSideId which could be inferred from the
Object Identifier of the gsmpSessionStatInvLabelEvents
object contained in the notification."
::= { gsmpNotifications 7 }
gsmpNewPortEvent NOTIFICATION-TYPE
OBJECTS {
gsmpSessionStatNewPortEvents,
gsmpEventPort,
gsmpEventPortSessionNumber,
gsmpEventSequenceNumber
}
STATUS current
DESCRIPTION
"When it has been enabled, this notification is
generated when a New Port Event occurs.
The notification indicates a change in the value of
gsmpSessionStatNewPortEvents.
The session to which this notification
applies is identified by the gsmpSessionThisSideId and
gsmpSessionFarSideId which could be inferred from the
Object Identifier of the gsmpSessionStatNewPortEvents
object contained in the notification."
::= { gsmpNotifications 8 }
gsmpDeadPortEvent NOTIFICATION-TYPE
OBJECTS {
gsmpSessionStatDeadPortEvents,
gsmpEventPort,
gsmpEventPortSessionNumber,
gsmpEventSequenceNumber
}
STATUS current
Sjostrand, et. al. Standards Track [Page 36]RFC 3295 GSMP MIB June 2002
DESCRIPTION
"When it has been enabled, this notification is
generated when a Dead Port Event occurs.
The notification indicates a change in the value of
gsmpSessionStatDeadPortEvents.
The session to which this notification
applies is identified by the gsmpSessionThisSideId and
gsmpSessionFarSideId which could be inferred from the
Object Identifier of the gsmpSessionStatDeadPortEvents
object contained in the notification."
::= { gsmpNotifications 9 }
gsmpAdjacencyUpdateEvent NOTIFICATION-TYPE
OBJECTS {
gsmpSessionAdjacencyCount,
gsmpSessionStatAdjUpdateEvents,
gsmpEventSequenceNumber
}
STATUS current
DESCRIPTION
"When it has been enabled, this notification is
generated when an Adjacency Update Event occurs.
The gsmpSessionAdjacencyCount contains the new value of
the number of adjacencies
that are established with controllers and the switch
partition that is used for this session.
The notification indicates a change in the value of
gsmpSessionStatAdjUpdateEvents.
The session to which this notification
applies is identified by the gsmpSessionThisSideId and
gsmpSessionFarSideId which could be inferred from the
Object Identifier of the gsmpSessionAdjacencyCount
or the gsmpSessionStatAdjUpdateEvents object contained
in the notification."
::= { gsmpNotifications 10 }
Sjostrand, et. al. Standards Track [Page 37]RFC 3295 GSMP MIB June 2002
--**************************************************************
-- GSMP Compliance
--**************************************************************
gsmpGroups OBJECT IDENTIFIER ::= { gsmpConformance 1 }
gsmpCompliances OBJECT IDENTIFIER ::= { gsmpConformance 2 }
gsmpModuleCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for agents that support
the GSMP MIB."
MODULE -- this module
MANDATORY-GROUPS { gsmpGeneralGroup
}
GROUP gsmpControllerGroup
DESCRIPTION
"This group is mandatory for all Switch
Controllers"
GROUP gsmpSwitchGroup
DESCRIPTION
"This group is mandatory for all Switches"
GROUP gsmpAtmEncapGroup
DESCRIPTION
"This group must be supported if ATM is used for GSMP
encapsulation. "
GROUP gsmpTcpIpEncapGroup
DESCRIPTION
"This group must be supported if TCP/IP is used for GSMP
encapsulation. "
OBJECT gsmpTcpIpEncapAddressType
SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2),
ipv4z(3), ipv6z(4) }
DESCRIPTION
"An implementation is only required to support
'unknown(0)', and IPv4 addresses. Supporting addresses with
zone index or IPv6 addresses are optional. Defining
Internet addresses by using DNS domain names are not
allowed."
OBJECT gsmpTcpIpEncapAddress
SYNTAX InetAddress (SIZE(0|4|8|16|20))
DESCRIPTION
"An implementation is only required to support
Sjostrand, et. al. Standards Track [Page 38]RFC 3295 GSMP MIB June 2002
IPv4 addresses. Supporting addresses with zone index or IPv6
addresses are optional."
GROUP gsmpNotificationObjectsGroup
DESCRIPTION
"This group must be supported if notifications
are supported. "
GROUP gsmpNotificationsGroup
DESCRIPTION
"This group must be supported if notifications
are supported. "
::= { gsmpCompliances 1 }
-- units of conformance
gsmpGeneralGroup OBJECT-GROUP
OBJECTS {
gsmpSessionVersion,
gsmpSessionTimer,
gsmpSessionPartitionId,
gsmpSessionAdjacencyCount,
gsmpSessionFarSideName,
gsmpSessionFarSidePort,
gsmpSessionFarSideInstance,
gsmpSessionLastFailureCode,
gsmpSessionDiscontinuityTime,
gsmpSessionStartUptime,
gsmpSessionStatSentMessages,
gsmpSessionStatFailureInds,
gsmpSessionStatReceivedMessages,
gsmpSessionStatReceivedFailures,
gsmpSessionStatPortUpEvents,
gsmpSessionStatPortDownEvents,
gsmpSessionStatInvLabelEvents,
gsmpSessionStatNewPortEvents,
gsmpSessionStatDeadPortEvents,
gsmpSessionStatAdjUpdateEvents
}
STATUS current
DESCRIPTION
"Objects that apply to all GSMP implementations."
::= { gsmpGroups 1 }
gsmpControllerGroup OBJECT-GROUP
OBJECTS {
gsmpControllerMaxVersion,
Sjostrand, et. al. Standards Track [Page 39]RFC 3295 GSMP MIB June 2002
gsmpControllerTimer,
gsmpControllerPort,
gsmpControllerInstance,
gsmpControllerPartitionType,
gsmpControllerPartitionId,
gsmpControllerDoResync,
gsmpControllerNotificationMap,
gsmpControllerSessionState,
gsmpControllerStorageType,
gsmpControllerRowStatus
}
STATUS current
DESCRIPTION
"Objects that apply GSMP implementations of
Switch Controllers."
::= { gsmpGroups 2 }
gsmpSwitchGroup OBJECT-GROUP
OBJECTS {
gsmpSwitchMaxVersion,
gsmpSwitchTimer,
gsmpSwitchName,
gsmpSwitchPort,
gsmpSwitchInstance,
gsmpSwitchPartitionType,
gsmpSwitchPartitionId,
gsmpSwitchNotificationMap,
gsmpSwitchSwitchType,
gsmpSwitchWindowSize,
gsmpSwitchSessionState,
gsmpSwitchStorageType,
gsmpSwitchRowStatus
}
STATUS current
DESCRIPTION
"Objects that apply GSMP implementations of
Switches."
::= { gsmpGroups 3 }
gsmpAtmEncapGroup OBJECT-GROUP
OBJECTS {
gsmpAtmEncapIfIndex,
gsmpAtmEncapVpi,
gsmpAtmEncapVci,
gsmpAtmEncapStorageType,
gsmpAtmEncapRowStatus
}
STATUS current
Sjostrand, et. al. Standards Track [Page 40]RFC 3295 GSMP MIB June 2002
DESCRIPTION
"Objects that apply to GSMP implementations that
supports ATM for GSMP encapsulation."
::= { gsmpGroups 4 }
gsmpTcpIpEncapGroup OBJECT-GROUP
OBJECTS {
gsmpTcpIpEncapAddressType,
gsmpTcpIpEncapAddress,
gsmpTcpIpEncapPortNumber,
gsmpTcpIpEncapStorageType,
gsmpTcpIpEncapRowStatus
}
STATUS current
DESCRIPTION
"Objects that apply to GSMP implementations that
supports TCP/IP for GSMP encapsulation."
::= { gsmpGroups 5 }
gsmpNotificationObjectsGroup OBJECT-GROUP
OBJECTS {
gsmpEventPort,
gsmpEventPortSessionNumber,
gsmpEventSequenceNumber,
gsmpEventLabel
}
STATUS current
DESCRIPTION
"Objects that are contained in the notifications."
::= { gsmpGroups 6 }
gsmpNotificationsGroup NOTIFICATION-GROUP
NOTIFICATIONS {
gsmpSessionDown,
gsmpSessionUp,
gsmpSentFailureInd,
gsmpReceivedFailureInd,
gsmpPortUpEvent,
gsmpPortDownEvent,
gsmpInvalidLabelEvent,
gsmpNewPortEvent,
gsmpDeadPortEvent,
gsmpAdjacencyUpdateEvent
}
STATUS current
DESCRIPTION
"The notifications which indicate specific changes
in the value of objects gsmpSessionTable"
Sjostrand, et. al. Standards Track [Page 41]RFC 3295 GSMP MIB June 2002
::= { gsmpGroups 7 }
END
5. Acknowledgments
The authors would like to thank Avri Doria and Kenneth Sundell for
their contributions to this specification. Also thanks to David
Partain, Michael MacFaden and Bert Wijnen who have contributed
significantly with their SNMP expertise.
6. References
[RFC1155] Rose, M. and K. McCloghrie, "Structure and Identification
of Management Information for TCP/IP-based Internets",
STD 16, RFC 1155, May 1990.
[RFC1212] Rose, M. and K. McCloghrie, "Concise MIB Definitions",
STD 16, RFC 1212, March 1991.
[RFC1215] Rose, M., "A Convention for Defining Traps for use with
the SNMP", RFC 1215, March 1991.
[RFC1157] Case, J., Fedor, M., Schoffstall, M. and J. Davin,
"Simple Network Management Protocol", STD 15, RFC 1157,
May 1990.
[RFC1901] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
"Introduction to Community-based SNMPv2", RFC 1901,
January 1996.
[RFC1905] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
"Protocol Operations for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1905, January 1996.
[RFC1906] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
"Transport Mappings for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1906, January 1996.
[RFC1987] Newman, P, Edwards, W., Hinden, R., Hoffman, E., Ching
Liaw, F., Lyon, T. and Minshall, G., "Ipsilon's General
Switch Management Protocol Specification," Version 1.1,
RFC 1987, August 1996.
[RFC2021] Waldbusser, S., "Remote Network Monitoring Management
Information Base Version 2 using SMIv2", RFC 2021,
January 1997.
Sjostrand, et. al. Standards Track [Page 42]RFC 3295 GSMP MIB June 2002
[RFC2026] Bradner, S., "The Internet Standards Process - Revision
3", BCP 9, RFC 2026, October 1996.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2397] Newman, P, Edwards, W., Hinden, R., Hoffman, E., Ching
Liaw, F., Lyon, T. and Minshall, G., "Ipsilon's General
Switch Management Protocol Specification," Version 2.0,
RFC 2397, March 1998.
[RFC2434] Narten, T. and H. Alvestrand, "Guidelines for Writing an
IANA Considerations Section in RFCs.", BCP 26, RFC 2434,
October 1998.
[RFC2514] Noto, M., E. Spiegel, K. Tesink, "Definition of Textual
Conventions and OBJECT-IDENTITIES for ATM Management",
RFC 2514, February 1999.
[RFC2570] Case, J., Mundy, R., Partain, D. and B. Stewart,
"Introduction to Version 3 of the Internet-standard
Network Management Framework", RFC 2570, April 1999.
[RFC2571] Harrington, D., Presuhn, R. and B. Wijnen, "An
Architecture for Describing SNMP Management Frameworks",
RFC 2571, April 1999.
[RFC2572] Case, J., Harrington D., Presuhn R. and B. Wijnen,
"Message Processing and Dispatching for the Simple
Network Management Protocol (SNMP)", RFC 2572, April
1999.
[RFC2573] Levi, D., Meyer, P. and B. Stewart, "SNMP Applications",
RFC 2573, April 1999.
[RFC2574] Blumenthal, U. and B. Wijnen, "User-based Security Model
(USM) for version 3 of the Simple Network Management
Protocol (SNMPv3)", RFC 2574, April 1999.
[RFC2575] Wijnen, B., Presuhn, R. and K. McCloghrie, "View-based
Access Control Model (VACM) for the Simple Network
Management Protocol (SNMP)", RFC 2575, April 1999.
[RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M. and S. Waldbusser, "Structure of Management
Information Version 2 (SMIv2)", STD 58, RFC 2578, April
1999.
Sjostrand, et. al. Standards Track [Page 43]RFC 3295 GSMP MIB June 2002
[RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M. and S. Waldbusser, "Textual Conventions for
SMIv2", STD 58, RFC 2579, April 1999.
[RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M. and S. Waldbusser, "Conformance Statements for
SMIv2", STD 58, RFC 2580, April 1999.
[RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group
MIB" RFC 2863, June 2000.
[RFC3291] Daniele, M., Haberman, B., Routhier, S. and J.,
Schoenwaelder "Textual Conventions for Internet Network
Addresses", RFC 3291, May 2002.
[RFC3292] Doria, A., Hellstrand, F., Sundell, K. and T. Worster,
"General Switch Management Protocol V3", RFC 3292, June
2002.
[RFC3293] Worster, T., Doria, A. and J. Buerkle, "General Switch
Management Protocol (GSMP) Packet Encapsulations for
Asynchronous Transfer Mode (ATM), Ethernet and
Transmission Control Protocol (TCP)", RFC 3293, June
2002.
7. Intellectual Property Rights
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the
IETF's procedures with respect to rights in standards-track and
standards-related documentation can be found in BCP-11. Copies of
claims of rights made available for publication and any assurances of
licenses to be made available, or the result of an attempt made to
obtain a general license or permission for the use of such
proprietary rights by implementors or users of this specification can
be obtained from the IETF Secretariat.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights which may cover technology that may be required to practice
this standard. Please address the information to the IETF Executive
Director.
Sjostrand, et. al. Standards Track [Page 44]RFC 3295 GSMP MIB June 2002
8. Security Considerations
Assuming that secure network management (such as SNMP v3) is
implemented, the objects represented in this MIB do not pose a threat
to the security of the network.
There are a number of management objects defined in this MIB that
have a MAX-ACCESS clause of read-write and/or read-create. Such
objects may be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure
environment without proper protection can have a negative effect on
network operations.
There are a number of managed objects in this MIB that may contain
sensitive information. They are contained in the gsmpControllerTable
and gsmpSwitchTable. It is thus important to control even GET access
to these objects and possibly to even encrypt the values of these
object when sending them over the network via SNMP. Not all versions
of SNMP provide features for such a secure environment.
SNMPv1 by itself is not a secure environment. Even if the network
itself is secure (for example by using IPSec), even then, there is no
control as to who on the secure network is allowed to access and
GET/SET (read/change/create/delete) the objects in this MIB.
It is recommended that the implementers consider the security
features as provided by the SNMPv3 framework. Specifically, the use
of the User-based Security Model RFC 2574 [RFC2574] and the View-
based Access Control Model RFC 2575 [RFC2575] is recommended.
It is then a customer/user responsibility to ensure that the SNMP
entity giving access to an instance of this MIB, is properly
configured to give access to the objects, only to those principals
(users) that have legitimate rights to indeed GET or SET
(change/create/delete) them.
Sjostrand, et. al. Standards Track [Page 45]
RFC 3295 GSMP MIB June 2002
9. Authors' Addresses
Hans Sjostrand
ipUnplugged
P.O. Box 101 60
S-121 28 Stockholm, Sweden
Phone: +46 8 725 5930
EMail: hans@ipunplugged.com
Joachim Buerkle
Nortel Networks Germany GmbH & Co. KG
Hahnstrasse 37-39
D-60528 Frankfurt am Main, Germany
Phone: +49 69 6697 3281
EMail: joachim.buerkle@nortelnetworks.com
Balaji Srinivasan
CPlane Inc.
897 Kifer Road
Sunnyvale, CA 94086
Phone: +1 408 789 4099
EMail: balaji@cplane.com
Sjostrand, et. al. Standards Track [Page 46]
RFC 3295 GSMP MIB June 2002
10. Full Copyright Statement
Copyright (C) The Internet Society (2002). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Sjostrand, et. al. Standards Track [Page 47]
